EN 1814-2005 en Textile floor coverings - Determination of resistance to damage at cut edges using the modified Vettermann drum test《铺地织物 改良的维特曼(Vettermann)鼓试验用抗切边损坏的测定》.pdf

《EN 1814-2005 en Textile floor coverings - Determination of resistance to damage at cut edges using the modified Vettermann drum test《铺地织物 改良的维特曼(Vettermann)鼓试验用抗切边损坏的测定》.pdf》由会员分享，可在线阅读，更多相关《EN 1814-2005 en Textile floor coverings - Determination of resistance to damage at cut edges using the modified Vettermann drum test《铺地织物 改良的维特曼(Vettermann)鼓试验用抗切边损坏的测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 1814:2005Textile floor coverings Determination of resistance to damage at cut edges using the modified Vettermann drum testThe European Standard EN 1814:2005 has the status of a British StandardICS 59.080.60g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40

2、g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 1814:2005This British Standard was published under the authority of the Standards Policy and Strategy Committee on 27 October 2005 BSI 27 October 2005ISBN 0 580 4672

3、6 0National forewordThis British Standard is the official English language version of EN 1814:2005. It supersedes BS EN 1814:1998 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/3, Textile floor coverings, which has the responsibility to:A list of

4、organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Corr

5、espondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard does not o

6、f itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and

7、 promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 11 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date

8、CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1814August 2005ICS 59.080.60 Supersedes EN 1814:1997 English VersionTextile floor coverings - Determination of resistance to damageat cut edges using the modified Vettermann drum testRevtements de sol textiles - Dtermination de larsistance de

9、s joints par lessai au tambour VettermannmodifiTextile Bodenbelge - Bestimmung derSchnittkantenfestigkeit durch modifizierte Trommelprfungnach VettermannThis European Standard was approved by CEN on 22 July 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulat

10、e the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists i

11、n three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of

12、Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARD

13、IZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2005 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1814:2005: EEN 1814:2005 (E) 2 Contents Page Foreword 3 1

14、Scope. 4 2 Normative references. 4 3 Terms and definitions 4 4 Principle 5 5 Apparatus 5 6 Sampling and preparation of specimens6 7 Atmosphere for conditioning and testing. 10 8 Procedure 10 9 Assessment 10 10 Test report. 11 EN 1814:2005 (E) 3 Foreword This European Standard (EN 1814:2005) has been

15、 prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 200

16、6, and conflicting national standards shall be withdrawn at the latest by February 2006. This document supersedes EN 1814:1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, B

17、elgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 1814:2005 (E) 4 1 Scope This docume

18、nt specifies a method to determine the susceptibility of textile floor coverings to mechanical damage at cut edges. It is applicable to all textile floor coverings both as sheet materials and as tiles. 2 Normative references The following referenced documents are indispensable for the application of

19、 this European Standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1471, Textile floor coverings Assessment of changes in appearance EN 20139, Textiles Standard atmospheres for co

20、nditioning and testing (ISO 139:1973) ISO 1957, Machine-made textile floor coverings Selection and cutting of specimens for physical tests ISO 10361:2000, Textile floor coverings Production of changes in appearance by means of Vettermann drum and hexapod tumbler testers 3 Terms and definitions For t

21、he purposes of this European Standard, the following terms and definitions apply. 3.1 delamination separation of the use-surface and/or foundation/primary substrate of a textile floor covering from the secondary substrate or foam backing 3.2 fraying loss of pile or substrate material of a textile fl

22、oor covering from a cut edge 3.3 tufting out loss of tufts from the use-surface of a textile floor covering 3.4 sprouting release and appearance during use of extra long tuft legs that were accidentally trapped within the pile of a textile floor covering during manufacture 3.5 laddering; shooting lo

23、ss of consecutive loops of the same column from the use-surface of a textile floor covering EN 1814:2005 (E) 5 4 Principle A metal ball with six rubber studs rolls freely inside a rotating drum that is lined with the textile floor-covering specimens. On sheet materials, a cut is made along the lengt

24、h of the specimens at an acute angle such that the cut edges are stressed in the test. Tiles are put together so that the original edges of the tiles form the joint, which is stressed in the test. After the test, the appearance of the fatigued cut edges is assessed. 5 Apparatus 5.1 Drum tester, conf

25、orming to 5.1.1 of ISO 10361:2000, including a vacuum cleaner with an air change rate at the nozzle of 25 l/s to 40 l/s shown in Figure 1. 730 101 23456Key 1 Extraction of brushed fibres 4 Rubber stud 2 Circular brush 5 Fixing plate in vulcanized fibre 3 Metal drum 6 Steele ball (see Figure 2) Figur

26、e 1 Vettermann drum EN 1814:2005 (E) 6 5.2 Metal ball, fitted with six cylindrical rubber studs equally spaced from each other on the surface of the ball as shown in Figure 2. Dimensions in millimetres Key 1 Ball Figure 2 Ball The mass of the ball without rubber studs shall be 7 000 g 100 g and the

