EN 6129-2016 en Aerospace series - Blind bolt protruding head high strength pulltype《航空航天系列-封闭凸头螺栓 高强度 拉动式》.pdf

《EN 6129-2016 en Aerospace series - Blind bolt protruding head high strength pulltype《航空航天系列-封闭凸头螺栓 高强度 拉动式》.pdf》由会员分享，可在线阅读，更多相关《EN 6129-2016 en Aerospace series - Blind bolt protruding head high strength pulltype《航空航天系列-封闭凸头螺栓 高强度 拉动式》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 6129:2016Aerospace series Blind bolt,protruding head, high strength,pulltypeBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 6129:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 6129:2016. The UK participation in

2、its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are

3、responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 92623 5 ICS 49.030.20; 49.030.60 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the author

4、ity of the Standards Policy and Strategy Committee on 30 September 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 6129:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 6129 September 2016 ICS 49.030.20; 49.030.60 English Version Aerospace series - Blind

5、bolt, protruding head, high strength, pulltype Srie arospatiale - Boulon aveugle, tte protubrante, haute rsistance, installation en tirant Luft- und Raumfahrt - Blindniet, Universalkopf, hochfest (Zugtyp) This European Standard was approved by CEN on 11 March 2016. CEN members are bound to comply wi

6、th the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Mana

7、gement Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same st

8、atus as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Mal

9、ta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CE

10、N All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 6129:2016 EBS EN 6129:2016EN 6129:2016 (E) 2 Contents Page European foreword 3 1 Scope 4 2 Normative references 4 3 Requirements 4 3.1 Configuration, dimensions and tolerances 4 3.2 Gri

11、p range and weight 4 3.3 Material, finish, lubrication . 5 4 Designation 10 5 Marking . 10 6 Technical specification 10 BS EN 6129:2016EN 6129:2016 (E) 3 European foreword This document (EN 6129:2016) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (

12、ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given th

13、e status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2017, and conflicting national standards shall be withdrawn at the latest by March 2017. Attention is drawn to the possibility that some of the elements of this document may be the s

14、ubject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium,

15、 Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerlan

16、d, Turkey and the United Kingdom. BS EN 6129:2016EN 6129:2016 (E) 4 1 Scope This standard specifies the configuration, dimension, tolerances and mass of a stainless steel blind bolt with protruding head, for aerospace application. 2 Normative references The following documents, in whole or in part,

17、are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace produc

18、ts EN 4473, Aerospace series Aluminium pigmented coatings for fasteners Technical specification1)AS 5272, Lubricant, Solid Film, Heat Cured, Corrosion Inhibiting Procurement Specification2)SAE AMS 5687, Nickel Alloy, Corrosion and Heat-Resistant, Wire 74Ni 15,5Cr 8,0Fe Annealed2)SAE AMS 5737, Steel,

19、 corrosion and heat-resistant, bars, wire, forgings and tubing 15Cr 25.5Ni 1.2Mo 2.1Ti 0.006B 0.30V, consumable electrode melted, 1650 F (899 C), solution and precipitation heat treated2) AMS-QQ-P-35, Passivation treatments for Corrosion-Resistant Steel2) MIL-PRF-46010F, Lubricant, Solid Film, Heat

20、cured, Corrosion Inhibiting NATO Code-S-17383)SAE AS 87132, Lubricant, Cetyl Alcohol, 1- Hexadecanol, Application to fasteners3)DOD-L-85645, Lubricant, Dry Thin Film, Molecular Bonded3)NASM 8975, Fasteners, Blind, High Strength, Installation Formed, Corrosion Resistant Steel, Heat Resistant Steel an

21、d Titanium, General Specification for4)3 Requirements 3.1 Configuration, dimensions and tolerances The configuration, dimensions, tolerances, static and dynamic values shall conform to Figures 1 and 2 and Tables 1 and 2. 3.2 Grip range and weight See Tables 3 and 4. 1)Published as AECMA Prestandard

22、at the date of publication of this standard. 2)Published by: Society of Automotive Engineers (SAE), 400 Commonwealth drive, Warrendale, PA 15096-0001, USA. 3) Published by: Department of Defense (DoD), the Pentagon, Washington, D.C. 20301, USA. 4)Published by: Aerospace Industries Association of Ame

23、rica, Inc. (AIA), 1250 Eye Street, N.W., Washington, D.C. 20005-3924, USA. BS EN 6129:2016EN 6129:2016 (E) 5 3.3 Material, finish, lubrication See Tables 5 and 6. Key 1 Marking, see clause 5. 5 Grip 2 Sleeve shall not rotating. 6 Locking collar 3 Diameter of serrated pin head shall not exceed D max.

