EN 12274-1-2018 en Slurry surfacing - Test methods - Part 1 Sampling of slurry surfacing mixture.pdf

《EN 12274-1-2018 en Slurry surfacing - Test methods - Part 1 Sampling of slurry surfacing mixture.pdf》由会员分享，可在线阅读，更多相关《EN 12274-1-2018 en Slurry surfacing - Test methods - Part 1 Sampling of slurry surfacing mixture.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Slurry surfacing Test methodsPart 1: Sampling of slurry surfacing mixtureBS EN 122741:2018National forewordThis British Standard is the UK implementation of EN 122741:2018. It supersedes BS EN 122741:2002, which is with

2、drawn.The UK participation in its preparation was entrusted to Technical Committee B/510/2, Surface treatments.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Us

3、ers are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 92275 6ICS 93.080.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority o

4、f the Standards Policy and Strategy Committee on 31 March 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 122741:2018EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 122741March 2018ICS 93.080.20 Supersedes EN 122741:2002EUROPEAN COMMITTEE FOR STANDARDIZAT

5、IONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCENCENELEC Management Centre: Avenue Marnix 17, B1000 Brussels 2018 CEN Ref. No. EN 122741:2018: EAll rights of exploitation in any form and by any means reserved worldwide for CEN national MembersSlurry surfacing Test methods Part 1: Sa

6、mpling of slurry surfacing mixtureMatriaux bitumineux couls froid Mthode dessai Partie 1: Echantillonnage de Matriaux Bitumineux Couls FroidDnne Asphaltdeckschichten in Kaltbauweise Prfverfahren Teil 1: ProbenahmeThis European Standard was approved by CEN on 13 November 2017.CEN members are bound to

7、 comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Uptodate lists and bibliographical references concerning such national standards may be obtained on application to the CENCENEL

8、EC Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the s

9、ame status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg

10、, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN 122741:2018 (E)European foreword 31 Scope . 42 Apparatus for sampling . 42.1 Suitable containers with a capacity of minimum 0,5 l 42.2 Stirring

11、 rod with a diameter of 20 mm to 30 mm and of suitable length 43 Procedure for sampling . 44 Sample labelling 4Annex A (informative) Procedure for sampling after laying 62Contents PageBS EN 122741:2018EN 122741:2018 (E)European forewordThis document (EN 12274-1:2018) has been prepared by Technical C

12、ommittee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2018, and conflicting national standards shall be withdrawn

13、at the latest by September 2018.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.This document supersedes EN 12274 1:2003.Compared with EN 12274 1:2003

14、, the following changes have been made:a) the position of when to take a sample from production has been defined;b) an informative annex has been added to evaluate sampling after laying.This European Standard is one of a series of standards as listed below: EN 12274-1, Slurry surfacing Test methods

15、Part 1: Sampling of slurry surfacing mixture EN 12274-2, Slurry surfacing Test methods Part 2: Determination of residual binder content including preparation of samples EN 12274-3, Slurry surfacing Test methods Part 3: Consistency EN 12274-4, Slurry surfacing Test methods Part 4: Determination of co

16、hesion of the mix EN 12274-5, Slurry surfacing Test methods Part 5: Determination of the minimum binder content and wearing resistance EN 12274-6, Slurry surfacing Test methods Part 6: Rate of application EN 12274-7, Slurry surfacing Test methods Part 7: Shaking abrasion test EN 12274-8, Slurry surf

17、acing Test methods Part 8: Visual assessment of defectsAccording to the CENCENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finla

18、nd, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.3BS EN 122741:2018EN 12274

19、1:2018 (E)1 ScopeThis European Standard applies to slurry surfacing for roads, airfields and other trafficked areas.This European Standard specifies a method for sampling of slurry surfacing mixtures from production during laying.A method for sampling from the road surface after laying is described

20、in an informative annex (Annex A) for evaluation purposes.Production testing needs operators with good practice and is carried out provided there are no specific local or other national regulations that are required to be followed.WARNING The use of this standard may involve hazardous materials, ope

