EN 12288-2010 en Industrial valves - Copper alloy gate valves《工业阀门 铜合金闸阀》.pdf

《EN 12288-2010 en Industrial valves - Copper alloy gate valves《工业阀门 铜合金闸阀》.pdf》由会员分享，可在线阅读，更多相关《EN 12288-2010 en Industrial valves - Copper alloy gate valves《工业阀门 铜合金闸阀》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 12288:2010Industrial valves Copperalloy gate valvesBS EN 12288:2010 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 12288:2010. Itsupe

2、rsedes BS EN 12288:2003 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PSE/18/2, Industrial valves, steam traps, actuators andsafety devices against excessive pressure - Gate, globe, diaphragmand check valves.A list of organizations represented on this

3、 committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 68321 3ICS 23.060.30Compliance with a British Standard cannot confer immunity fromleg

4、al obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2010Amendments issued since publicationDate Text affectedBS EN 12288:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12288 May 2010 ICS 23.060.30 Supersedes EN 122

5、88:2003English Version Industrial valves - Copper alloy gate valves Robinetterie industrielle - Robinets-vannes en alliage de cuivre Industriearmaturen - Schieber aus Kupferlegierungen This European Standard was approved by CEN on 16 April 2010. CEN members are bound to comply with the CEN/CENELEC I

6、nternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN

7、member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN m

8、embers are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spa

9、in, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national M

10、embers. Ref. No. EN 12288:2010: EBS EN 12288:2010EN 12288:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .54 Requirements .64.1 Classification 64.1.1 Nominal sizes .64.1.2 Nominal size relationships .74.1.3 PN and Class designations .84.1.4 Valve series 9

11、4.2 Design .94.2.1 General 94.2.2 Materials .94.2.3 Pressure/temperature ratings .94.2.4 Dimensions .94.2.5 Operation . 114.2.6 Auxiliary connections 124.3 Functional characteristics . 124.3.1 Shell design strength . 124.3.2 Obturator design strength . 124.3.3 Shell tightness 124.3.4 Seat tightness

12、. 124.3.5 Flow characteristics . 134.3.6 Sizing the operating element . 145 Test procedures 145.1 Production pressure testing 145.2 Applicability of gas tests . 155.3 Test durations . 156 Declaration of compliance . 157 Designation . 158 Marking and preparation for storage and transportation . 168.1

13、 Required markings . 168.1.1 Mandatory markings . 168.1.2 Supplementary markings . 168.1.3 Other markings . 168.1.4 Omission of markings 178.2 Preparation for storage and transportation . 178.2.1 Protection 178.2.2 Obturator position 178.2.3 Body ends 17Annex A (normative) Materials . 18Annex B (nor

14、mative) Pressure/temperature ratings . 20B.1 Valves with metallic body seats and obturator seats . 20B.2 Valves with non-metallic obturator seats and/or body seats . 21Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC . 22Bibli

15、ography . 23BS EN 12288:2010EN 12288:2010 (E) 3 Foreword This document (EN 12288:2010) has been prepared by Technical Committee CEN/TC 69 “Industrial valves”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of

16、an identical text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn at the latest by November 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall no

17、t be held responsible for identifying any or all such patent rights. This document supersedes EN 12288:2003 This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 97/23/EC. F

18、or relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. This document supersedes EN 12288:2003 where the following modifications were made: a) the normative references were updated in Clauses 2 and 3, in 4.1.1, in 4.1.4, in Table 5, in 4.2.4.3, in Tab

19、les A.1 and A.2, in Table B.1; b) Table 5 and Table B.1 were corrected; c) in Table ZA.1: 1) sub-clause 4.2 was correlated to PED Annex I, section 2.1; 2) sub-clause 4.2.3 was correlated to PED Annex I, section 2.2; 3) correlation of sub-clause 4.2.3 to PED Annex I, section 2.2.1 was deleted; 4) cor

20、relation of sub-clause 4.2.6 to PED Annex I, section 2.5 was deleted; 5) correlation of Annex A to PED Annex I, section 4.2 was deleted. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: A

21、ustria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdo

22、m. BS EN 12288:2010EN 12288:2010 (E) 4 1 Scope This European Standard applies to copper alloy gate valves for general use having flanged, threaded, capillary, compression or loose nut/union body ends. This European Standard specifies the design and performance requirements including materials, press

