EN 13409-2002 en Methods of Test for Hydraulic Setting Floor Smoothing and or Levelling Compounds - Determination of Setting Time《水压调整地面平滑和 或调平用复合物的试验法 调整时间测定》.pdf

《EN 13409-2002 en Methods of Test for Hydraulic Setting Floor Smoothing and or Levelling Compounds - Determination of Setting Time《水压调整地面平滑和 或调平用复合物的试验法 调整时间测定》.pdf》由会员分享，可在线阅读，更多相关《EN 13409-2002 en Methods of Test for Hydraulic Setting Floor Smoothing and or Levelling Compounds - Determination of Setting Time《水压调整地面平滑和 或调平用复合物的试验法 调整时间测定》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、Methods of test for hydraulic setting floor smoothing and/or levelling compounds Determination of setting time The European Standard EN 13409:2002 has the status of a British Standard ICs 91.100.99 BS EN 13409:2002 BS EN 13409:2002 Amd. No. National foreword Date Comments This British Standard, havi

2、ng been prepared under the direction of the Materials and Chemicals Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 15 April 2002 This British Standard is the official English language version of EN 13409:2002. The UKparticipa

3、tion in its preparation was entrusted to Technical Committee PRV52, Adhesives, which has the responsibility to: - - aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; mo

4、nitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this committee can be obtained on request to its secretary. Cr oss-r e fer enc e s The British Standards which implement international or European publications referred to in

5、 this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract.

6、Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 7 and a back cover. The

7、 BSI copyright date displayed in this document indicates when the document was last issued. O BSI 15 April 2002 ISBN O 580 39509X EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13409 March 2002 ICs 91.100.99 English version Methods of test for hydraulic setting floor smoothing and/or levelling

8、 compounds - Determination of setting time Mthodes dessai pour les mortiers de lissage et/ou dgalisation prise hydraulique - Dtermination du temps de prise Prfverfahren fr hydraulisch erhrtende Boden- Spachtelmassen - Bestimmung der Abbindezeit This European Standard was approved by CEN on 30 Decemb

9、er 2001 CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtain

10、ed on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centr

11、e has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EURO

12、PEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassart, 36 B-1050 Brussels O 2002 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13409:2002 E EN 13409:20

13、02 (E) Contents page Foreword 3 1 2 3 4 5 6 7 8 8.1 8.2 8.3 9 10 Scope 4 Normative references 4 Terms and definitions 4 Principle 4 Safety 4 Standard test conditions . 4 Apparatus and materials . 5 Procedure . 5 Calibration 5 Determination of initial setting time . 5 Determination of final setting t

14、ime . 6 Expression of results 7 Test report 7 2 EN 13409:2002 (E) Foreword This document EN 13409:2002 has been prepared by Technical Committee CEN/TC 193 “Adhesives“, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by public

15、ation of an identical text or by endorsement, at the latest by September 2002, and conflicting national standards shall be withdrawn at the latest by September 2002. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to impleme

16、nt this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 3 EN 13409:2002 (E) 1 Scope This European Standard specifies the measu

17、rement of setting time of a hydraulic setting smoothing and/or levelling compound which is referred to as ”smoothing and/or levelling compound”, after mixing. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative

18、 references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated referenc

19、es the latest edition of the publication referred to applies (including amendments). EN 196-3, Methods of testing cement - Part 3: Determination of setting time and soundness. EN 1937, Test method for hydraulic setting floor smoothing and/or levelling compounds - Standard mixing procedu- res. IS0 55

20、4, Standard atmospheres for conditioning and/or testing - Specifications. 3 Terms and definitions For the purposes of this European Standard, the following term and definition and those given in EN 1937 apply. 3.1 setting process of transition from plastic to solid state characterised by the initial

21、 and final penetration times 4 Principle The setting time is determined by observing the penetration of a needle into the smoothing and/or levelling compound mixture and recording the time for a given penetration value. 5 Safety Persons using this standard shall be familiar with normal laboratory pr

22、actice. This standard does not purport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish safety and health practices and to ensure compliance with any European or national regulatory conditions. 6 Standard test conditions The stand

23、ard test conditions shall be (23 f 2) OC and (50 f 5) % relative humidity in accordance with IS0 554. All test materials and apparatus shall be stored under these conditions for the duration of the test. The tests shall be carried out in an area where the air circulation is less than 0,2 m/s. 4 EN 1

