EN 3155-045-2006 en Aerospace series - Electrical contacts used in elements of connection - Part 045 Contacts electrical female type A double crimping class T - Product standard《航空.pdf

《EN 3155-045-2006 en Aerospace series - Electrical contacts used in elements of connection - Part 045 Contacts electrical female type A double crimping class T - Product standard《航空.pdf》由会员分享，可在线阅读，更多相关《EN 3155-045-2006 en Aerospace series - Electrical contacts used in elements of connection - Part 045 Contacts electrical female type A double crimping class T - Product standard《航空.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 3155-045:2006Aerospace series Electrical contacts used in elements of connection Part 045: Contacts, electrical, female, type A, double crimping, class T Product standardThe European Standard EN 3155-045:2006 has the status of a British StandardICS 49.060g49g50g3g38g50g51g60g44

2、g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3155-045:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee o

3、n 29 September 2006 BSI 2006ISBN 0 580 49175 7National forewordThis British Standard was published by BSI. It is the UK implementation of EN 3155-045:2006.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to S

4、ubcommittee ACE/6/-/3, Aerospace Connectors.A list of organizations represented on ACE/6/-/3 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a Britis

5、h Standard cannot confer immunity from legal obligations.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3155-045May 2006ICS 49.060English VersionAerospace series - Electrical contacts used in elements ofconnection - Part 045: Contacts, elec

6、trical, female, type A,double crimping, class T - Product standardSrie arospatiale - Contacts lectriques utiliss dans lesorganes de connexion - Partie 045 : Contacts lectriques,femelles, type A, double sertissage, classe T - Norme deproduitLuft- und Raumfahrt - Elektrische Kontakte zur Verwendungin

7、Verbindungselementen - Teil 045: ElektrischerBuchsenkontakt, Typ A, doppelt gecrimpt, Klasse T -ProduktnormThis European Standard was approved by CEN on 26 September 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

8、Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, Frenc

9、h, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic,

10、 Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALIS

11、ATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3155-045:2006: E2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Terms an

12、d definitions.4 4 Required characteristics 5 4.1 Dimensions, mass.5 4.2 Material, protective plating.6 4.3 Permissible cables6 4.4 Cable stripping6 4.5 Tooling.6 4.6 Tests 7 4.7 Gauges.8 5 Designation .8 6 Marking 8 7 Technical specification.8 EN 3155-045:20063 Foreword This European Standard (EN 31

13、55-045:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services

14、 of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2006, and conflicting national standards shall be withdrawn at the lat

15、est by November 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national

16、standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portuga

17、l, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3155-045:20064 1 Scope This standard specifies the required characteristics, tests and tooling applicable to female electrical contacts 045, type A, double crimping, class T, used in elements of connection accordin

18、g to EN 3155-002. It shall be used together with EN 3155-001. The associated male contact is defined in EN 3155-044. Double crimping contact has a barrel which is design to crimp conductor and jacket of cable in two locations, one on the conductor and the other on the jacket. This way protect the co

19、nductor from mechanical strengths. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

20、applies. EN 2591-*, Aerospace series Elements of electrical and optical connection Test methods. EN 3155-001, Aerospace series Electrical contacts used in elements of connection Part 001: Technical specification.1)EN 3155-002, Aerospace series Electrical contacts used in elements of connection Part

21、002: List and utilization of contacts. EN 3155-044, Aerospace series Electrical contacts used in elements of connection Part 044: Contacts, electrical, male 044, type A, double crimping, class T Product standard. MIL-DTL-22520, Crimping tools, terminal, hand or power actuated, wire termination, and

22、tool kits general specification for.2)MIL-I-81969, Installing and removal tools, connector electrical contact, general specification for.2)3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 3155-001 apply. *All its parts quoted in this standard. 1) Publi

23、shed as AECMA Prestandard at the date of publication of this standard. 2) Published by: Department of Defense (DOD), the Pentagon, Washington D.C. 20301, USA. EN 3155-045:20065 4 Required characteristics 4.1 Dimensions, mass See Figure 1 and Table 1. Dimensions and tolerances are given in millimetre

