EN 40-5-2002 en Lighting Columns - Part 5 Requirements for Steel Lighting Columns《灯柱 第5部分 钢灯柱要求》.pdf

《EN 40-5-2002 en Lighting Columns - Part 5 Requirements for Steel Lighting Columns《灯柱 第5部分 钢灯柱要求》.pdf》由会员分享，可在线阅读，更多相关《EN 40-5-2002 en Lighting Columns - Part 5 Requirements for Steel Lighting Columns《灯柱 第5部分 钢灯柱要求》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 40-5 12002 Lighting columns Part 5: Requirements for steel lighting columns The European Standard EN 40-5:2002 has the status of a British Standard ICs 77.140.01; 93.080.40 NO COPYING WITHOUT aSI PERMLSSION EXCEPT AS PERMITIED BY COPYRIGHT LAW British Standards BS EN 40-512002

2、 National foreword This British Standard is the official English language version ofEN 40-5:2002. It supersedes BS EN 40-5:2000 which is withdrawn. EN 40-5:2002 is a candidate “harmonized” European Standard and fully takes into account the requirements ofthe European Commission mandate W111, Circula

3、tion fixtures, given under the EU Construction Products Directive (89/106/EEC), and intended to lead to CE marking. The date ofapplicability of EN 40-5:2002 as a “harmonized” European Standard, i.e. the date after which this standard may be used for CE marking purposes, is subject to an announcement

4、 in the meia1 Journal of the European Communities. EN 40-5:2002 is the subject of transitional arrangements agreed under the European Commission mandate. The Member States have agreed a nominal transition period for the Co-existence of EN 40-5:2002 and their corresponding national standard(s). It is

5、 intended that this period will comprise a nominal nine month period during which any required changes to national regulations are to be made, followed by a further nominal twelve month period for the implementation of CE marking. At the end of this Co-existence period, the national standard(s) will

6、 be withdrawn. In the UK, there are nocorresponding national standards. The UKparticipation in its preparation was entrusted by Technical Committee B/509, Road equipment, to Subcommittee B/509/50, Road equipment - Street lighting columns, which has the responsibility to: This British Standard, havin

7、g been prepared under the direction of the Building and Civil Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 17 July 2002 - - aid enquirers to understand the text; present to the responsible international/European

8、 committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary.

9、Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSIElectronic Catalogue or

10、of British Stan dards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for their correct application. Compliance with a British Standard does not ofitself confer immunity from legal obligations. Summary of pages This document comp

11、rises a front cover, an inside front cover, the EN title page, pages 26, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication OBSI 17 July 2002 ISBN O 580 40082 4 Amd. No. I Date I Co

12、mments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 40-5 April 2002 ICs 77.140.01; 93.080.40 Supersedes EN 40-52000 English version Lighting columns - Part 5: Requirements for steel lighting co I u m ns Candlabres dclairage public - Partie 5: Exigences pour les candlabres dclairage public en

13、 acier Lichtmaste -Teil 5: Anforderungen fr Lichtmaste aus Stahl This European Standard was approved by CEN on 25 February 2002. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard

14、 without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other languag

15、e made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Icela

16、nd, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FUR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2002 CEN All rights of e

17、xploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 40-52002 E EN 40-52002 (E) Contents Foreword 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Scope Normative references Terms and definitions Materials Dimensions Design and design verification Welding Joints Pr

18、otection against mechanical impact Internal fmish and sharp edges Corrosion protection Marking Conformity control Acceptance criteria Re-testing Performance under vehicle impact - Passive safety Annex A (informative) Corrosion protection measures for steel lighting columns Annex B (informative) Reco

19、mmendations for storage and installation Annex C (informative) Bibliography Annex D (normative) Initial type tests page 3 4 4 6 6 6 6 7 7 8 8 9 9 10 14 16 16 17 19 20 21 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive 22 2

20、EN 40-52002 (E) Foreword This document EN 40-5:2002 has been prepared by Technical Committee CEN/TC 50 “Lighting columns and spigots“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by en

21、dorsement, at the latest by October 2002, and conflicting national standards shall be withdrawn at the latest by January 2004. This document supersedes EN 40-5:2000. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and su

22、pports essential requirements of the EU Directive 89/106/EEC. For relationship with EU Directive 89/106EEC see informative annex ZA which is an integral part of this document. In this standard the annexes A, B and C are informative and the annex D is normative. Wherever reference is made to classes,

23、 they are considered to be technical classes and not classes according to 3(2) of the Construction Products Directive. This European Standard is the fifth in a series relating to specifications for lighting columns. At present the Parts of this standard are as follows: Part 1 : Definitions and terms

24、 Part 2: General requirements and dimensions Part 3: Design and verification 3-1 : Specification for characteristic loads 3-2: Verification by testing 3-3: Verification by calculation Part 4: Requirements for reinforced and prestressed concrete lighting columns Part 5: Requirements for steel lightin

25、g columns Part 6: Requirements for aluminium lighting columns Part 7: Requirements for fibre reinforced polymer composite lighting columns According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard:

26、Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, 3 EN 40-52002 (E) Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 1 Scope This European Standard specifies requirements for steel lighting column

27、s. It includes materials and conformity control. It applies to post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for side entry lanterns. This European Standard specifies performance related to the essential requirements of resist

28、ance to horizontal (wind) loads and performance under vehicle impact (passive safety) in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this European Standard or available in separate European Standards. It provides for the ev

29、aluation of conformity of the products to this European Standard. 2 Normative references This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed

