EN 13024-2-2004 en Glass in building - Thermally toughened borosilicate safety glass - Part 2 Evaluation of conformity Product standard《建筑用玻璃 热钢化硼硅酸盐安全玻璃 第2部分 合格评价 产品标准》.pdf

《EN 13024-2-2004 en Glass in building - Thermally toughened borosilicate safety glass - Part 2 Evaluation of conformity Product standard《建筑用玻璃 热钢化硼硅酸盐安全玻璃 第2部分 合格评价 产品标准》.pdf》由会员分享，可在线阅读，更多相关《EN 13024-2-2004 en Glass in building - Thermally toughened borosilicate safety glass - Part 2 Evaluation of conformity Product standard《建筑用玻璃 热钢化硼硅酸盐安全玻璃 第2部分 合格评价 产品标准》.pdf（40页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 13024-2:2004 Glass in building Thermally toughened borosilicate safety glass Part 2: Evaluation of conformity/Product standard The European Standard EN 13024-2:2004 has the status of a British Standard ICS 81.040.20 BS EN 13024-2:2004 This British Standard was published under

2、the authority of the Standards Policy and Strategy Committee on 20 October 2004 BSI 20 October 2004 ISBN 0 580 44631 X National foreword This British Standard is the official English language version of EN 13024-2:2004. The UK participation in its preparation was entrusted by Technical Committee B/5

3、20, Glass and glazing in building, to Subcommittee B/520/1, Glass and glazing in building Basic and transformed glass products, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standard

4、s which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This pu

5、blication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible internat

6、ional/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN titl

7、e page, pages 2 to 36, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN130242 October2004 ICS81.040.20 En

8、glishversion GlassinbuildingThermallytoughenedborosilicatesafetyglass Part2:Evaluationofconformity/Productstandard VerredanslaconstructionVerreborosilicatdescurit trempthermiquementPartie2:Evaluationdela conformit GlasimBauwesenThermischvorgespanntesBorosilicat EinscheibensicherheitsglasTeil2: Konfo

9、rmittsbewertung/Produktnorm ThisEuropeanStandardwasapprovedbyCENon27May2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings

10、uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesa

11、mestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,Switzerlan

12、dandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN130242:2004:EEN 13024-2:2004 (E) 2 Cont

13、ents Page Foreword. 4 1 Scope 5 2 Normative references . 5 3 Definitions 6 4 Requirements 6 4.1 Product description 6 4.2 Conformity with the definition of thermally toughened borosilicate safety glass. 7 4.3 Determination of the characteristics performances. 7 4.3.1 Characteristics of thermally tou

14、ghened borosilicate safety glass 7 4.3.2 Determination of characteristics of thermally toughened borosilicate safety glass products. 8 4.4 Durability 10 4.5 Dangerous substances. 11 5 Evaluation of conformity 11 5.1 General. 11 5.2 Initial type testing of the product (see 5.1, 2). 11 5.2.1 General.

15、11 5.2.2 Initial type testing of thermally toughened borosilicate safety glass . 13 5.2.3 Initial type testing of characteristics performances. 15 5.3 Factory production control and inspection of samples in accordance with a prescribed test plan (see 5.1, 1a and b) 16 5.4 Initial inspection of facto

16、ry and of factory production control (see 5.1, 1c). 16 5.5 Continuous surveillance and assessment of the factory production control (see 5.1, 1c) 17 6 Marking and/or labelling. 18 6.1 General. 18 6.2 Product marking 18 6.3 Product characteristics 18 6.4 “Characteristics/performance identification pa

17、per” . 18 Annex A (normative) Factory production control 19 A.1 Factory Production Control Requirements 19 A.1.1 General. 19 A.1.2 Organisation 19 A.1.3 Control system 19 A.2 Marking 20 A.3 Inspection and testing tables of thermally toughened borosilicate safety glass production . 20 A.3.1 Informati

18、on on Table A.1 20 A.3.2 Use of proxy testing 21 Annex B (informative) Tests for factory production control 25 B.1 Strength measurement. 25 B.1.1 Four point bending strength test 25 B.1.2 Optical surface pre-stress measurement . 25 B.2 Fragmentation test 26 B.2.1 Requirements 26 B.2.2 Test method. 2

19、6 Annex C (informative) Provisions for voluntary involvement of third party(ies) . 27 EN 13024-2:2004 (E) 3 C.1 General. 27 C.2 Voluntary tasks for third parties 27 C.3 Marking and labelling . 27 Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU Construction Pr

20、oducts Directive. 28 ZA.1 Scope and relevant characteristics. 28 ZA.2 Procedure(s) for the attestation of conformity of thermally toughened borosilicate safety glass products . 30 ZA.2.1 System(s) of attestation of conformity . 30 ZA.2.2 EC Certificate and Declaration of conformity 32 ZA.3 CE markin

21、g and labelling . 34 Bibliography . 36 EN 13024-2:2004 (E) 4 Foreword This document (EN 13024-2:2004) has been prepared by Technical Committee CEN/TC TC 129 “Glass in building”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either b

22、y publication of an identical text or by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by July 2006. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and su

23、pports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, B, C or D, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to im

24、plement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingd

25、om. No existing document is superseded This part of the document does not stand-alone; it is a part of one document: EN 13024-1: Glass in Building Thermally toughened borosilicate safety glass Part 1: Definition and description EN 13024-2: Glass in Building - Thermally toughened borosilicate safety