24、 7 Shifting anvil: Fasteners are supplied with shifting anvil of manufacturers option. The shifting anvil is not part of the installed fastener 4 Serrated pin Figure 1 Configuration Dimensions BS EN 6129:2016EN 6129:2016 (E) 6 Key 1 Grip 2 Blind side head may be installed on 7 max. slope Figure 2 Ty

25、pical installation Table 1 Dimensions and tolerances Dimensions in mm (inch) Diameter code A Theor. B Ref. null D null J N Q null D1 null D2 P a null P2 min. max. min. max. 0,03 (.001) 0,13 (.005) 0,25 (.010) 0,13 (.005) max. max. max. min. 05 7,52 (.296) 8,33 (.328) 1,70 (.067) 1,96 (.077) 4,14 (.1

26、63) 9,53 (.375) 3,99 (.157) 1,70 (.067) 3,05 (.120) 2,16 (.085) 7,62 (.300) 5,49 (.216) 06 9,04 (.356) 10,01 (.394) 2,03 (.080) 2,29 (.090) 5,03 (.198) 9,53 (.375) 4,45 (.175) 2,21 (.087) 3,81 (.150) 2,79 (.110) 8,13 (.320) 6,86 (.27) 08 12,07 (.475) 13,34 (.525) 2,72 (.107) 2,97 (.117) 6,58 (.259)

27、9,53 (.375) 4,62 (.182) 2,79 (.110) 4,83 (.190) 3,66 (.144) 9,40 (.370) 8,89 (.35) Diameter code R S Ref. Z J1 J2 X E C1 Ref. C2 F G Hole limits max. min. 0,76 (.030) 0,76 (.030) max. min. 0,05 (.002) 5 5 min. max. 05 0,25 (.010) 5,84 (.232) 21,44 (.844) 15,14 (.596) 14,91 (.587) 2,54 (.100) 0,13 (.

28、005) 3,30 (.130) 0,80 (.032) 45 30 4,17 (.164) 4,24 (.167) 06 0,38 (.015) 7,42 (.292) 22,23 (.875) 15,62 (.615) 15,37 (.605) 3,30 (.130) 0,13 (.005) 3,30 (.130) 0,80 (.032) 45 30 5,06 (.199) 5,13 (.202) 08 0,51 (.020) 9,17 (.361) 25,40 (1.000) 18,42 (.725) 16,97 (.668) 3,81 (.150) 0,13 (.005) 3,30 (

29、.130) 0,80 (.032) 45 30 6,60 (.260) 6,68 (.263) aIn the length P of D may be 0,05 mm (.002) undersize. BS EN 6129:2016EN 6129:2016 (E) 7 Table 2 Static values Dimensions in kN (lbs) Diameter code Installed strength Single shear Tensile strength Tensile preload Spindle retention min. min. min. min. 0

30、5 8,811 (1980) 5,117 (1150) 0,512 (115) 2,558 (575) 06 13,016 (2925) 7,520 (1690) 0,752 (169) 3,760 (845) 08 22,250 (5000) 12,905 (2900) 1,29 (290) 6,408 (1440) Table 3 Grip range (1 von 2) Dimensions in mm (inch) Grip length code Under lap Grip range Over lap Diameter code only 05 dia. only 06 to 0

31、8 dia. 05 to 08 dia. 05 06 08 L K L K L K min. min. min. max. max. Ref. max. Ref. max. Ref. max. 01 0,79 (.031) 2,44 (.096) 2,82 a (.111)a7,19 (.283) 11,35 (.447) 02 2,13 (.084) 1,99 (.078) 2,39 (.094) 3,99 (.0157) 4,39 (.173) 8,79 (.346) 12,95 (.51) 9,47 (.373) 14,48 (.57) 10,49 (.413) 16,76 (.66)

32、03 3,71 (.146) 3,56 (.14) 3,96 (.156) 5,59 (.220) 5,99 (.236) 10,37 (.408) (14,53 (.572) 11,05 (.435) 16,05 (.632) 12,07 (.475) 18,34 (.722) 04 5,31 (.209) 5,16 (.203) 5,56 (.219) 7,16 (.282) 7,57 (.298) 11,97 (.471) 16,13 (.635) 12,65 (.498) 17,65 (.695) 13,67 (.538) 19,94 (.785) 05 6,88 (.271) 6,7

