EN 1918-5-1998 0494 Gas Supply Systems - Underground Gas Storage - Part 5 Functional Recommendations for Surface Facilities《燃气供应系统 地下燃气储存 第5部分 表面设备的功能推荐规范》.pdf

《EN 1918-5-1998 0494 Gas Supply Systems - Underground Gas Storage - Part 5 Functional Recommendations for Surface Facilities《燃气供应系统 地下燃气储存 第5部分 表面设备的功能推荐规范》.pdf》由会员分享，可在线阅读，更多相关《EN 1918-5-1998 0494 Gas Supply Systems - Underground Gas Storage - Part 5 Functional Recommendations for Surface Facilities《燃气供应系统 地下燃气储存 第5部分 表面设备的功能推荐规范》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、- STD-BSI BS EN 19LB-5-ENGL 1778 m Lb24bb7 0708302 118 m BRITISH STANDARD Gas supply systems - Underground gas storage - Part 5: Functional recommendations for surface facilities * * M The European Standard EN 19185 1998 has the status of a British Standard ICs 75.200 NO COPYING WTHOUT BSI PERMISSIO

2、N EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 1918-5: 1998 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STD-BSI BS EN L9L-5-ENGL 1998 9 lb2Libb9 0708303 05Li m Amd. No. BS EN 1

3、91 - present to the responsible European committee any enquiries on the inteqmtalion, or propouals for change, and keep the K interests informed; - monitor related intemational and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be ob

4、tained on request to its secretary. Cross-references The British Standmis which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Inkmatioral Standards Correspondence index”, or by using the “Find” fa

5、cility of the BSI Standards Electronic catalogue. A British StanM does not purport to include all the necessary provisions of a conkact Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligatio

6、ns. Summary of pages This document comprises a front cover, an inside front cover, the EN titie page, pages 2 to 7 and a back cover. Q BSI 1998 ISBN O 680 29664 4 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permit

7、ted without license from IHS-,-,-EUROPEAN mmm NORME EUROPENNE EUROP- NORM EN 19185 February 1998 ICC 75.200 Descriptors: Storage, natural gas, gas installation, design, equipment specifications, performance evaluation, safety, environmental protection, fire protection, explosion proofing, tests, ope

8、rating requirements, maintenance English version Gas supply systems - Undewund gas storage - Part 5 Functiod recommendations for surface fxilities Systme dalimentation en gaz - Stockage Partie 5 Recommandations fonctionnelles pour les installatons de surface ertageadagen Gasvemxgwgsyskme - Untertage

9、Speicherung Teil 5: Funktionale Empfehlungen fur souterrain de gaz - VO Gas- This European Standard was approved by CEN on 22 January 1998. CEN members are bound to comply with the CEN/CENELEC internal Regulations which stipuiate the conditions for giving this European Standard the status of a natio

10、nal standard without any alteration. Up-to-date lists and bibliographicai references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any

11、 other language made by translation under the responsibility of a CEN member into its own language and notified to the CenM Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Gennany,

12、Greece, Iceland, Ireland, Itazmctional recmrnendut.ions for storage in rock caverns Part 5 Functional recommendations for sui facu.t.ies Contents Foreword Introduction 1 Scope 2 General description 2.1 Fillingfacilities 2.2 WlthdraWd facilities 2.3 Utilities 3 Design 4 Construction 5 Testingandcommi

13、ssioning 6 Operation and maintenance Annex A (informative) Bibliography page 2 3 3 3 3 3 4 4 5 6 6 7 ther relevant standards are listed in annex k According to the CEN/CENELEC Internai Regulations, the nationa standards oqpnimtions of the following countries are bound to implement this European Stan

14、dard: Aushia, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, It - a line pipe from the leaching water oftake staiion(s) to the leaching plane - water reservoirs or tanks; - water iqjection pumps and iters; - a lhe pipe from the leaching plant to the well head(s

15、); - a system for brine discharge with - a line pipe for brine discharges; - brine discharge pumps, iters and dispersers; - blanket fluid storage, item and pumps at the leaching plane - a line pipe for the blanket fluid from the leaching plant to the weUhead(s); - separation equipment for the remova

16、l of blanket fluid from brine; - a system for ensuring the safety of the facility including a shutdown system; - equipment for process control. A system for ensurhg the safety of the facility during the fmt gas nIling shall be provided. - a system for cavity roof protection with 3 Design 3.1 Safety

17、and environmental issues The design of the plant chdl enable the operator to conduct its operations in such a way as to minimize the risk of ham to its employees, contractom and all othem who may be affected directly or indiredy by its activities, and to comply with standards on safety, occupational

18、 health and environmental protection. For this, the following should be taken into consideration at the design stage: - selection of the least harmful process materials and intermediaries; muumization of the inventory of hazardous mmmwation of emissions of harmful solid, liquid . - 7 . - and gaseous

19、 substances; - design of combustion plant and equipment such as gas turbines, diesel and petrol engines, fiares and boilem to produce exhaust gas which conforms to the authorized emission contents for oxides of nitrogen and sulfur and other polutants; - location of plant to minimize the risk to neig

20、hbow and their propem 0 BSI 1998 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* rn * - setting out and, if nec-, protection of sections of plant so that an incident in one loc

21、ation does not escalate to another past of the site; - protection of the ground, in areas where hannfui liquids could be spilt, by an appropriate impervious sealing material with an appropriate and impervious retaining kerb. Spills shall be directed to tight catchment pits which are not directly con

