EN 13329-2016 en Laminate floor coverings - Elements with a surface layer based on aminoplastic thermosetting resins - Specifications requirements and test methods (Incorporates Am.pdf

《EN 13329-2016 en Laminate floor coverings - Elements with a surface layer based on aminoplastic thermosetting resins - Specifications requirements and test methods (Incorporates Am.pdf》由会员分享，可在线阅读，更多相关《EN 13329-2016 en Laminate floor coverings - Elements with a surface layer based on aminoplastic thermosetting resins - Specifications requirements and test methods (Incorporates Am.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 13329:2016Laminate floor coverings Elements with a surfacelayer based on aminoplasticthermosetting resins Specifications, requirementsand test methodsBS EN 13329:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13329:2016.It su

2、persedes BS EN 13329:2006+A1:2008 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/60, Resilient and Laminate Floor Coverings.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not p

3、urport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 84168 2ICS 97.150Compliance with a British Standard cannot confer immunity fromlegal obligations

4、.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 March 2016.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 13329:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13329 March 2016 ICS 97.150 Supersede

5、s EN 13329:2006+A1:2008English Version Laminate floor coverings - Elements with a surface layer based on aminoplastic thermosetting resins - Specifications, requirements and test methods Revtements de sol stratifis - lments dont la surface est base de rsines aminoplastes thermodurcissables - Spcific

6、ations, exigences et mthodes dessai Laminatbden - Elemente mit einer Deckschicht auf Basis aminoplastischer, wrmehrtbarer Harze - Spezifikationen, Anforderungen und Prfverfahren This European Standard was approved by CEN on 27 November 2015. CEN members are bound to comply with the CEN/CENELEC Inter

7、nal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any

8、CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official ver

9、sions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

10、 Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitat

11、ion in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13329:2016 EBS EN 13329:2016EN 13329:2016 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 6 4 Requirements . 7 4.1 General requirements . 7 4.2 Classificat

12、ion requirements 8 4.3 Additional technical characteristics . 10 5 Marking and packaging 10 5.1 Marking 10 5.2 Packaging 11 6 Test report 11 Annex A (normative) Determination of thickness, length, width, squareness, straightness and flatness 12 A.1 Sampling 12 A.2 Conditioning . 12 A.3 Apparatus 12

13、A.4 Procedure 14 A.4.1 Determination of thickness (t) 14 A.4.2 Determination of length (l). 15 A.4.3 Determination of width (w) . 16 A.4.4 Determination of dimensions of squared elements 16 A.4.5 Determination of squareness (q) . 17 A.4.6 Determination of straightness (s) 17 A.4.7 Determination of w

14、idth flatness (fw) . 18 A.4.8 Determination of length flatness (fl) . 18 A.5 Calculation and expression of results . 19 A.5.1 Thickness (t) 19 A.5.2 Length (l) . 19 A.5.3 Width (w) 19 A.5.4 Squareness (q) 19 A.5.5 Straightness (s) . 20 A.5.6 Width flatness (fw) . 20 A.5.7 Length flatness (fl) . 20 A

15、nnex B (normative) Determination of openings and height difference between elements 21 B.1 Sampling 21 B.2 Conditioning . 21 B.3 Apparatus 21 B.4 Procedure 21 B.4.1 Assembling . 21 B.4.2 Determination of opening between elements (o) 22 B.4.3 Determination of height difference (h) 22 B.5 Calculation

16、and expression of results . 22 BS EN 13329:2016EN 13329:2016 (E) 3 Annex C (normative) Determination of dimensional variations after changes in relative humidity . 23 C.1 General . 23 C.2 Sampling 23 C.3 Conditioning . 23 C.4 Calculation and expression of results . 24 Annex D (normative) Determinati

17、on of surface soundness . 25 D.1 General . 25 D.2 Sampling 25 D.3 Conditioning . 25 D.4 Procedure 25 D.4.1 Preparing the test specimen . 25 D.4.2 Bonding the steel pad to the surface 26 D.4.3 Determination of force at fracture . 26 D.5 Calculation and expression of results . 26 Annex E (normative) D