33、3 (.265) 7,14 (.281) 8,76 (.345) 9,17 (.361) 13,54 (.533) 17,70 (.697) 14,22 (.560) 19,23 (.757) 15,24 (.6) 21,51 (.847) 06 8,48 (.334) 8,33 (.328) 8,74 (.344) 10,34 (.407) 10,74 (.423) 15,14 (.596) 19,30 (.76) 15,82 (.623) 20,83 (.82) 16,84 (.663) 23,11 (.91) 07 10,06 (.396) 9,91 (.39) 10,31 (.406)

34、 11,94 (.470) 12,34 (.486) 16,71 (.658) 20,88 (.822) 17,40 (.685) 22,40 (.882) 18,42 (.725) 24,69 (.972) 08 11,66 (.459) 11,51 (.453) 11,91 (.469) 13,51 (.532) 13,92 (.548) 18,29 (.72) 22,45 (.884) 19,00 (.748) 24,00 (.945) 20,02 (.788) 26,29 (1.035) 09 13,23 (.521) 13,08 (.515) 13,49 (.531) 15,11 (

35、.595) 15,52 (.611) 19,86 (.782) 24,03 (.946) 20,57 (.81) 25,58 (1.007) 21,59 (.85) 27,86 (1.097) 10 14,83 (.584) 14.68 (.578) 15,09 (.594) 16,69 (.657) 17,09 (.673) 21,46 (.845) 25,63 (1.009) 22,17 (.873) 27,18 (1.07) 23,19 (.913) 29,46 (1.16) 11 16,41 (.646) 16,26 (.64) 16,66 (.656) 18,29 (.720) 18

36、,69 (.736) 23,06 (.908) 27,23 (1.072) 23,77 (.936) 28,78 (1.133) 24,79 (.976) 31,06 (1.223) 12 18,01 (.709) 17,86 (.703) 18,26 (.719) 19,86 (.782) 20,27 (.798) 24,64 (.970) 28,80 (1.134) 25,35 (.998) 30,35 (1.195) 26,37 (1.038) 32,64 (1.285 13 19,58 (.771) 19,43 (.765) 19,84 (.781) 21,46 (.845) 21,8

37、7 (.861) 26,24 (1.033) 30,40 (1.197) 26,95 (1.061) 31,95 (1.258) 27,97 (1.101) 34,24 (1.348) BS EN 6129:2016EN 6129:2016 (E) 8 Table 3 Grip range (2 von 2) Dimensions in mm (inch) Grip length code Under lap Grip range Over lap Diameter code only 05 dia. only 06 to 08 dia. 05 to 08 dia. 05 06 08 L K

38、L K L K min. min. min. max. max. Ref. max. Ref. max. Ref. max. 14 21,184 (.834) 21,03 (.828) 21,44 (.844) 23,04 (.907) 23,44 (.923) 27,81 (1.095) 31,98 (1.259) 28,52 (1.123) 33,53 (1.32) 29,54 (1.163) 35,81 (1.41) 15 22,76 (.896) 22,61 (.89) 23,01 (.909) 24,64 (.970) 25,04 (.986) 29,41 (1.158) 33,58

39、 (1.322) 30,12 (1.186) 35,13 (1.383) 31,14 (1.226) 37,41 (1.473) 16 24,36 (.959) 24,21 (.953) 24,61 (.969) 26,21 (1.032) 26,65 (1.049) 30,99 1.220 35,15 1.384 31,70 (1.248) 36,70 (1.445) 32,72 (1.288) 38,99 (1.535) 17 25,81 (1.016) 26,19 (1.031) 27,81 (1.095) 28,22 (1.111) 33,30 (1.311) 38,30 (1.508

40、) 34,32 (1.351) 40,59 (1.598) 18 27,38 (1.078) 27,79 (1.094) 29,39 (1.157) 29,79 (1.173) 34,87 (1.373) 39,88 (1.570) 35,89 (1.413) 42,16 (1.660) 19 28,98 (1.141) 29,36 (1.156) 30,99 (1.220) 31,39 (1.236) 36,45 (1.435) 41,48 (1.633) 37,49 (1.476) 43,76 (1.723) 20 30,56 (1.203) 30,96 (1.219) 32,56 (1.