24、s. Key 1 G max., see NOTE 1. 2 0,25 max., see NOTE 2. 3 Manufacturer identification 4 Diameter H (one side only) 5 White dot NOTE 1 Position of electrical contact point NOTE 2 Clearance between sleeve and body of the contact Figure 1 EN 3155-045:20066 Table 1 Size A F G J Contact Barrel max. B C D E

25、 min. max. H 12,32 4,34 0,84 1,98 0,81 1,74 20 22 16,66 12,17 4,06 0,74 1,93 1,05 1,14 0,66 1,69 Size K1K2M N P R Mass Contact Barrel L1L2min. g 3,35 0,45 0,89 1,34 1,98 2,62 1,73 20 22 3,05 0,15 0,84 1,29 1,93 2,54 1,52 1,35 0,30 4.2 Material, protective plating Body material: copper alloy Protecti

26、ve plating: selective protection not permitted; minimum gold thickness: 1,27 m nickel undercoat 4.3 Permissible cables See Table 2. Table 2 Size Size of conductors Section insulation Contact Barrel AECMA Code mm2AWG amax. Rated test current A 20 22 004 0,4 22 1,25 5 aAWG: American Wire Gauge. 4.4 Ca

27、ble stripping See Table 3. Table 3 Size Stripped length of cable mm Contact Barrel 0,3 20 22 2,3 4.5 Tooling Conform to MIL-DTL-22520 and MIL-I-81969 See Table 4. EN 3155-045:20067 Table 4 Size Cable size Crimping tool Extraction tools Contact Barrel AECMA Code AWG aTool Positioner Selector number I

28、nsertion tool Wired contact Unwired contact 20 22 004 22 M22520/1-01M22520/1-02 red 4 MIL-I-81969/14-11 MIL-I-81969/14-11 MIL-I-81969/30-05aAWG: American Wire Gage. 4.6 Tests See Table 5. Table 5 Applicable EN 2591- Title Not applicableAccording to EN 3155-001 Remarks as on all other specs 101 Visua

29、l examination X 102 Examination of dimensions and mass X 201 Contact resistance - Low level X 202 Contact resistance at rated current X 204 Discontinuity of contacts in the microsecond range X 206 Measurement of insulation resistance X 207 Voltage proof test X 210 Electrical overload X 211 Capacitan

30、ce X 212 Surface transfer impedance X 213 Shielding effectiveness from 100 MHz to 1 GHz X 301 Endurance at temperature X T = (260 2) C Duration: 1 000 h 305 Rapid change of temperature X TA= (260 2) C TB= ( 65 2) C 306 Mould growth X 307 Salt mist X 315 Fluid resistance X 402 Shock X 403 Sinusoidal

31、and random vibration X 406 Mechanical endurance X 415 Test probe damage (female contact) X 416 Contact bending strength X continued EN 3155-045:20068 Table 5 (concluded) Applicable EN 2591- Title Not applicable According to EN 3155-001 Remarks as on all other specs 417 Tensile strength (crimped conn

32、ection) X Crimping of jacket shall be inoperative. 418 Gauge insertion/extraction forces (female contacts) X 502 Restricted entry X 503 Contact deformation after crimping X 508 Measurement of thickness of coating on contacts X The measured thickness shall be recorded. 509 Adhesion of coating on cont

33、acts X 513 Magnetic permeability X 2 4.7 Gauges See EN 3155-001 Table 2, tests EN 2591-415, EN 2591-418 and EN 2591-502. 5 Designation EXAMPLE Description block CONTACT, ELECTRICAL Identity block EN3155-045F2022 Number of this standard Type of contact F = female Contact size code (see Table 1) Barre

34、l size code (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 6 Marking See EN 3155-001. 7 Technical specification See EN 3155-001. EN 3155-045:2006blankBS EN 3155-045:2006BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards I

35、nstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards s

36、hould make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical commi

37、ttee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrder

38、s for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it i

39、s BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters

40、Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments

41、and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards On

42、line can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Cop

43、yright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the

44、 standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.