21、rations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of the standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.2 Appa

22、ratus for sampling2.1 Suitable containers with a capacity of minimum 0,5 lIn order to achieve the amount of sample needed, several containers may be used. For closing the containers a tightly fitting lid is recommended.A sampling frame to hold one or more containers may be used.2.2 Stirring rod with

23、 a diameter of 20 mm to 30 mm and of suitable lengthIn order to achieve a homogeneous sample, stirring might be required.3 Procedure for sampling1) All samples of the slurry surfacing mixture shall be taken during production, immediately before being laid. No sample shall be taken until the laid mat

24、erial appears uniform and homogeneous. No sample shall be taken at the very beginning or end of production. The sample has to be taken until the machine has laid on road at least 30 linear metres of material.NOTE 1 For small machines used on footways and cycle ways the sample can be taken at any tim

25、e during production before being laid, this can also be from a batch mix.2) Take the sample by holding the container(s) in the full flow of the discharging mixture until it is (each are) full but not overflowing. NOTE 2 A sample frame is a convenient and safe method to hold the containers.3) Samples

26、 of slurry surfacing mixture shall be packed and stored so that no contamination or damage to the sample takes place.4) If the sample is large or has to be divided for testing then it may be necessary to stir the sample continuously until the slurry surfacing mixture has achieved an initial set to e

27、nsure all the aggregate particles remain in suspension and do not segregate.4 Sample labellingThe sampling report shall contain the minimum information:a) name of the Producer (Contractor);4 BS EN 122741:2018EN 122741:2018 (E)b) type of slurry surfacing (e.g. base layer or surface layer of microsurf

28、acing; aggregate origin and grading; modified or unmodified slurry surfacing; fibre type; etc.);c) date of sampling;d) identification of the slurry surfacing machine;e) designation of samples ;f) location of sampling and site name;g) possible additional information:h) name of the sampling organizati

29、on;i) reference to this European Standard;j) any deviations from the procedure described in the standard.Optional information:k) weather conditions;l) emulsion origin;m) time of sampling.5BS EN 122741:2018EN 122741:2018 (E)Annex A (informative) Procedure for sampling after layingA.1 General1) Self-a

30、dhesive masking tape covering a minimum area of 0,1 m2 shall be fixed on the surface to obtain a representative sample.2) The position of the tape shall be recorded and for roads shall be at least 30 m from the start of production to ensure a homogeneous mixture.NOTE 1 Samples can be conveniently ob

31、tained from appropriately positioned masked ironwork e.g. utility covers.3) The tape shall be similar to that used for the protection of ironworks during road resurfacing, and therefore capable of adhering to steel at ambient road temperatures. Minimum thickness of 0,2 mm and minimum breaking load o

32、f 5,8 103kN/mm.4) After laying and the slurry surfacing has set, the sample is removed together with the masking tape from the surface.5) The total mass of the sample and masking tape and area of the sample may be optionally recorded (to an accuracy of 5 %).NOTE 2 It is useful to know the mass per u

33、nit area of the masking tape so that this can be used to calculate the actual slurry surfacing mass.6) Slurry surfacing sample is removed from the masking tape, noting any residual binder or bond coat adhering to the masking tape.7) Samples of slurry surfacing shall be packed and stored so that no c

34、ontamination or damage to the sample takes place.A.2 Sample labellingThe sampling report shall contain the information given in Clause 4.6 BS EN 122741:2018This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other

35、 standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovato

36、rs and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose stand

37、ards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and

38、download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered fr

39、om our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has forma

40、lly licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion ther

41、eof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 d

42、evice provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal o

43、r internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription pr

44、oduct (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products

45、 go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.You can keep in touch with standards developments and receive substanti

46、al discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member.PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.T

47、o find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre avai

48、lable, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: knowledgecentrebsigroup