23、ure/temperature ratings, dimensions, test procedures and marking. For some specific fields of application, for example, drinking water or gas, valves to this European Standard can be used provided the requirements of the relevant performance standards are met. Approval by the relevant regulatory bod

24、y may be required. The range of nominal sizes is DN 8 to DN 500 and of nominal diameters is 8 mm to 110 mm. The range of pressure designations covered is PN 6; PN 10; PN 16; PN 20; PN 25; PN 32; PN 40; PN 63; Class 150 and Class 300. For the applicability of each nominal size/diameter and each press

25、ure designation to the different types of valve end, see 4.1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document

26、(including any amendments) applies. EN 19:2002, Industrial valves Marking of metallic valves EN 558:2008, Industrial valves Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems PN and Class designated valves EN 736-1, Valves Terminology Part 1: Definition of typ

27、es of valves EN 736-2, Valves Terminology Part 2: Definition of components of valves EN 736-3, Valves Terminology Part 3: Definition of terms EN 1057, Copper and copper alloys Seamless round copper tubes for water and gas in sanitary and heating applications EN 1092-3:2003, Flanges and their joints

28、Circular flanges for pipes, valves, fittings and accessories, PN designated Part 3: Copper alloy flanges EN 1759-3:2003, Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, Class designated Part 3: Copper alloy flanges EN 1982:2008, Copper and copper alloys Ingots

29、and castings EN 12163:1998, Copper and copper alloys Rod for general purposes EN 12164:1998, Copper and copper alloys Rod for free machining purposes EN 12167:1998, Copper and copper alloys Profiles and rectangular bar for general purposes EN 12168:1998, Copper and copper alloys Hollow rod for free

30、machining purposes BS EN 12288:2010EN 12288:2010 (E) 5 EN 12266-1:2003, Industrial valves Testing of valves Part 1: Pressure tests, test procedures and acceptance criteria Mandatory requirements EN 12266-2:2002, Industrial valves Testing of valves Part 2: Tests, test procedures and acceptance criter

31、ia Supplementary requirements EN 12420:1999, Copper and copper alloys Forgings“ EN 12449, Copper and copper alloys Seamless, round tubes for general purposes EN 12516-3, Valves Shell design strength Part 3: Experimental method EN 12570, Industrial valves Method for sizing the operating element EN IS

32、O 228-1:2003, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) EN ISO 5210:1991, Industrial valves Multi-turn valve actuator attachments (ISO 5210:1991) ISO 7-1:1994, Pipe threads where pressure-tight joints are made

33、 on the threads Part 1: Dimensions, tolerances and designation ASME B1.20.1:1983, Pipe threads, general purpose (inch) 3 Terms and definitions For the purposes of this document, the terms and definitions of types of valves and components and the terms and definitions given in EN 736-1, EN 736-2 and

34、EN 736-3 apply, together with the following terms and definitions. NOTE The terms maximum allowable pressure, PS, and test pressure, PT, defined in EU Directive 97/23/EC (PED) are equivalent to the terms allowable pressure, ps, and test pressure, pt, defined in EN 736-3:2008. 3.1 loose nut end body

35、end provided with a tailpiece which retains a loose internally threaded nut or ring for connection to the mating component 3.2 union end body end provided with an external thread to which is attached a threaded nut or ring, which retains a tailpiece for connection to the mating component 3.3 NPS alp

36、hanumeric designation of size for components of a pipework system, which is used for reference purposes and which comprises, for the purpose of Class designated flanges according to this standard, the letters NPS followed by a dimensionless number which is indirectly related to the physical size of

37、the bore or outside diameter of the end connections NOTE The number following the letters NPS does not represent a measurable value and should not be used for calculation purposes except where specified in the relevant standard. See EN ISO 6708. Adapted from EN 1759-3:2003 BS EN 12288:2010EN 12288:2

38、010 (E) 6 4 Requirements 4.1 Classification 4.1.1 Nominal sizes The nominal sizes applicable to each type of body end shall be as specified in Tables 1 and 2. NOTE 1 DN is applicable to flanged valves (PN designated) and loose nut/union end valves and NPS is applicable to flanged valves (Class desig

39、nated). Threaded valves are normally identified by the thread size (NPS). Capillary and compression end valves are normally identified by nominal diameter expressed as the nominal outside diameter of the connecting tube or pipe. The use of DN for valves with body ends other than flanged is permitted

