EN 12229-2014 en Surfaces for sports areas - Procedure for the preparation of synthetic turf and needle-punch test pieces《运动场地面 人工草皮和针刺试件的制备过程》.pdf

《EN 12229-2014 en Surfaces for sports areas - Procedure for the preparation of synthetic turf and needle-punch test pieces《运动场地面 人工草皮和针刺试件的制备过程》.pdf》由会员分享，可在线阅读，更多相关《EN 12229-2014 en Surfaces for sports areas - Procedure for the preparation of synthetic turf and needle-punch test pieces《运动场地面 人工草皮和针刺试件的制备过程》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN 12229:2014Surfaces for sports areas Procedure for the preparationof synthetic turf and needle-punch test piecesBS EN 12229:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 12229:2014. Itsupersedes BS EN 12229:2007 which is with

2、drawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/57, Surfaces for sports areas.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract.

3、 Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 76837 8ICS 59.080.60; 97.150; 97.220.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published u

4、nder the authority of theStandards Policy and Strategy Committee on 31 January 2014.Amendments issued since publicationDate Text affectedBS EN 12229:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12229 January 2014 ICS 59.080.60; 97.220.10 Supersedes EN 12229:2007English Version Surfaces f

5、or sports areas - Procedure for the preparation of synthetic turf and needle-punch test pieces Sols sportifs - Mthode de prparation dprouvettes en textile aiguillet et en gazon synthtique Sportbden - Verfahren zur Herstellung von Probekrpern aus Kunststoffrasen und textilen Belgen This European Stan

6、dard was approved by CEN on 17 November 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concernin

7、g such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into it

8、s own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germa

9、ny, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR

10、NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12229:2014 EBS EN 12229:2014EN 12229:2014 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Terms and definition

11、s .4 3 Preparation of test pieces .4 4 Test report 8 BS EN 12229:2014EN 12229:2014 (E) 3 Foreword This document (EN 12229:2014) has been prepared by Technical Committee CEN/TC 217 “Surfaces for sports areas”, the secretariat of which is held by AFNOR. This European Standard shall be given the status

12、 of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2014, and conflicting national standards shall be withdrawn at the latest by July 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of

13、patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12229:2007. In comparison with the previous edition, the test method has been revised to more precisely define the design of the studded roller used within the t

14、est equipment. In particular, the positioning of the studs on the conditioning roller is now precisely specified. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgar

15、ia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turk

16、ey and the United Kingdom. BS EN 12229:2014EN 12229:2014 (E) 4 1 Scope This European Standard specifies a procedure for the preparation of test pieces of synthetic turf and needle-punch sports surfaces. 2 Terms and definitions For the purposes of this document, the following terms and definitions ap

17、ply. 2.1 surfacing top layer, or layers, including any shock pad or other shock absorbing or load spreading layers, which directly provide the sports performance and biomechanical response qualities 2.2 supporting layer(s) main structural layer or layers which support the surfacing and which can inf

18、luence its sports performance and biomechanical response qualities Note 1 to entry: Supporting layers can be composed of granular material with a binding agent to produce a cohesive layer or unbound granular material. 2.3 sample surfacing and supporting layers from which test pieces are taken 2.4 te

19、st piece representative specimen of the surfacing and any supporting layers, if required 3 Preparation of test pieces 3.1 Test pieces, with dimensions as specified in the appropriate test method, shall be cut from a sample of surfacing. Test pieces shall not be taken within 100 mm of any edge of a s

20、ample or its constituent parts. Test pieces shall be taken in an even distribution across the sample. 3.2 For tests in which the characteristics being measured are influenced by the supporting layers, as detailed in the appropriate test method, the surfacing shall be laid on supporting layers of equ

21、ivalent materials and construction to that used on an installation. The supporting layers of the test piece shall be prepared in accordance with the instructions provided by the manufacturer or supplier. When preparing the supporting layers, take care to ensure that the depth and consolidation of ma

22、terials simulates the conditions obtained during the installation of the product. If laboratory test pieces incorporating the supporting layers are being prepared in containers, take care to ensure that the design of the container does not influence the test results. 3.3 The surfacing shall be laid

23、free of creases and with minimal disturbance or damage onto the supporting layers. Record in the test report any creases or defects resulting from the manufacturing of the surfacing. Reject the surfacing if it has any defects resulting from storage or transportation. BS EN 12229:2014EN 12229:2014 (E

24、) 5 3.4 If the carpet pile is filled with the same filler material throughout its depth, the mass of filling material specified by the manufacturer or supplier, appropriate to the size of the sample, shall be taken and divided into three equal portions. One third shall be uniformly spread onto the s

25、urfacing working it into the pile with a stiff brush. This operation shall be repeated twice more until all filler is applied. Take care to ensure that applying the filler material does not flatten or trap the pile of the surfacing. 3.5 If different types of filler material are incorporated into the

26、 pile, the manufacturers instructions for preparing the surface shall be followed as closely as possible. If specified, this may include consolidation of the infill by means of a conditioning roller (see below) or other means. The same conditioning procedure shall be used on all test specimens being

27、 prepared for any one product. Take care to ensure that applying the filler material does not flatten or trap the pile of the surfacing. 3.6 Following filling, filled test specimens shall be conditioned prior to test by passing a hand-pulled roller over the test specimen for 50 cycles (one cycle com