30、 hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 40-1

31、 prEN 40-2: 1999 EN 40-3-1 EN 40-3-2 prEN 40-3-3 EN 288-1 EN 288-2 EN 288-3 Lighting columns - Part 1: Definitions and terms. Lighting columns - Part 2: General requirements and dimensions. Lighting columns - Design and verification - Part 3-1: Specification for characteristic loads. Lighting column

32、s - Design and verification - Part 3-2: Verification by testing. Lighting columns - Design and verification - Part 3-3: Verification by calculation. Specification and approval of welding procedures for metallic materials - Part 1 : General rules for fusion welding. Specification and approval of weld

33、ing procedures for metallic materials - Part 2: Welding procedure specification for arc welding. Specification and approval of welding procedures for metallic materials - Part 3: Welding procedure tests for arc welding of steels. 4 EN 40-52002 (E) EN 288-8 EN 571-1 EN 970 EN 1011-1 EN 1011-2 EN 1011

34、-3 EN 10025 EN 10088 EN 10149-1 EN 10149-2 EN 10204 EN 10210 EN 10219 EN 12767 EN 50 102 ENISO 1461 IS0 2063 IS0 8501-1 Specification and approval of welding procedures for metallic materials - Part 8: Approval by a pre-production welding test. Non-destructive testing - Penetrant testing - General p

35、rinciples. Non-destructive examination of fusion welds - Visual examination. Welding - Recommendations for welding of metallic materials - Part 1 : General guidance for arc welding. Welding - Recommendations for welding of metallic materials - Part 2: Arc welding of ferritic steels. Welding - Recomm

36、endations for welding of metallic materials - Part 3: Arc welding of stainless steels. Hot rolled products of non-alloy structural steels - Technical delivery conditions (includes amendment Al : 1993). Stainless steels. Hot-rolled flat products made of high yield strength steels for cold forming - P

37、art 1 : General delivery conditions. Hot-rolled flat products made of high yield strength steels for cold forming - Part 2: Delivery conditions for thermomechanically rolled steels. Metallic products - Types of inspection documents. Hot finished structural hollow sections of non-alloy and fine grain

38、 structural steels. Cold formed structural hollow section of non-alloy and fine grain steels. Passive safety of support structures for road equipment - Requirements and test methods. Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code).

39、Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (IS0 1461 : 1999). Metallic and other inorganic coatings - Thermal spraying - Zinc, aluminium and their alloys. Preparation of steel substances before application of paints and related products - Visu

40、al assessment of surface cleanliness - Part 1 : Rust grades and 5 EN 40-52002 (E) preparation grades of uncoated steel substrates and of steel substates after overall removal of previous coatings. IS0 9717 Phosphate conversion coatings for metals - Method of specifying requirements. 3 Terms and defi

41、nitions For the purposes of this European Standard, the terms and definitions given in EN 40-1 apply. 4 Materials 4.1 Steel The steel used shall comply with one of the following standards, and be suitable for hot-dip galvanizing when such surface protection is required. Rimming steel shall not be us

42、ed. Steel sheet and plate: EN 10025 except grade S 185 EN 10149-1 and EN 10149-2 Hot-Fished steel tube: EN 10210 Cold-formed steel tube: EN 10219 Stainless steels: EN 10088 4.2 Foundation bolts The minimm mechanical properties of the steel used for foundation bolts shall comply with the requirements

43、 of EN 10025 grade S 235 JR 5 Dimensions Dimensions shall be in accordance with prEN 40-2. 6 Design and design verification The column shall be designed to sustain safely the dead loads and the wind loads specified in EN 40-3-1. The structural design of a lighting column shall be verified either by

44、calculation in accordance with prEN 40-3-3 or by testing in accordance with EN 40-3-2. 6 EN 40-52002 (E) 7 Welding 7.1 Welding process Arc welding of ferritic steels shall be in accordance with EN 1 O 1 1 - 1 and EN 1 O 1 1-2. Arc welding of stainless steels shall be in accordance with EN 1 O 1 1 -

45、1 and EN 1 O 1 1-3. 7.2 Welding procedures Welding procedures shall comply with EN 288-1 and EN 288-2. Written procedures shall be provided for the main structural joints which shall include where relevant, the flange plate joint, the base compartment to shaft joint, the door reinforcement, any inte

46、rmediate column joint, the column to bracket joint and the column seam weld when this is carried out at the time of column manufacture. Welding procedures shall be approved in accordance with EN 288-8. Pre-production test pieces shall represent the main assembly types. Welding procedures shall be ve

47、rified by testing to the requirements in accordance with EN 288- 3. The welding consumables and procedures used shall be such that the mechanical properties of the as-deposited weld metal will not be less than the respective minimum values required by the designers specification for the parent metal

48、 being welded. Verification shall be by a welding coordinator. Procedures shall be reviewed and reapproved where necessary after a period of seven years. 7.3 Welding personnel Welders shall be tested for each approved procedure to which they shall be required to work (see 7.2). Test pieces shall be

49、used as in the original procedure tests. The approval range shall be in accordance with that for the original procedure. 8 Joints 8.1 General All joints shall be designed to the requirements specified in clause 6. NOTE Design of joint details should avoid moisture retention and corrosion. 7 EN 40-52002 (E) 8.2 Friction joints When joints are made by drawing parts together to form a friction joint the additional stresses in the connection shall be included in the design. 8.3 Welded joints Welded joints shall comply with the requirements of clause 7 9 Protection against mecha