EN 13063-3-2007 en Chimneys - System chimneys with clay ceramic flue liners - Part 3 Requirements and test methods for air flue system chimneys《烟囱 带粘土 陶瓷烟道衬的系统烟筒 第3部分 空气烟道系统烟囱的要求和试.pdf

《EN 13063-3-2007 en Chimneys - System chimneys with clay ceramic flue liners - Part 3 Requirements and test methods for air flue system chimneys《烟囱 带粘土 陶瓷烟道衬的系统烟筒 第3部分 空气烟道系统烟囱的要求和试.pdf》由会员分享，可在线阅读，更多相关《EN 13063-3-2007 en Chimneys - System chimneys with clay ceramic flue liners - Part 3 Requirements and test methods for air flue system chimneys《烟囱 带粘土 陶瓷烟道衬的系统烟筒 第3部分 空气烟道系统烟囱的要求和试.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 13063-3:2007Chimneys System chimneys with clay/ceramic flue liners Part 3: Requirements and test methods for air flue system chimneysThe European Standard EN 13063-3:2007 has the status of a British StandardICS 91.060.40g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g

2、54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 13063-3:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2007 BSI 2007ISBN 978 0

3、580 53347 1National forewordThis British Standard is the UK implementation of EN 13063-3:2007.The UK participation in its preparation was entrusted by Technical Committee B/506, Chimneys, to Subcommittee B/506/3, Chimneys and their components having inner linings of clay or ceramic.A list of organiz

4、ations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations

5、.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13063-3July 2007ICS 91.060.40English VersionChimneys - System chimneys with clay/ceramic flue liners - Part3: Requirements and test methods for air flue system chimneysConduits de fumes - Cond

6、uits-systmes avec conduitintrieur en terre cuite/cramique - Partie 3 : Exigences etmthodes dessai pour conduits-systmes brassage dairAbgasanlagen - System-Abgasanlagen mit Keramik-Innenrohren - Teil 3: Anforderungen und Prfungen fr Luft-AbgasleitungenThis European Standard was approved by CEN on 9 J

7、une 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtain

8、ed on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management

9、 Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Pol

10、and, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any

11、 means reservedworldwide for CEN national Members.Ref. No. EN 13063-3:2007: EEN 13063-3:2007 (E) 2 Contents Page Foreword4 1 Scope 5 2 Normative references 6 3 Terms and definitions .6 4 Shapes, dimensions and tolerances9 4.1 Air-flue system chimney .9 4.2 Terminals 9 4.3 Pressure-equalising opening

12、s .9 4.4 Air duct dimensions 9 5 Requirements.9 5.1 General9 5.2 Material requirements for air-flue system chimneys and terminals.9 5.3 Minimum compressive strength for a pressure-equalising opening section .9 5.4 Outer wall elements.10 5.5 Safety in use.10 5.5.1 Thermal resistance 10 5.5.2 Thermal

13、resistance of the flue duct (concentric) .10 5.5.3 Thermal resistance of the flue duct (side by side).10 5.5.4 Thermal resistance of the air duct .10 5.6 Resistance to fire external to external.10 5.7 Aerodynamic requirements 11 5.7.1 Flow resistance of air ducts .11 5.7.2 Aerodynamic properties of

14、terminals11 5.7.3 Pressure-equalising opening section11 6 Replacement of single components of the air flue system chimney .11 7 Designation 12 8 Product information.13 9 Marking and labelling 14 10 Evaluation of conformity.14 10.1 General14 10.2 Initial type testing 15 10.3 Evaluation of conformity

15、for the exchange of components15 10.4 Factory production control.15 Annex A (normative) Test methods .16 A.1 Compressive strength of pressure-equalising opening sections 16 A.1.1 Test sample 16 A.1.2 Testing equipment.16 A.1.3 Test procedure.16 A.2 Aerodynamic behaviour of terminals under wind condi

16、tions.16 A.2.1 Test apparatus .16 A.2.2 Test sample 16 A.2.3 Measuring parameters 16 A.2.4 Test procedure.17 A.2.5 Test results.17 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive18 ZA.1 Scope and relevant characteristics .1

