EN 1621-1-2012 en Motorcyclists- protective clothing against mechanical impact - Part 1 Motorcyclists- limb joint impact protectors - Requirements and test methods《摩托车手的防护服对机械冲击-第1.pdf

《EN 1621-1-2012 en Motorcyclists- protective clothing against mechanical impact - Part 1 Motorcyclists- limb joint impact protectors - Requirements and test methods《摩托车手的防护服对机械冲击-第1.pdf》由会员分享，可在线阅读，更多相关《EN 1621-1-2012 en Motorcyclists- protective clothing against mechanical impact - Part 1 Motorcyclists- limb joint impact protectors - Requirements and test methods《摩托车手的防护服对机械冲击-第1.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 1621-1:2012Motorcyclists protectiveclothing against mechanicalimpactPart 1: Motorcyclists limb joint impactprotectors Requirements and testmethodsBS EN 1621-1:2012 BRITISH

2、STANDARDNational forewordThis British Standard is the UK implementation of EN 1621-1:2012. Itsupersedes BS EN 1621-1:1998 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PH/3/9, Motorcyclists Personal Protective Equipment.A list of organizations represe

3、nted on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 705

4、55 7ICS 13.340.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 28 February 2013.Amendments issued since publicationDate Text affectedBS EN 1621-1:2012EUROPEAN ST

5、ANDARD NORME EUROPENNE EUROPISCHE NORM EN 1621-1 December 2012 ICS 13.340.10 Supersedes EN 1621-1:1997English Version Motorcyclists protective clothing against mechanical impact - Part 1: Motorcyclists limb joint impact protectors - Requirements and test methods Vtements de protection contre les cho

6、cs mcaniques pour motocyclistes - Exigences et mthodes dessai des protecteurs - Partie 1: Exigences et mthodes dessai Motorradfahrer-Schutzkleidung gegen mechanische Belastung - Teil 1: Gelenkprotektoren fr Motorradfahrer - Anforderungen und Prfverfahren This European Standard was approved by CEN on

7、 27 October 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards ma

8、y be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified

9、to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland

10、, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: A

11、venue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1621-1:2012: EBS EN 1621-1:2012EN 1621-1:2012 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope .5 2 Normative references 5 3 Terms and defi

12、nitions .5 4 Zones of protection and protectors6 5 Requirements 6 5.1 General 6 5.2 Innocuousness 6 5.3 Minimum dimensions of zone of protection 6 5.4 Impact attenuation 7 5.5 Ergonomic requirements 8 6 Test methods and equipment .8 6.1 General 8 6.2 Innocuousness 8 6.3 Impact attenuation 8 6.3.1 Eq

13、uipment .8 6.3.2 Sampling 10 6.3.3 Positioning of the sample . 11 6.3.4 Impact Tests 11 6.4 Ergonomic assessment 12 6.5 Procedure 12 6.6 Expression of test results . 13 6.7 Test report . 13 7 Marking 13 8 Information supplied by the manufacturer. 14 Annex ZA (informative) Relationship between this E

14、uropean Standard and the Essential Requirements of EU Directive 89/686/EEC . 16 Figures Figure 1 Definition of the zone of protection by three key dimensions . 7 Figure 2 Anvil . 9 Figure 3 Template with indication of the test areas 10 Figure 4 Example of marking of a protector according to Clause 7

15、, list entry d) . 14 Tables Table 1 Minimum dimensions of zone of protection . 7 Table 2 Transmitted force and performance levels 7 Table 3 Minimum number of samples and impacts required 11 Table ZA.1 Correspondence between this European Standard and Directive 89/686/EEC 16 BS EN 1621-1:2012EN 1621-

16、1:2012 (E) 3 Foreword This document (EN 1621-1:2012) has been prepared by Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either b

17、y publication of an identical text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC

18、 shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1621-1:1997. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(