26、glass Part 2: Evaluation of conformity/Product standard This document has been prepared under a mandate given to CEN by the Commission of the European Commission and the European Free Trade Association, and supports the essential requirements of EC Directive(s). This document contains other aspects

27、of importance of trade. EN 13024-2:2004 (E) 5 1 Scope This document covers the evaluation of conformity and the factory production control of flat thermally toughened borosilicate safety glass for use in buildings. Note: For glass products with electrical wiring or connections for, e.g. alarm or hea

28、ting purposes, other directives, e.g. Low Voltage Directive, may apply. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced

29、 document (including any amendments) applies. EN 356, Glass in building - Security glazing - Testing and classification of resistance against manual attack EN 410, Glass in building - Determination of luminous and solar characteristics of glazing EN 673, Glass in Building Determination of thermal tr

30、ansmittance (U value) Calculation method EN 1063, Glass in building - Security glazing - Testing and classification of resistance against bullet attack EN 1096-1, Glass in building - Coated glass - Part 1: Definitions and classification EN 1096-2, Glass in building - Coated glass - Part 2: Requireme

31、nts and test methods for class A, B and S coatings EN 1096-3, Glass in building - Coated glass - Part 3: Requirements and test methods for class C and D coatings EN 1748-1-1, Glass in building - Special basic products -Borosilicate glasses - Part 1-1: Definition and general physical and mechanical p

32、roperties EN 12600, Glass in building - Pendulum test - Impact test method and classification for flat glass EN 12758, Glass in building - Glazing and airborne sound insulation Product descriptions and determination of properties EN 12898, Glass in building - Determination of the emissivity EN 13024

33、-1:2002, Glass in building Thermally toughened borosilicate safety glass Part 1: Definition and description prEN 13474, Glass in building - Design of glass panes EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using test data from reaction to fir

34、e tests EN 13501-2, Fire classification of construction products and building elements Part 2: Classification using data from fire resistance tests, excluding ventilation services EN 13024-2:2004 (E) 6 prEN 13501-5, Fire classification of construction products and building elements - Part 5: Classif

35、ication using test data from external fire exposure to roof tests EN 13541, Glass in building - Security glazing - Testing and classification of resistance against explosion pressure 3 Definitions For the purposes of this document, the terms and definitions given in EN 13024-1:2002 and the following

36、 apply. 3.1 initial type testing determination of the performance of a product (characteristic, durability), on the basis of either actual tests or other procedures (such as conventional, standardised, tabulated or general accepted values, standardised or recognised calculation methods, test reports

37、 when made available, ), in accordance with this standard that demonstrates compliance with this standard 3.2 test report document that covers the results of tests undertaken on a representative sample of the product from production or on a prototype design of the product 3.3 product description doc

38、ument that details the relevant parameters, e.g. process conditions, structure, etc., for defining a product that complies with the standard. It includes specific reference(s) to characteristics that are modified by the production process 3.4 significant change variation in performance beyond the pe

39、rmitted tolerance for the characteristic 4 Requirements 4.1 Product description For conformity purposes the thermally toughened glass manufacturer is responsible for the preparation and maintenance of the product description. This description shall describe the product and/or product families. Discl

40、osure of the product description shall be at the discretion of the thermally toughened glass manufacturer or his agent except in the case of regulatory requirements. The description shall contain at least a normative part. The description may also contain an informative part, when the manufacturer f

41、oresees further development of the product. The normative part of the description shall contain the following minimum information: - a reference to EN 13024 parts 1 and 2 and all other standards with which the manufacturer claims compliance. - the radiometric properties and durability of coated glas

42、s, i.e. coated glass that conforms with EN 1096-1, EN 1096-2, EN 1096-3, when those properties are changed, intentionally or unintentionally, by the thermal toughening process. EN 13024-2:2004 (E) 7 The definition of product families shall be consistent with the normative part of the product descrip

43、tion. The substitution of materials shall maintain the conformity with the product description. The substituting material can be added to the product family and also the product description when compliance has been demonstrated. 4.2 Conformity with the definition of thermally toughened borosilicate

44、safety glass Products shall conform to the definition and fulfil the requirements of thermally toughened borosilicate safety glass as defined in EN 13024-1. 4.3 Determination of the characteristics performances 4.3.1 Characteristics of thermally toughened borosilicate safety glass 4.3.1.1 General Th

45、e characteristics of thermally toughened borosilicate safety glass are in general those of the glass substrate ( see 4.3.1.2). 4.3.1.2 Characteristics of the borosilicate glass panes used for the production of thermally toughened borosilicate safety glass Panes shall be made of borosilicate glass ac

46、cording to EN 1748-1-1. The panes may be coated according to EN 1096 1, EN 1096-2, EN 1096-3 and/or enamelled according to EN 13024-1. For the characteristics listed in Table 1, for the borosilicate glass panes, generally accepted values or calculated values may be used. Since the majority of the ch

47、aracteristics of Table 1 are not changed significantly by the thermal toughening process they shall be used for thermally toughened borosilicate safety glass. The exceptions shall be the characteristic bending strength (f g,k ) and the resistance against sudden temperature changes and temperature di

48、fferentials. EN 13024-2:2004 (E) 8 Table 1: Information on the characteristics of borosilicate glass panes, according to EN 1748- 1-1, used for the production of thermally toughened borosilicate safety glass Characteristic Symbol Unit - density - hardness - Youngs modulus - Poissons ratio - Characteristic bending strength - Resistance against sudden temperature changes and temperature differentials - Specific heat capacity - Coefficient of linear expansion - Thermal conductivity (for U-value) - Mean refractive index to visible