IEC 62037-4-2012 Passive RF and microwave devices intermodulation level measurement - Part 4 Measurement of passive intermodulation in coaxial cables《无源无线电频率(RF)和微波器件 内调水平测量.第4部分 同轴电缆中的无源互调测量》.pdf

《IEC 62037-4-2012 Passive RF and microwave devices intermodulation level measurement - Part 4 Measurement of passive intermodulation in coaxial cables《无源无线电频率(RF)和微波器件 内调水平测量.第4部分 同轴电缆中的无源互调测量》.pdf》由会员分享，可在线阅读，更多相关《IEC 62037-4-2012 Passive RF and microwave devices intermodulation level measurement - Part 4 Measurement of passive intermodulation in coaxial cables《无源无线电频率(RF)和微波器件 内调水平测量.第4部分 同轴电缆中的无源互调测量》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62037-4 Edition 1.0 2012-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Passive RF and microwave devices, intermodulation level measurement Part 4: Measurement of passive intermodulation in coaxial cables Dispositifs RF et micro-ondes passifs, mesure du niveau dintermodulation Partie 4: Mesure

2、de lintermodulation passive dans les cbles coaxiaux IEC 62037-4:2012-07(EN-FR) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elect

3、ronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please c

4、ontact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y c

5、ompris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit na

6、tional de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publis

7、hes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. I

8、EC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - ww

9、w.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new I

10、EC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French,

11、 with equivalent terms in 14 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publicati

12、ons issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.

13、ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publi

14、cations IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spc

15、ifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comi

16、t dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois

17、 par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 14 langues additionnelles. Egalement appel Vocabulaire Electr

18、otechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 55 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publicati

19、ons des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 62037-4 Edition 1.0 2012-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Passive RF and microwav

20、e devices, intermodulation level measurement Part 4: Measurement of passive intermodulation in coaxial cables Dispositifs RF et micro-ondes passifs, mesure du niveau dintermodulation Partie 4: Mesure de lintermodulation passive dans les cbles coaxiaux INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMIS

21、SION ELECTROTECHNIQUE INTERNATIONALE K ICS 33.040.20 PRICE CODE CODE PRIX ISBN 978-2-8322-1347-6 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorize

22、d distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 62037-4 IEC:2012 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references . 5 3 Abbreviations . 5 4 Test fixtures . 5 5 Procedure. 7 5.1 General . 7 5.2 Dynamic test procedure Clamped ca

23、ble loop 8 5.3 Dynamic test Flexing tool . 8 5.4 Static test 9 Annex A (informative) General test considerations 10 Figure 1 Dynamic test using clamped “U“ bend in cable . 6 Figure 2 Dynamic test using flexing tool . 6 Table 1 Dimensions of the flexing tool 7 Table 2 Groove diameter . 7 62037-4 IEC:

24、2012 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ PASSIVE RF AND MICROWAVE DEVICES, INTERMODULATION LEVEL MEASUREMENT Part 4: Measurement of passive intermodulation in coaxial cables FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comp

25、rising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Stan

26、dards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this prep

27、aratory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organ

28、izations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form

29、of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretati

30、on by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regi

31、onal publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out

32、by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees

33、for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the N

34、ormative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held re

35、sponsible for identifying any or all such patent rights. International Standard IEC 62037-4 has been prepared by technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. This bilingual version (2014-01) corresponds to the monolingual

36、English version, published in 2012-07. The text of this standard is based on the following documents: FDIS Report on voting 46/418/FDIS 46/434/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of

37、 this standard has not been voted upon. 4 62037-4 IEC:2012 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all the parts in the IEC 62037 series, published under the general title Passive r.f. and microwave devices, intermodulation level measurement can

38、 be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed,

39、 withdrawn, replaced by a revised edition, or amended. 62037-4 IEC:2012 5 PASSIVE RF AND MICROWAVE DEVICES, INTERMODULATION LEVEL MEASUREMENT Part 4: Measurement of passive intermodulation in coaxial cables 1 Scope This part of IEC 62037 defines test fixtures and procedures recommended for measuring

40、 levels of passive intermodulation generated by coaxial cables. Two dynamic test methods and a static test method are defined. All coaxial cables are subjected to the static and clamped cable loop dynamic test. Cables classified as flexible or semi-flexible are additionally subjected to the flexing

41、tool dynamic test. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (

42、including any amendments) applies. IEC 62037-1, Passive r.f. and microwave devices, intermodulation level measurement Part 1: General requirements and measuring methods IEC 62037-3, Passive r.f. and microwave devices, intermodulation level measurement Part 3: Measurement or passive intermodulation i

43、n coaxial connectors 3 Abbreviations DUT Device under test IM Intermodulation 4 Test fixtures For the dynamic tests, appropriate test fixtures are required. For the clamped cable loop test (see 5.2), a method shall be provided for laterally moving the cable and for clamping the cable each side of th

44、e region of movement, as shown schematically in Figure 1. Design of the clamps shall be such as to firmly support the cable at the required points without causing damage to the cable by crushing or kinking. In the moving test using the flexing tool (see 5.3), the cable is flexed by a fixture through

45、 which the cable is threaded as shown in Figure 2. General design for the fixture is shown in Figure 2, and the detailed dimensions for different cable sizes (and different specified bend radii) are listed in Table 1 and Table 2. 6 62037-4 IEC:2012 Clamp R R Clamp To load To test set d3d3d1d1d2d2IEC

46、 1535/12 Figure 1 Dynamic test using clamped “U“ bend in cable Y X + D X R = D Clamps DUT Test port Z IEC 1536/12 Figure 2 Dynamic test using flexing tool 62037-4 IEC:2012 7 D is equal to or greater than the nominal diameter of the cable under test. Values X, Y and Z depend on minimum bend radius of

47、 the cable for repeated bending. Table 1 Dimensions of the flexing tool D diameter of the cable R_min Minimum bend radius of the cable for repeated bending X See Table 2 Y 2 R_min Z X + 2,5 cable diameter Table 2 Groove diameter Minimum bending radius of cable under test Groove diameter X mm R_min 3

48、3 mm 66 33 mm R_min 47 mm 94 47 mm R_min 68 mm 136 68 mm R_min 100 mm 200 Other values may be used if agreed upon by the customer and supplier or specified by the manufacturer. 5 Procedure 5.1 General The test method of IEC 62037-1 shall be used. Intermodulation in long cables is measured using the

49、reverse set-up because of the significant attenuation of these cables. If the cable to be measured is long enough, i.e. with a one-way insertion loss of 10 dB or greater, it is required only to connectorize the end to be tested. Use connectors with known low IM performance relative to the DUT. Soldered joints are preferred. Similarly, if a termination is required, this shall also be of kno