27、diameter of the ball shall be 120 mm 0,2 mm. 5.3 Rubber studs, conforming to ISO 10361, which shall be replaced before each test. 5.4 External vacuum cleaner, upright type with rotating brush. 6 Sampling and preparation of specimens 6.1 Sampling 6.1.1 General Sampling shall be carried out in accorda

28、nce with ISO 1957. EN 1814:2005 (E) 7 6.1.2 Sheet materials Prepare four specimens approximately 570 mm long (in the direction of manufacture) and approximately 265 mm wide. The longitudinal edge of the specimens shall be parallel to the direction of manufacture. EN 1814:2005 (E) 8 6.1.3 Tiles Take

29、at least four tiles of dimensions 500 mm 500 mm or of lesser dimensions. Before cutting, mark the corners of the tiles and the direction of manufacture on the back of the specimen as shown in Figure 3. From the tiles cut a total of eight specimens of width approximately 132 mm, as shown in Figure 3.

30、 Dimensions in millimetres B ACBA132 132 132 132D132132132 132D CFigure 3 Specimen preparation by cutting of tiles EN 1814:2005 (E) 9 6.2 Preparation of specimens 6.2.1 Sheet materials Make a cut in the centre of the specimens making an acute angle with the direction of manufacture (see Figure 4). T

31、he cut shall cross at least one pile row. The cut shall be made with a sharp cutting tool (carpet knife or a press cutter), cutting from the pile side through the pile and backing. Connect the two sides of the cut specimens on the back with a single-sided adhesive tape of at least 50 mm width. Apply

32、 the adhesive tape firmly. Ensure that the two edges are as close as possible. Attach double-sided adhesive tape along the entire specimen length and positioned over the single-sided tape. Cover both ends of the specimens with a 50 mm wide single-sided adhesive tape to prevent fraying during the tes

33、t. If necessary remove frayed and sprouting parts of damaged tufts with a sharp cutting tool. NOTE If the seams are sealed with seaming cement in practise then they can also be sealed with a seaming cement on the test specimens. Dimensions in millimetres 1012020Key 1 Cut Figure 4 Setting of the cut

34、in specimens of sheet materials 6.2.2 Tiles Prepare four specimens of each floor covering as shown in Figure 3, two to test the edges in the direction of manufacture (pieces A and B) and two in the transverse direction (pieces C and D). Make up four composite test specimens with the original cut edg

35、e in the centre. Position the edges in the centre of the specimen as close to each other as possible and fix in position with the single-sided adhesive tape. EN 1814:2005 (E) 10 Attach double-sided adhesive tape along the entire specimen length and position over the single-sided tape. If necessary r

36、emove frayed and sprouting parts of damaged tufts with a sharp cutting tool. 7 Atmosphere for conditioning and testing Condition the specimens (face up) in the standard atmosphere for textiles, as defined in EN 20139, for at least 24 h. Conduct the test in this atmosphere. 8 Procedure Remove the pro

37、tective layer from the double-sided adhesive tape on the back of the specimen. Fix the four specimens on the inside of the drum with the use-surface towards the centre of the drum. In placing the specimens, ensure that the sides lie within the retaining segments. Insert the specimens between the ret

38、aining segments and clamp firmly. Place the ball (5.2) in the drum. Set the revolution counter to 11 000 cycles and switch the machine on. Operate the vacuum continuously throughout the test. After the test, clean the specimens with the external vacuum cleaner with rotating brush, making four passes

39、 in each direction along the length of the specimen, the last pass being in the direction of pile lay. 9 Assessment Place the specimen on the rotating observation table as defined in EN 1471 and use the observation conditions specified in EN 1471. Make sure the specimens lay perfectly flat, especial

40、ly in the cut area. Check for degradation of the cut edges by the fatiguing action in the test. Note the type of damage as defined in Clause 3, in particular if fibres or yarns are pulled out on to the surface, and, if so, from which part of the floor covering they originate (pile or substrate). Che

41、ck by close inspection under the observation conditions specified in EN 1471 whether there has been delamination, and, if so, the length and width of each delaminated area. Check by close inspection under the observation conditions specified in EN 1471 the number of yarns pulled out with a length gr

42、eater than one loop (loop pile products). The floor covering is considered to be resistant to fraying when none of the specimens show delamination with more than 30 mm length and more than 10 mm depth and not more than 1 out of 4 specimens shows an unacceptable degradation. Following damage is consi

43、dered to be unacceptable: visible tuft out (tuft out of tufts or loops cut during specimen preparation is not to be taken into consideration when assessing tuft out); EN 1814:2005 (E) 11 loops pulled out with a length greater than one loop. 10 Test report The test report shall state: a) reference to

44、 this document, i.e. EN 1814; b) identification of the product tested, including the type, origin, manufacturers reference number; c) sampling details; d) the result of the test, as in Clause 9; e) details of any deviations from this standard procedure that might have an influence on the results. BS

45、 EN 1814:2005BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Sta

46、ndards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while usin

47、g this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers aut

48、omatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website

49、at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information C