EN 3848-2001 en Aerospace Series - Semi-Finished Metallic Products - Methods of Measuring Form Deviations《航空航天系列 金属半成品 测量形状偏差的方法》.pdf

《EN 3848-2001 en Aerospace Series - Semi-Finished Metallic Products - Methods of Measuring Form Deviations《航空航天系列 金属半成品 测量形状偏差的方法》.pdf》由会员分享，可在线阅读，更多相关《EN 3848-2001 en Aerospace Series - Semi-Finished Metallic Products - Methods of Measuring Form Deviations《航空航天系列 金属半成品 测量形状偏差的方法》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES Semi-finished metallic products - Methods of measuring form deviations The European Standard EN 3848:ZOOl has the status of a British Standard ICs 49.035 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 3848:2001 BS EN 3848:ZOOl Amd. No.

2、National foreword Date Comments This British Standard is the official English language version of EN 3848:2001. The UK participation in its preparation was entrusted to Technical Committee ACEI61, Inspection and testing requirements for aerospace metallic materials, which has the responsibility to:

3、- - aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations r

4、epresented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Corresp

5、ondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A Bntish Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not o

6、f itself confer immunity from legal obligations. This British Standard, having been prepared under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 23 October 2001 Summary of pages This document

7、 comprises a front cover, an inside front cover, the EN title page, pages 2 to 10, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Q BSI 23 October 2001 ISBN O 580 38607 4 EUROPE

8、AN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3848 September 2001 ICs 49.035 English version Aerospace series - Semi-finished metallic products - Methods of measuring form deviations Srie arospatiale - Demi-produits mtalliques - Mthodes de measure des dfauts de forme Luft- und Raumfahrt - Metallisc

9、hes Halbzeug - Meverfahren fr Formabweichungen This European Standard was approved by CEN on 2 May 2001 CEN members are bound to comply with the CENICENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

10、 Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation un

11、der the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland. Ireland, Italy, Luxe

12、mbourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FUR NORMUNG Management Centre: rue de Stascart, 36 6-1050 Brussels O 2001 CEN All rights of exploitation in any form and by

13、any means reserved worldwide for CEN national Members. Ref. No. EN 3 - folded sections: see EN 2065. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text

14、 and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies

15、. EN 2065 EN 2066 IS0 1101 3 Folded profiles - Aluminium alloys - General tolerances - Aerospace series Aerospace series - Extruded sections in aluminium alloys - General tolerances Technical drawings, geometrical tolerancing; tolerances of form, orientation, location and runout; generalities, defin

16、itions, symbols of drawings M easu ring condi ti on The dimensions shall be measured using measuring instruments which are of the accuracy required by the dimensions and the dimensional tolerances. All dimensions shall be checked at the ambient temperature of the workshop or laboratory, and, in the

17、event of dispute, at a temperature between 15 “C and 25 OC. Surface plates used for the measurement of form deviations shall be flat to within I 1 % of the requisite product form deviation being measured. 4 Sheet and plate 4.1 Squareness The squareness deviation shall be measured as the difference i

18、n length of diagonals AA and BB as shown in figure 1. 4.2 Lateral curvature The lateral curvature (f) shall be measured as indicated in figure 2, with the sheet or plate resting on a horizontal surface plate. 3 . . . . I EN 3848:2001 (E) 4.3 Flatness 4.3.1 Flatness tolerance zone See IS0 1101. The t

19、olerance zone is limited by two parallel planes a distance “I“ apart. The area shall be between two parallel planes with distance “t“. See figure 3. 4.3.2 Measurement Deviation from flatness (0 resulting from arching, buckling or edge waves, shall be measured as shown in figures 4 to 6, using a ligh

20、tweight straight-edge and a feeler gauge, dial gauge or scale, with the sheet or plate resting on a horizontal surface plate concave side upwards, except when the size of the product precludes this. 5 Round bar 5. I Straightness Deviation from straightness (Y,) per metre of total length (X,), expres

21、sed in mm/m, and (Y,) on any length (X2), as specified in the dimensional standard, shall be measured as shown in figure 7, with the bar placed on a surface plate so that its mass minimizes the deviation. 5.2 Roundness Roundness deviation shall be measured as the difference between the maximum and m

22、inimum diameters at the same cross-section. 6 Hexagonal bar 6.1 Straightness Deviation from straightness (Y,) per metre of total length (X,), expressed in mmlm, and (Y,) on any length (X,), as specified in the dimensional standard, shall be measured as shown in figure 7, with the bar placed on a sur