19、s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. The main technical changes with respect to the 1997 edition are listed below: a) the scope has been restricted only to limb joint impact protectors; b) requirements concerning innocuousne

20、ss have been added; c) requirements concerning the wet impact test (mandatory) and the high and low temperature impact tests (optional) have been added; d) ergonomic requirements have been added. EN 1621 consists of the following parts, under the general title Motorcyclists protective clothing again

21、st mechanical impact: Part 1: Motorcyclists limb joint impact protectors Requirements and test methods (the present document) Part 2: Motorcyclists back protectors Requirements and test methods Part 3: Requirements and test methods for chest protectors1) Part 4: Motorcyclists inflatable protectors R

22、equirements and test methods According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Repub

23、lic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. 1) Under development. BS EN 1621-1:2012EN 1621-1:2012 (E)

24、4 Introduction This European Standard is Part 1 of a standard containing requirements and test methods for motorcycle riders impact protectors. Impact protectors meeting the requirements of this European Standard will provide some protection against injury caused by impacts with road surfaces in mot

25、orcycle accidents. They may also slightly reduce the injuries caused by impacts with objects such as other vehicles. In order to encourage the adoption of certified protection by the highest possible number of users, two performance levels are specified for protectors. These are level 1 for protecto

26、rs designed to give protection whilst having low ergonomic penalties associated with its use and level 2 for protectors providing an increased protection with respect to level 1. There may be, however, weight and restriction penalties associated with level 2 protection. BS EN 1621-1:2012EN 1621-1:20

27、12 (E) 5 1 Scope This European Standard specifies requirements and test methods for limb joint impact protectors incorporated or intended to be incorporated into motorcycle riders clothing or used as separate items. 2 Normative references The following documents, in whole or in part, are normatively

28、 referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 340, Protective clothing General requirements EN ISO 105-E01, Tex

29、tiles Tests for colour fastness Part E01: Colour fastness to water (ISO 105-E01) EN ISO 11642, Leather Tests for colour fastness Colour fastness to water (ISO 11642) ISO 6487, Road vehicles Measurement techniques in impact tests Instrumentation 3 Terms and definitions For the purposes of this docume

30、nt, the following terms and definitions apply. 3.1 zone of protection specific area of the protective equipment that is intended to provide protection to a part of the body and which is subject to specific testing 3.2 protector arrangement of energy absorbing and/or impact spreading materials design

31、ed to offer some protection to the zones of protection 3.3 type A protector protectors of smaller dimension; these are more commonly (although not exclusively) optimised for use with smaller riders 3.4 type B protector protectors of larger dimension; these are more commonly (although not exclusively

32、) optimised for use with larger riders 3.5 test area area on which impact tests are performed; size and shape are defined by the template 3.6 template auxiliary tool made of flexible material used to verify the minimum area of protection BS EN 1621-1:2012EN 1621-1:2012 (E) 6 4 Zones of protection an

33、d protectors The following body regions are specified as zones of protection and protectors shall be categorised as follows: a) shoulder: protector “S”; b) elbow and forearm: protector “E”; c) hip: protector “H”; d) knee and upper tibia: protector “K”; e) knee, upper and middle tibia: protector “K +

34、 L”; f) leg below protector “K”: protector “L”. The size of the zones of protection shall comply with 5.3, Table 1. 5 Requirements 5.1 General Unless otherwise specified, all linear dimensions bigger than 50 mm in the whole text shall be provided with a deviation of 2 % and dimensions up to 50 mm wi

35、th a deviation of 1 mm. Limb joint protectors shall be provided with means of restraint capable of ensuring that the protector is maintained in position during use. This requirement is not applicable for protectors to be inserted or incorporated into the garments. Testing shall be carried out accord

36、ing to 6.4. 5.2 Innocuousness 5.2.1 The materials shall comply with the requirements for innocuousness of materials in EN 340, with the exception of the requirement concerning the colour fastness to perspiration which is replaced by 5.2.2. 5.2.2 The colour fastness to water of the constituent materi