28、prises one outward and one return path of one roller). The barrel of the roller shall weigh (28,5 0,5) kg, be (118 5) mm in diameter and have plastic studs mounted as shown in Figure 1 and detailed in Table 1. The studs shall be as shown in Figure 2, be manufactured from plastic and have a Shore A h

29、ardness of 96 2. Note a manufacturing tolerance of 1 mm for the stud positions has been found satisfactory. BS EN 12229:2014EN 12229:2014 (E) 6 Figure 1 Pattern of studs BS EN 12229:2014EN 12229:2014 (E) 7 Table 1 Coordinates of stud positions (centre of stud) STUD - X AXIS - Y AXIS STUD - X AXIS -

30、Y AXIS STUD - X AXIS - Y AXIS mm mm mm mm mm mm 1 154,5 0,0 51 279,5 127,5 101 150,0 252,5 2 271,5 4,5 52 255,5 128,5 102 78,5 252,5 3 35,0 8,5 53 185,5 129,5 103 31,0 259,0 4 198,5 10,5 54 92,5 134,5 104 242,5 264,5 5 246,0 13,5 55 139,0 136,5 105 289,0 268,0 6 105,0 14,0 56 22,0 141,0 106 195,0 27

31、0,5 7 11,5 16,0 57 65,5 146,5 107 7,5 271,0 8 128,5 19,0 58 231,5 149,0 108 125,0 271,0 9 79,0 23,0 59 114,5 149,5 109 101,0 274,5 10 55,0 23,0 60 208,0 151,0 110 51,5 275,5 11 173,0 24,0 61 159,5 152,5 111 169,5 280,5 12 222,0 25,0 62 42,0 157,5 112 219,0 280,5 13 267,0 30,0 63 276,0 158,5 113 76,0

32、 282,0 14 149,0 33,5 64 182,5 160,0 114 263,5 284,0 15 289,5 37,0 65 252,5 162,5 115 145,5 285,0 16 196,0 40,0 66 89,0 164,0 116 28,0 291,5 17 31,0 41,0 67 135,0 170,0 117 286,0 297,0 18 102,0 43,5 68 18,5 173,0 118 239,0 298,5 19 242,0 46,0 69 63,0 177,5 119 192,0 300,0 20 8,5 47,0 70 111,0 179,5 1

33、20 98,0 304,0 21 125,0 52,5 71 204,5 180,0 121 121,0 304,0 22 76,0 54,0 72 229,0 180,5 122 48,5 308,0 23 169,0 55,0 73 155,5 184,5 123 166,0 312,0 24 52,0 56,0 74 178,5 188,5 124 72,0 312,5 25 218,5 57,5 75 272,5 189,0 125 215,0 313,5 26 263,0 63,0 76 38,5 190,5 126 260,0 316,0 27 286,0 67,0 77 85,0

34、 192,5 127 142,0 319,5 28 146,0 68,5 78 249,0 196,5 128 21,0 329,0 29 193,0 70,5 79 131,5 204,5 129 113,0 333,0 30 98,5 75,0 80 14,5 207,0 130 64,5 336,0 31 28,0 75,5 81 294,5 208,0 131 180,0 340,0 32 5,5 78,0 82 58,5 210,5 132 231,0 340,0 33 239,0 81,0 83 201,0 210,5 133 87,0 342,5 34 122,0 85,0 84

35、 108,5 212,5 134 275,0 343,5 35 73,0 85,5 85 226,0 215,0 135 157,5 345,5 36 166,0 88,0 86 153,0 218,0 136 40,0 352,0 37 215,0 88,0 87 270,0 220,0 137 251,0 357,5 38 48,5 89,5 88 176,5 220,5 138 204,0 358,5 39 259,5 96,0 89 82,0 222,5 139 110,0 362,5 40 283,0 97,5 90 34,5 224,5 140 16,5 362,5 41 189,

36、0 100,0 91 246,0 231,0 141 133,0 363,5 42 142,0 103,0 92 128,5 237,5 142 61,0 368,0 43 94,5 104,0 93 292,0 237,5 143 177,5 369,0 44 25,5 109,0 94 12,0 238,5 144 84,5 370,0 45 235,0 114,5 95 199,0 241,0 145 228,0 370,0 46 69,5 116,0 96 104,0 242,0 47 118,5 117,5 97 55,0 243,0 48 162,5 119,5 98 222,0

37、248,0 49 211,5 119,5 99 172,5 250,0 50 46,0 123,5 100 266,5 252,5 BS EN 12229:2014EN 12229:2014 (E) 8 Dimensions in millimetres Figure 2 Stud profile 3.7 Following conditioning, the surface of the carpet shall be brushed in two directions at 90 to each other with a stiff brush to lift the pile befor

38、e testing. 4 Test report If information on the method of sample preparation is reported, it shall include the following: a) number and date of this European Standard, i.e. EN 12229:2014; b) complete identification of the surfacing, including type and manufacturers reference; c) materials from which

39、and the method in which the supporting layers of the test piece were constructed, if applicable; d) type and method of particulate filling; e) any damage or defects in the test piece; f) thickness and height of each infill layer; g) number of conditioning cycles undertaken. This page deliberately le

40、ft blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institut

41、ion (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully

42、 assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out mor

43、e about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies

44、can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further informati

45、on on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards de

46、velopments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards

47、when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updat

48、es supplied as soon as theyre available, you can be sure your documentation is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business

49、. If you find an inaccuracy or ambiguity within a British Standard or other BSI publication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licens