40、. NOTE 2 DN 8 is not listed in EN ISO 6708:1995 but is the commonly used equivalent nominal size for valves having size threaded ends. NOTE 3 NPS and NPS are not listed in EN 1759-3:2003. Table 1 Nominal sizes for flanged, threaded and loose nut/union end valves Nominal size Valve body ends Nominal

41、size Valve body ends Flanged Threaded Loose nut, union end Flanged Threaded PN Class PN Class DN 8 - - - DN 100 DN 100 4 4 DN 10 DN 10 - DN 10 DN 125 DN 125 5 - DN 15 DN 15 DN 15 DN 150 DN 150 6 - DN 20 DN 20 DN 20 DN 200 DN 200 8 - DN 25 DN 25 1 1 DN 25 DN 250 DN 250 10 - DN 32 DN 32 1 1 DN 32 DN 3

42、00 DN 300 12 - DN 40 DN 40 1 1 DN 40 DN 350 DN 350 14 - DN 50 DN 50 2 2 DN 50 DN 400 DN 400 16 - DN 65 DN 65 2 2 - DN 450 DN 450 18 - DN 80 DN 80 3 3 - DN 500 DN 500 20 - BS EN 12288:2010EN 12288:2010 (E) 7 Table 2 Nominal diameters for capillary and compression end valves Nominal diameter mm Valve

43、body ends Nominal diameter mm Valve body ends Capillary and compression ends for copper tubes Compression ends for plastic pipe Capillary and compression ends for copper tubes Compression ends for plastic pipe 8 O - 40 X O 10 O O 40,5 X X12 O O 42 O - 14 X X 50 - O 14,7 X X 53,6 X X 15 O X 54 O - 16

44、 X O 63 - O18 O X 64 O - 20 - O 66,7 O -21 X X 70 X - 22 O X 75 - O 25 X O 76,1 O -27,4 X X 80 X - 28 O X 88,9 O - 32 - O 90 - O34 X X 108 O - 35 O - 110 - ONOTE O = recommended European tube or pipe outside diameters. X = other European tube or pipe outside diameters. 4.1.2 Nominal size relationshi

45、ps The relationship between nominal size, DN, and body end types shall be as given in Table 3. BS EN 12288:2010EN 12288:2010 (E) 8 Table 3 Relationship between nominal size, DN, and body end types Nominal size DN Body end types Flanged Threaded Loose nut, union end Capillary and compression ends for

46、 copper tubes Compression ends for plastic pipe PN Class Nominal size Nominal diameter DN NPS NPS DN DN 8 8 - - 8 ; 10 10 DN 10 10 - 10 12 ; 14 12 ; 14 DN 15 15 15 14,7 ; 15 ; 16 ; 18 14,7 ; 15 ;16 ;18 DN 20 20 20 21 ; 22 20 ; 21 ; 22 DN 25 25 1 1 25 25 ; 27,4 ; 28 25 ; 27,4 ; 28 DN 32 32 1 1 32 34

47、; 35 32 ; 34 DN 40 40 1 1 40 40 ; 40,5 ; 42 40 ; 40,5 DN 50 50 2 2 50 53,6 ; 54 50 ; 53,6 DN 65 65 2 2 - 64 ; 66,7 ; 70 ; 76,1 63 ; 75 DN 80 80 3 3 - 80 ; 88,9 90 DN 100 100 4 4 - 108 110 DN 125 125 5 - - - - DN 150 150 6 - - - - DN 200 200 8 - - - - DN 250 250 10 - - - - DN 300 300 12 - - - - DN 35

48、0 350 14 - - - - DN 400 400 16 - - - - DN 450 450 18 - - - - DN 500 500 20 - - - - 4.1.3 PN and Class designations The PN and Class designations applicable to valves having flanged, threaded and loose nut/union end body ends shall be as specified in Table 4. NOTE 1 PN 20 and PN 32 are established PN

49、 designations for threaded end copper alloy valves and are additional to the list of PN designations given in EN 1333:2006. Valves with capillary or compression ends are not designated by PN or Class. NOTE 2 EN 1254-1:1998, EN 1254-2:1998, EN 1254-3:1998 and EN 1254-5:2007 which give details ofthe body ends for capillary and compression end valves in this European Standard, do