22、nected to the main rainage system, watercourses or the sea; - provision for the treatment of liquid discharges to drcunage systems, water courses or the sea to render them harmiess or for their storage in tight tanks before removal. Contaminant levels shall not be greater than that for which a disch

23、arge consent has been granted; -disposai of harmfui spills in a safe and environmentaliy acceptable manner; - safe and environmentally acceptable storage of materials; - a leak and fire detection and fire protection system for plant, equipment and buildings where the consequences of an incident coul

24、d escalate and result in unacceptable consequences; - the need for fiameproof andor explosion-proof equipment in certain areas; - monitoring of safety and environmental performance throughout the life of the project; - the use of suitable safety anaysis techniques during the design phase; - the need

25、 to close certain valves from a remote location, such as the main control room or the weilhead compound, and for automatic emergency shutdown systems; - the effect of the storage facility on outside facilities such as railways, roads and public buildings, and vice versa, in order to determine the sa

26、fety distances. 3.2 Engineering Constniction materials for piping, vessels and ancillary equipment shall be chosen considering the most severe operating conditions. These may include gas composition, maximum wellhead static and dynamic pressure, operational temperature variations and minimum depress

27、urization temperatures if applicable. Above ground pipework shall be properly anchored and supported to withstand anticipated external forces. A sufficient number of valves shall be installed at strategic locations to enable sections to be isolated during routine testing and maintenance, and in an e

28、mergency. 3.3 Security Arrangements shaU be made to prevent the entry, either intentional or unintentional, of unauthorized persons to the central processing and remote weilhead Conventionally, this is achieved at the central processing area by security fencing with a single point of access which is

29、 controlled by a monitoring system. For emergency evacuation, exits may be provided in the fence at strategic locations. areas. Page 5 EN 191 - hazardous materials shall be stored, used and tramsported in a safe and environmentally acceptable manner. Provision shall be made to collect and contain an

30、y spill of hasmful material and to either render it harmless or have it disposed of in an acceptable manner; - site tsaffc management shall conform to that required by the planning consent. O BSI 1998 Copyright European Committee for Standardization Provided by IHS under license with CENNot for Resa

31、leNo reproduction or networking permitted without license from IHS-,-,- STD-BSI BS EN 1918-5-ENGL 1998 1b24bb9 0708309 572 Page 6 EN 19186:1998 5 !ksting and commissioning The criteria for safety and environmental issues given in clause 4 appiy in the testing and commissioning stage. In addition, du

32、ring commissioning and testing, procedures written by a competent person shall be followed to ensure the safety of personnel and protection of the environment. Before the piant and equipment is formally released to the operator, a procedure shall be followed to ensure that the completed plant has be

33、en constructed according to the designers intent, and that all the documentation needed by the operator is available. Plant and equipment should not be accepted unless it is accompanied by the correct certification and documentation in accordance with the relevant Quality assurance standard Plant an

34、d equipment shall be tested to demonstrate that they operate in accordance with the design. Est procedures described in European or other internationally or nationally recognized standards and codes should be used. 6 Operation and maintenance The plant shall be oped and maintained in accordance with

35、 the design. Specific procedures should be provided to ensure safety and proper environmental management of the plant Written operating and maintenance procedures shall be available. Modifications to plant and equipment, systems and procedures shall be designed and carried out by competent persons w

36、ithout reducing the level of safety. Plant and equipment shall be maintained so that emission levels do not increase above design iimits. Routine visual inspections shall be conducted to check the intern of plant and equipment. The operating company shall establish a tminhjj and review programme to

37、ensure the competence of operatjng stf. O BSI 1998 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- STD-BSI BS EN 3718-5-ENGL 3778 1b24bb7 0708330 294 Page 7 EN 19185:1998 Annex

38、A (informative) Bibliography prEN 1594, Gas supply systems - Pipelines - Maximum operating pressure over 16 bar - Functional requirements. prEN 12732, Gas supply systems - Welding steel pework - Functid requirements. prEN 1776, Functional requimts for gas metering systems for natural gas - Design, m

39、aterials, construction, reliability, calibration, operation and maintenance. prEN 12186, Gas pressure regwhting statim for tmnsrnission and distribution. prEN 12583, Compressor stations for gas supply systems. prEN 12327, Fressure testing, commissioning ami decommissioning procedures for gas supply

40、systems. * * u O BSI 1998 Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN 191&5:1998 BSI 389ChiswickHighRoad London w4 4AL BSI - British Standards Institution BSI is the in

41、dependent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that

42、they possess the latest amendments or editions. It is the constant aim of BSI to improve the ty of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the ide

43、ntity of which can be found on the inside hnt cover. Tel 0181 996 9OOO. Fax: 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standarh. Buying standards Orders for all BSI, international and forei

44、gn standards publications should be addressed to Customer Services. Tel 0181 996 7000. Fax 0181 996 7001. In response to orders for intemational standards, it is BSI policy to supply the MI implementation of those that have been published as British Standards, unless otherwise requested Information

45、on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Inf

46、ormation Centse. Tel 0181 996 7111. Fax 0181 996 7048. Subscribmg members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel 0181 996 7002. Fax 018

47、1 996 7001. - Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the K, of the publications of the intemational standarMon bodies. Except as permitted under the Copyright, Designs and Fatents Act 1988 no extract may be reproduced, stored m a retrieval system or tr

48、ansmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written pennission from BSI. This does not preclude the free use, in the com of implementing the stanard, of necessary details such as symbois, and size, type or grade designations. If these deta

49、ils are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained if pennission is granted, the terms may include royaity payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 0181 996 7070. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted wi