24、3409:2002 (E) 7 Apparatus and materials 7.1 diameter (1 ,I3 f 0,051) mm, and attachment made from corrosion resistant metal. Vicat apparatus, in accordance with EN 196-3 (see Figure 1) with a steel needle, length (50 f 1) mm, The total mass of the moving parts shall be (300 f 1) g. Their movement sh

25、all be truly vertical on an axis coincident with the steel needle and without significant friction. 7.2 Mould (see Figure la), containing the mixture under test shall be made of hard rubber. It shall be of truncated conical form (40,O f 0,2) mm deep and shall have internal diameters at top and botto

26、m of (70 f 5) mm and (80 f 5) mm respectively. The apparatus shall be sufficiently rigid and placed on a plane glass plate larger than the mould and at least 2,5 mm thick. Moulds of metal or plastics or of cylindrical form can be used provided they are of the specified depth and that they can be sho

27、wn to give the same test results as the specified hard rubber mould of truncated conical form. 7.3 Timer, accurate to 1 s. 7.4 Smoothing andlor levelling compound, in accordance with EN 1937. 8 Procedure 8.1 Calibration Calibrate the Vicat apparatus (7.1) with the needle (see Figure 1 b), attached i

28、n advance of the test by lowering the needle to rest on the base plate to be used. Adjust the pointer to zero. Raise the needle to the stand-by position. 8.2 Determination of initial setting time Lightly grease the glass plate and the mould. When the standard mixing procedure is completed in accorda

29、nce with EN 1937, fill the mould immediately without undue compaction or vibration and start the timer. Using a straight edge implement remove the excess with a gentle sawing action to leave a flat smooth surface. Place the test specimen centrally under the needle. When the smoothing and/or levellin

30、g compound mixture is showing signs of setting lower the needle gently until it is in contact with the surface. Pause in that position for between 1 s and 2 s in order to avoid initial velocity or forced acceleration of the moving parts. Then release quickly and allow the needle to penetrate vertica

31、lly into the smoothing and/or levelling compound. Read the scale when penetration has ceased or after 30 s after the release of the needle whichever is earlier. Record the scale reading which indicates the distance between the end of the needle and the base plate together with the time from zero. Re

32、move and clean the needle. Reposition the test specimen so that the next point of penetration is at a distance greater than 10 mm from the edge or of any previous test. Repeat at conveniently spaced time intervals, e. g. 5 min. until the scale reading is (4 f 1) mm. Time intervals near the end point

33、 should be reduced to ensure that successive test results do not vary excessively. Record to the nearest minute the time at which this occurs together with any abnormalities such as separation. 5 EN 13409:2002 (E) Dimensions in millimetres 12 Key 1 Hard rubber mould 2 Platorm for correcting weights

34、3 Glass plate a) Side view with mould for setting time determinations b) needle for determination of setting time Figure 1 - Vicat apparatus for determining setting times 8.3 Determination of final setting time Continue with the procedure in 8.2 until the needle penetrates the compound by 0,5 mm. Ti

35、me intervals near the end point should be reduced to ensure that successive test results do not vary excessively. 6 EN 13409:2002 (E) Record to the nearest minute the time measured from zero at which the needle first penetrates only 0,5 mm into the test specimen. 9 Expression of results 9.1 mixture

36、to when the reading is (4 f 1) mm on the scale, rounded to the nearest minute. Express the initial setting time as the elapsed time between the end of the mixing procedure to prepare the 9.2 mixture to when the needle first penetrates only 0,5 mm into the mixture, rounded to the nearest minute. Expr

37、ess the final setting time as the elapsed time between the end of the mixing procedure to prepare the 10 Test report The test report shall include: a) a reference to this European Standard; b) the designation of the smoothing and/or levelling compound under test, the date of manufacture and/or batch

38、 number, if known; c) the proportions of the liquid components by mass in relation to 100 parts of powder component; d) the method of mixing the compound and the total time in minutes in accordance with EN 1937; e) the initial and final setting times, in minutes; f) any deviations from the specified

39、 test methods; g) date of test. 7 BS EN 13409:2002 BSI 389 Chiswick High Road Lon don w4 4AL BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re vi si

40、ons British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambi

41、guity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures tha

42、t subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: orders&-. Standards are also available from

43、 the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national,

44、European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 704

45、8. Email: infomi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details ofthese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: me

46、mbershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in t

47、he UK, ofthe publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise -witho

48、ut prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, ofnecessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission ofBSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyright&-.