37、als which could be likely to come into contact with the skin of the user shall be determined in accordance with 6.2 and shall be at least grade 4 of the Grey scale for the staining of any component of the multi-fibre reference fabric. 5.3 Minimum dimensions of zone of protection Motorcyclists limb j

38、oint protectors shall provide a zone of protection with the minimum dimensions as specified in Table 1. Testing shall be carried out as described in 6.3.4. In Table 1, the zones of protection are defined by the three dimensions r1, r2 and l, as illustrated in Figure1: BS EN 1621-1:2012EN 1621-1:2012

39、 (E) 7 Figure 1 Definition of the zone of protection by three key dimensions Table 1 Minimum dimensions of zone of protection Protector Type A protector mm Type B protector mm r1r2l r1r2l S 55 32 64 70 40 80 E 45 24 118 50 30 150 K 55 24 100 70 30 130 H 35 26 70 44 33 88 L 32 24 64 40 30 80 K + L 55

40、 24 185 70 30 240 5.4 Impact attenuation In terms of impact attenuation, this standard includes two performance levels. The degree of risk or hazards that a motorcyclist faces is closely linked to the type of riding and the nature of the accident. Level 1 performance is deemed as the minimum level r

41、equired so that the protector provides useful protection in an accident and offers the protector with an optimum comfort level to suit all riding types. Where riders feel that their riding style exposes them to an increased accident risk, Level 2 has been provided, which offers increased performance

42、. Level 2 may have an increased penalty for the weight and comfort. When impact protection is tested in accordance with 6.3.4.2 (ambient impact test), 6.3.4.3 (wet impact test after hydrolytic ageing) and, if required, 6.3.4.4 (high temperature impact test) and/or 6.3.4.5 (low temperature impact tes

43、t), the transmitted force shall conform to the values in Table 2. Level 1 or Level 2 can only be awarded provided that such level is achieved under all test conditions claimed. Table 2 Transmitted force and performance levels Level 1 Level 2 Overall mean value Single strike area Aa Single strike are

44、a Ba and Ca 35 kN 35 kN 50 kN 20 kN 20 kN 30 kN aAreas A, B and C correspond to the areas in Figure 3. BS EN 1621-1:2012EN 1621-1:2012 (E) 8 After each test, there shall be no fragmentation of the sample and no sharp edges shall be formed. However, formation of cracks and loss of soft debris is perm

45、issible. 5.5 Ergonomic requirements When examined and tested in accordance with 6.4, impact protectors shall be found satisfactory for the use intended; to confirm this requirement, each question of 6.5 needs to be answered with “yes”. The following deficiencies are not admitted: a) sharp edges; b)

46、any design feature which cause ergonomic problems to the assessor (see 6.4). 6 Test methods and equipment 6.1 General For each of the required sequences of measurements performed in accordance with this standard a corresponding estimate of the uncertainty of the final result shall be determined. On

47、request, this uncertainty (Um) shall be given in the test report in the form Um = X. It shall be used in determining whether a “Pass” performance has been achieved. If the final result plus Um is above the maximum Pass level, the sample shall be deemed to have failed. Measuring instruments or their

48、independent working components unless otherwise specified shall have an error limit of 4 % of the pass/fail level of the characteristic being measured. In the following subclauses both testing methods and equipment are described. 6.2 Innocuousness For colour fastness to water, materials of protectiv

49、e clothing shall be tested according to EN ISO 105-E01 for textiles and according to EN ISO 11642 for leather. 6.3 Impact attenuation 6.3.1 Equipment 6.3.1.1 Dropping apparatus The apparatus shall be such that a falling mass (“drop striker”) may be released in order to drop along a guided vertical path with an energy of (50 2) J onto the sample placed on a test anvil. The centre axis of the falling mass coincides with the centre axis of the anvil. 6.3.1.2 Drop striker The drop striker shall