17、8 EN 13063-3:2007 (E) 3 ZA.2 Procedure(s) for attestation of conformity of systems chimneys with clay/ceramic flue liners .21 ZA.2.1 System(s) of attestation of conformity21 ZA.2.2 EC Certificate and Declaration of conformity.22 ZA.3 CE marking and labelling23 Bibliography27 EN 13063-3:2007 (E) 4 Fo

18、reword This document (EN 13063-3:2007) has been prepared by Technical Committee CEN/TC 166 “Chimneys”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Janu

19、ary 2008, and conflicting national standards shall be withdrawn at the latest by April 2009. This standard is part 3 of a series of standards for system chimneys with clay/ceramic flue liners. Part 1 is for soot fire resistant system chimneys and part 2 is for system chimneys working under wet condi

20、tions. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 89/106. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this docum

21、ent. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, It

22、aly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 13063-3:2007 (E) 5 1 Scope This product standard specifies the requirements and test methods for dry (designated D) and/or wet (designated

23、W) air flue system chimneys, including terminals in which the products of combustion are conveyed to the atmosphere through clay/ceramic flue liners and combustion air is conveyed to suitable room-sealed appliances through an air duct or an air gap. It also specifies the requirements for marking, ma

24、nufacturers instructions, product information and evaluation of conformity. This standard does not apply to structurally independent (free standing or self supporting) system chimneys. An air flue system chimney is made of the following components where appropriate: clay/ceramic flue liners; insulat

25、ion layer; outer walls; mortar for jointing flue liners; acid resistant mortar or elastomeric sealant for jointing flue liners; mortar for jointing outer walls; terminal; chimney base; pressure equalising opening; air duct; air gap; cladding; opening section; cleaning and inspection door; distance p

26、iece; reinforcement. The air flue system chimney covers a combination of compatible chimney components obtained or specified from one manufacturing source, with product responsibility for the whole chimney. EN 13063-3:2007 (E) 6 2 Normative references The following referenced documents are indispens

27、able for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies EN 1443:2003, Chimneys General requirements EN 1457:1999, Chimneys Clay/Ceramic Flue Liners Requir

28、ements and test methods EN 12446, Chimneys Components Concrete outer wall elements EN 13063-1:2005, Chimneys System chimneys with clay/ceramic flue liners Part 1: Requirements and test methods for sootfire resistance EN 13063-2: 2005, Chimneys System chimneys with clay/ceramic flue liners Part 2: Re

29、quirements and test methods under wet conditions EN 13069, Chimneys Clay/ceramic outer walls for system chimneys Requirements and test methods EN 13162, Thermal insulation products for buildings Factory made mineral wool (MW) products Specification EN 13216-1:2004, Chimneys Test methods for system c

30、himneys Part 1: General test methods. EN 13384-1, Chimneys Thermal and fluid dynamic calculation methods Part 1: Chimneys serving one appliance ISO 2859-1, Sampling procedures for inspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection 3

31、Terms and definitions For the purposes of this document, the terms and definitions given in EN 1443:2003, EN 13063-1:2005, EN 13063-2:2005 and the following apply. 3.1 air flue system chimney chimney with an air duct (combustion air), flue duct (flue gas) and terminal for room-sealed appliances 3.2

32、concentric air flue system chimney chimney with the air duct concentric around the flue EN 13063-3:2007 (E) 7 Key 1 Flue duct 2 Insulation layer 3 Outer wall 4 Cavities for structural reinforcement 5 Air gap Figure 1 Examples of cross sections of concentric air flue system chimneys EN 13063-3:2007 (

33、E) 8 3.3 side-by-side air flue system chimney chimney with the air duct side-by-side to the flue Key 1 Flue duct 2 Insulation layer or air gap 3 Outer wall 4 Cavities for structural reinforcement 5 Air duct 6 Back ventilation Figure 2 Examples of cross sections of side-by-side air flue system chimne

34、ys 3.4 terminal element consisting of an air inlet and a flue outlet which is situated at the top of the air fluesystem chimney 3.5 pressure-equalising opening opening that directly connects the air duct/air gap with the flue which is situated at the base of the air fluesystem chimney 3.6 air duct/a