23、face plate so that its mass minimizes the deviation. 6.2 Twist Twist (v) shall be measured as shown in figure 8, with the bar placed on a horizontal base plate so that its mass minimizes the deviation. Twist is the maximum distance, at any point along the measuring length between the bottom surface

24、of the bar and the surface plate. 6.3 Surface flatness Surface flatness (0 shall be measured on all faces as shown in figure 9. 4 EN 3848:2001 (E) 7 Square and rectangular bar 7.1 Straightness Deviation from straightness (Yl) per metre of total length (Xi), expressed in mmlm, and (Y,) on any length

25、(X,), as specified in the dimensional standard, shall be measured as shown in figure 7, with the bar placed on a surface plate so that its mass minimizes the deviation. 7.2 Twist Twist (v) shall be measured as shown in figure 10, with the bar placed on a horizontal plate so that its mass minimizes t

26、he deviation. The twist is the maximum distance, at any point along the measuring length between the bottom surface of the bar and the surface plate. 7.3 Squareness The squareness deviation (z) shall be measured as shown in figure 11. 7.4 Surface flatness Surface flatness (Fj shall be measured on al

27、l faces as shown in figure 12. 8 Circular tube 8.1 Straightness Deviation from straightness (Y,) per metre of total length (X,), expressed in mm/m, and (Y,) on any length (Xz), as specified in the dimensional standard, shall be measured as shown in figure 7, with the tube placed on a surface plate s

28、o that its mass minimizes the deviation. 8.2 Roundness Roundness deviation shall be measured as the difference between the maximum and minimum outside diameters at the same cross-section, see figure 13. 8.3 Eccentricity Eccentricity (i) shall be measured as half the difference between the maximum an

29、d the minimum wall thickness at the same cross-section, as shown in figure 14. 5 . ,- , EN 38482001 (E) A. Figure 1 - Squareness of sheet and plate Side edge (concave side) tr FI J Straight-edge korb F = lateral curvature length of the sheet or plate b = width of the sheet or plate = Figure 2 - Late

30、ral curvature of sheet and plate Figure 3 - Definition of flatness 6 EN 3848:2001 (E) a= b= I= f= t= fmx. = w= t= thickness of the sheet or plate width of the sheet or plate length of the sheet or plate length of the wave deviation from flatness tolerance zone (space between two parallel planes) max

31、imum acceptable deviation from flatness a+ fmx Figure 4 -Arching of sheet and plate Straight-edge W FI- Surface plate I I f = deviation from flatness W = length of buckle (chord) Figure 5 - Buckling of sheet and plate 7 EN 3848:2001 (E) Straight-edge 1 Surface plate I. fj f = deviation from flatness

32、 W = length of edge wave (chord) Figure 6 - Edge waves of sheet and plate Surface plate I I I I I I I XI YI = deviation from straightness on total length Xi Y2 = deviation from straightness on length XZ Figure 7 - Deviation from straightness of bar and tube Surface plate Y = twist a = across flat of

33、 the bar Figure 8 - Twist of hexagonal bar 8 EN 38482001 (E) Side edge (concave face1 , Straight-edge F = deviation from surface flatness a = across flat of the bar Figure 9 - Surface flatness of hexagonal bar Surface plate 7 v = twist a = thickness of the bar Figure 10 - Twist of square and rectang

34、ular bar z = squareness deviation Figure 11 - Squareness deviation of square and rectangular bar 9 EN 3848:2001 (E) r Straight-edge -* Side edge - (concave face) / F = deviation from lateral flatness a = thickness of the bar b = widthof the bar Figure 12 - Surface flatness of square and rectangular

35、bar I 23 c O cl 1 - Roundness deviation = kx. - “. 2 Figure 14 - Eccentricity of tube 10 BS EN 3848:2001 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution 3SI is the independent national body responsible for preparing British Standards. It presents the UK view on standards

36、 in Europe and at the nternational level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or 3ditions. t is the constant aim of BSI to improve the quality of our

37、 products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: O20 8996 7400. BSI off

38、ers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8

39、996 7001. Standards are also available from the BSI website at htto:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provide

40、s a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 02

41、0 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: O20 8996 7001. Further

42、 information about BSI is available on the BSI website at http:/www.bsi-loba1 corn Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Pate

43、nts Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of neces

44、sary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.