18、etermination of abrasion resistance and abrasion classification 27 E.1 Sampling 27 E.2 Conditioning . 27 E.3 Apparatus 28 E.3.1 Testing machine 28 E.3.2 Additional material or equipment . 31 E.4 Procedure 31 E.4.1 General . 31 E.4.2 Preparation of test specimens and abrasive papers 31 E.4.3 Preparat

19、ion of abrasive wheels . 31 E.4.4 Determination of the abrasion rate of abrasive paper . 31 E.4.5 Abrasion of test specimen . 32 E.4.6 Expression of results . 33 E.4.7 Test report 33 Annex F (normative) Calibration and Maintenance of Abrasion equipment . 34 F.1 General . 34 F.2 Apparatus 34 F.3 Proc

20、edure 34 F.3.1 Bearing Wear 34 F.3.2 Shaft Wear . 34 F.3.3 Alignment 35 Annex G (normative) Measurement of shore A hardness . 37 Annex H (normative) Determination of impact resistance and impact classification 38 H.1 General . 38 H.2 Sampling 38 H.3 Apparatus 38 H.4 Procedure 38 H.4.1 Large-diameter

21、 ball test . 38 H.4.2 Small-diameter ball test . 39 Bibliography . 42 BS EN 13329:2016EN 13329:2016 (E) 4 European foreword This document (EN 13329:2016) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN. Th

22、is European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2016, and conflicting national standards shall be withdrawn at the latest by September 2016. Attention is drawn to the possibility that some

23、 of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13329:2006+A1:2008. Compared to EN 13329:2006+A1:2008, the following changes have been made: a) general definition for l

24、aminate floor coverings included; b) test method for the light fastness stated more precisely; c) general requirements for thickness tolerances of elements with pre-attached underlays added; d) requirements for abrasion resistance changed; e) requirements for cigarette resistance deleted; f) general

25、 requirements for surface soundness changed into a classification requirement, requirements partly increased; g) defined underlay for the impact resistance test with the large diameter ball added and requirements for this property changed; h) requirements for castor chair test changed; i) requiremen

26、ts for thickness swelling partly changed; j) requirements for locking strength added; k) requirements for dimensional stability changed; l) technical characteristic micro-scratch resistance adde; m) test method for abrasion resistance in Annex E stated more precisely; n) Annex G for hardness measure

27、ments for abrasion wheels added; o) test method for impact resistance in Annex H stated more precisely. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croati

28、a, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

29、 United Kingdom. BS EN 13329:2016EN 13329:2016 (E) 5 1 Scope This European Standard specifies characteristics, requirements and test methods for laminate floor coverings with a surface layer based on aminoplastic thermosetting resins as defined in 3.1 and 3.2. It also specifies requirements for mark

30、ing and packaging. It includes a classification system, based on EN ISO 10874, giving practical requirements for areas of use and levels of use, to indicate where laminate floor coverings will give satisfactory service and to encourage the consumer to make an informed choice. Laminate floor covering

31、s are considered for domestic and commercial levels of use, including domestic kitchens. This standard does not specify requirements relating to areas which are subjected to frequent wetting, such as bathrooms, laundry rooms or saunas. 2 Normative references The following documents, in whole or in p

32、art, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 311, Wood-based panels - Surface soundness -

33、Test method EN 318, Wood based panels - Determination of dimensional changes associated with changes in relative humidity EN 322, Wood-based panels - Determination of moisture content EN 424, Resilient floor coverings - Determination of the effect of simulated movement of a furniture leg EN 425:2002

34、, Resilient and laminate floor coverings - Castor chair test EN 438 (all parts), High-pressure decorative laminates (HPL) Sheets based on thermosetting resins (Usually called Laminates) EN 16094, Laminate floor coverings - Test method for the determination of micro-scratch resistance CEN/TS 16354, L

35、aminate floor coverings - Underlays - Specification, requirements and test methods EN 20105-A02, Textiles - Tests for colour fastness - Part A02: Grey scale for assessing change in colour (ISO 105-A02) EN ISO 105-B02, Textiles - Tests for colour fastness - Part B02: Colour fastness to artificial lig

36、ht: Xenon arc fading lamp test (ISO 105-B02) EN ISO 4892-2:2006/A1:2009, Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2006/Amd1:2009) EN ISO 6506-1, Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1) EN ISO 10874, Resilie