35、ir gap part of the air fluesystem chimney which conveyscombustion air to room-sealed appliances 3.7 recirculation percentage ratio between the amount of flue gases leaking through the flue opening into the air duct opening of the terminal and the total amount of flue gases produced 3.8 wind pressure

36、 angle angle related to horizontal at which the wind impinges upon the air/flue terminal EN 13063-3:2007 (E) 9 3.9 wind effect pressure additional pressure difference between the inlet and the outlet of the terminal due to wind 4 Shapes, dimensions and tolerances 4.1 Air-flue system chimney The requ

37、irements for shapes, dimensions and tolerances shall be as given in EN 13063-1:2005, clause 4. 4.2 Terminals When terminals are supplied with the air-flue system chimneys, the dimensions and tolerances of the terminals shall be declared by the manufacturer. 4.3 Pressure-equalising openings Where pre

38、ssure-equalising openings are supplied with the air-flue system chimneys, dimensions and tolerances of the pressure-equalising openings shall be declared by the manufacturer. 4.4 Air duct dimensions Dimensions and tolerances shall be declared by the manufacturer. 5 Requirements 5.1 General The mater

39、ial requirements of this standard are covered by the requirements given in EN 13063-1 and EN 13063-2. 5.2 Material requirements for air-flue system chimneys and terminals All air flue system chimneys designated D, excluding terminals, shall be in accordance with the material requirements of EN 13063

40、-1:2005, clause 5. Concentric air flue system chimneys designated W, excluding terminals, shall be in accordance with the material requirements of EN 13063-2:2005, clause 5. In addition the flue liner shall have a water vapour resistance less than or equal to 10 (g/h m2) measured according to EN 145

41、7:1999, 16.13. Side-by-side air flue system chimneys designated W shall be in accordance with the material requirements of EN 13063-2:2005, clause 5. Material requirements for terminals shall be specified according to the appropriate European standard or, in the absence of European standards, accord

42、ing to the manufacturers specification. 5.3 Minimum compressive strength for a pressure-equalising opening section The minimum compressive strength for a pressure-equalising opening section shall be in accordance with the requirements for opening sections of EN 13063-1:2005, 5.1.3 when testing in ac

43、cordance with Annex A. NOTE The limiting factor of the maximum height of system chimneys is the compressive strength of the opening section or pressure-equalising opening section (inner liner or outer wall). EN 13063-3:2007 (E) 10 5.4 Outer wall elements The outer wall elements shall fulfil EN 12446

44、 for concrete outer wall elements, or EN 13069 for clay/ceramic outer wall elements, or EN 13063-1:2005, Annex B for stainless steel metal outer walls. 5.5 Safety in use 5.5.1 Thermal resistance For air flue system chimneys the thermal resistance of the flue duct and the thermal resistance of the ai

45、r duct shall be declared by the manufacturer. 5.5.2 Thermal resistance of the flue duct (concentric) The thermal resistance value of the flue duct (inner liner with or without insulation) shall be declared by the manufacturer and shall be verified by testing according to the test method of EN 13216-

46、1:2004, clause 5.8 (reference test method) or calculation in accordance with EN 13063-1:2005, Annex C, both with inner surface temperature of the flue liner at 200C. 5.5.3 Thermal resistance of the flue duct (side by side) The thermal resistance value of the flue duct (inner liner with or without in

47、sulation and outer wall) shall be declared by the manufacturer and shall be verified by testing according to the test method of EN 13216-1:2004 clause 5.8 (reference test method) or calculating in accordance with EN 13063-1:2005, Annex C, both with an inner flue liner surface temperature of 200 C. 5

48、.5.4 Thermal resistance of the air duct The thermal resistance value of the air duct declared by the manufacturer shall be verified by testing according to the test method of EN 13216-1 (reference test method) or calculation in accordance with EN 13063-1:2005, Annex C, related to 20 C. NOTE In the a

49、bsence of a European test method, the outer surface temperature of the air duct/air gap should not be less than the dew point temperature of the ambient air if calculated or measured according to national methods and boundary values. 5.6 Resistance to fire external to external Until a European test method is available,resistance to fire, external to external, shall be evaluated and declared according to national regulations. Examples of European classification are given in Table 1. Table 1