41、282) 32,97 (1.298) 38,05 (1.498) 43,05 (1.695) 39,07 (1.538) 45,34 (1.785) 21 32,13 (1.265) 32,54 (1.281) 34,16 (1.345) 34,54 (1.360) 39,62 (1.560) 44,65 (1.758) 40,67 (1.601) 46,94 (1.848) 22 33,73 (1.328) 34,14 (1.344) 35,74 (1.407) 36,14 (1.423) 41,22 (1.623) 46,23 (1.820) 42,24 (1.663) 48,51 (1.

42、910) 23 35,31 (1.390) 35,71 (1.406) 37,34 (1.470) 37,72 (1.485) 42,80 (1.685) 47,83 (1.883) 43,84 (1.726) 50,11 (1.973) 24 36,91 (1.453) 37,31 (1.469) 38,91 (1.532) 39,32 (1.548) 44,40 (1.748) 49,40 (1.945) 45,42 (1.788) 51,69 (2.035) 25 40,01 (1.575) 38,89 (1.531) 40,51 (1.595) 40,89 (1.610) 45,97

43、(1.810) 51,00 (2.008) 47,02 (1.851) 53,29 (2.098) aOnly for 05 dia. BS EN 6129:2016EN 6129:2016 (E) 9 Table 4 Weight Weight in kg (lbs) /1000 parts. Grip length code Diameter code 05 06 08 01 1,23 (2.72) 02 1,39 (3.06) 2,28 (5.02) 4,89 (10.78) 03 1,56 (3.43) 2,53 (5.57) 5,32 (11.73) 04 1,72 (3.80) 2

44、,77 (6.11) 5,75 (12.68) 05 1,89 (4.17) 3,02 (6.66) 6,19 (13.64) 06 2,06 (4.55) 3,27 (7.21) 6,62 (14.59) 07 2,23 (4.92) 3,52 (7.75) 7,05 (15.54) 08 2,40 (5.29) 3,77 (8.30) 7,48 (16.49) 09 2,57 (5.67) 4,01 (8.85) 7,92 (17.45) 10 2,74 (6.04) 4,26 (9.39) 8,35 (18.40) 11 2,91 (6.41) 4,51 (9.94) 8,78 (19.

45、35) 12 3,08 (6.79) 4,75 (10.48) 9,21 (20.30) 13 3,25 (7.16) 5,00 (11.02) 9,64 (21.25) 14 3,42 (7.54) 5,25 (11.57) 10,07 (22.20) 15 3,59 (7.91) 5,49 (12.11) 10,50 (23.15) 16 5,74 (12,65) 10,93 (24.10) 17 5,98 (13.19) 11,36 (25.05) 18 6,23 (13.73) 11,79 (26.00) 19 6,47 (14.27) 12,22 (26.95) 20 6,72 (1

46、4.81) 12,66 (27.90) 21 6,96 (15.35) 13,09 (28.85) 22 7,21 (15.89) 13,52 (29.80) 23 7,45 (16.43) 13,95 (30.75) 24 7,70 (16.97) 14,38 (31.70) 25 7,94 (17.51) 14,81 (32.65) BS EN 6129:2016EN 6129:2016 (E) 10 Table 5 Material, finish, lubrication Material/ Finish code Material Finish Lubrication Sleeve

47、Serrated pin Locking collar Sleeve Serrated pin Locking collar C A-286 Cres per AMS 5737 A-286 Cres per AMS 5737 A-286 Cres per AMS 5737; 316 Cres per AMS 5690 or Inconel per AMS 5687 See Table 6. Passivated per AMS-QQ-P-35 Passivated per AMS-QQ-P-35 a None aIf lubricated, pin and/or collar shall be

48、 lubricated per AS5272 Type 1, MIL-L-46010 Type 1 or 3, MIL-L-87132 or DOD-L-85645. Table 6 Sleeve finish codes Code Material Finish P A-286-Cres Passivated per AMS-QQ-P-35 H Aluminium coated (Hi-Kote1) per EN 4473 4 Designation EXAMPLE 5 Marking Marking as per EN 2424 style B on rivet head (EN Stan

49、dard Number, grip length code and manufacturers identification required). Instead of the EN Standard Number, the manufacturers material code or part number shall be permissible. Single digit marking is permissible for grip length code less than 10. Shifting anvil and / or serrated pin shall be in red. 6 Technical specification See NASM 8975 except strength requirements as defined in Table 2. This page delibe