37、nt, textile and laminate floor coverings - Classification (ISO 10874) EN ISO 24343-1, Resilient and laminate floor coverings - Determination of indentation and residual indentation - Part 1: Residual indentation (ISO 24343-1) BS EN 13329:2016EN 13329:2016 (E) 6 ISO 48, Rubber, vulcanized or thermopl

38、astic Determination of hardness (hardness between 10 IRHD and 100 IRHD) ISO 7267-2, Rubber-covered rollers Determination of apparent hardness Part 2: Shore-type durometer method ISO 24334, Laminate floor coverings Determination of locking strength for mechanically assembled panels ISO 24336, Laminat

39、e floor coverings Determination of thickness swelling after partial immersion in water ISO 24339, Laminate and textile floor coverings Determination of dimensional variations after exposure to humid and dry climate conditions 3 Terms and definitions For the purposes of this document, the following t

40、erms and definitions apply. 3.1 laminate floor covering rigid floor covering, typically in a plank or tile format, with a multiple layer structure: e.g. backer, substrate, dcor and worked edges that allow the product to be joined together to form a larger integral unit Note 1 to entry: Laminate floo

41、ring does not include products having a resilient, stone, textile, wood, leather or metal top surfacing material(s). 3.2 surface layer based on aminoplastic thermosetting resins upper decorative layer, which may vary in surface texture and gloss level, consisting of one or more thin sheets of a fibr

42、ous material (usually paper), impregnated with aminoplastic, thermosetting resins (usually melamine) Note 1 to entry: By the simultaneous action of heat and pressure, these sheets are either pressed as such (HPL, CPL, Compact), and in the case of HPL and CPL bonded on a substrate (usually wood-based

43、 panels), or in the case of DPL directly pressed on a substrate (usually wood-based panels). The product is usually finished with a backer (e.g. HPL, CPL, impregnated papers), primarily used as a balancing material. 3.3 substrate core material of the laminate floor covering Note 1 to entry: It is ge

44、nerally a particleboard, as defined in EN 309, or a dry process fibreboard (MDF) as defined in EN 316 or a so called High Density Fibreboard (HDF) which is a MDF-board with a density 800 kg/m3. 3.4 backer layer opposite to the surface layer used to balance and stabilize the product Note 1 to entry:

45、The backer is generally made of impregnated papers. 3.5 underlay layer placed between the laminate floor covering and the subfloor to impart specific properties BS EN 13329:2016EN 13329:2016 (E) 7 Note 1 to entry: Some laminate floor covering products have the underlay pre-attached directly to the b

46、acker. 3.6 laminate floor covering element piece of the floor covering with profiled edges to facilitate assembly at installation Note 1 to entry: See Figure 1. Key 1 surface layer 2 substrate 3 backer 4 underlay (optional) Figure 1 Laminate floor-covering element 4 Requirements 4.1 General requirem

47、ents All laminate floor coverings shall conform to the general requirements given in Table 1, when tested by the methods specified therein. BS EN 13329:2016EN 13329:2016 (E) 8 Table 1 General requirements Characteristic Requirement Test method Thickness of the element, (t) without underlay taverage

48、0,50 mm, relative to nominal value tmax.- tmin. 0,50 mm Annex A With pre-attached underlay taverage 0,50 mm, relative to nominal value tmax.- tmin. 0,80 mm Annex A Length of the surface layer, (l) For the nominal values given, no measured value shall exceed: l 1 500 mm: l 0,5 mm l 1 500 mm: l 0,3 mm

49、/m Annex A Width of the surface layer, (w) waverage 0,10 mm, relative to nominal value wmax. wmin. 0,20 mm Annex A Length and width of squared elements, (l = w) laverage 0,10 mm relative to nominal value waverage 0,10 mm, relative to nominal value lmax. lmin. 0,20 mm w max. w min. 0,20 mm Annex A Squareness of the element, (q) q max. 0,20 mm Annex A Straightness of the surface layer, (s) s max. 0,30 mm/m Annex A Flatness of the element, (f) Maximum single values: f w, concave 0,15 % f w, convex 0,20 % f