EN 10263-5-2017 en Steel rod bars and wire for cold heading and cold extrusion - Part 5 Technical delivery conditions for stainless steels.pdf

《EN 10263-5-2017 en Steel rod bars and wire for cold heading and cold extrusion - Part 5 Technical delivery conditions for stainless steels.pdf》由会员分享，可在线阅读，更多相关《EN 10263-5-2017 en Steel rod bars and wire for cold heading and cold extrusion - Part 5 Technical delivery conditions for stainless steels.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Steel rod, bars and wire for cold heading and cold extrusionPart 5: Technical delivery conditions for stainless steelsBS EN 102635:2017National forewordThis British Standard is the UK implementation of EN 102635:2017. I

2、t supersedes BS EN 102635:2001, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee ISE/106, Wire Rod and Wire.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include al

3、l the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 85298 5ICS 77.140.60; 77.140.65Compliance with a British Standard cannot confer immunity from legal obligations.Th

4、is British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 102635:2017EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 102635November 2017ICS 77.140.60

5、; 77.140.65 Supersedes EN 102635:2001EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCENCENELEC Management Centre: Avenue Marnix 17, B1000 Brussels 2017 CEN Ref. No. EN 102635:2017: EAll rights of exploitation in any form and by any means reserved wo

6、rldwide for CEN national MembersSteel rod, bars and wire for cold heading and cold extrusion Part 5: Technical delivery conditions for stainless steelsBarres, fil machine et fils en acier pour transformation froid et extrusion froid Partie 5: Conditions techniques de livraison des aciers inoxydables

7、Walzdraht, Stbe und Draht aus Kaltstauch und Kaltfliepresssthlen - Teil 5: Technische Lieferbedingungen fr nichtrostende SthleThis European Standard was approved by CEN on 4 September 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for gi

8、ving this European Standard the status of a national standard without any alteration. Uptodate lists and bibliographical references concerning such national standards may be obtained on application to the CENCENELEC Management Centre or to any CEN member.This European Standard exists in three offici

9、al versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Au

10、stria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Sp

11、ain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN 102635:2017 (E)European forewordThis document (EN 10263-5:2017) has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretariat of which is held by AFNOR.This European Standard shall be given the status

12、 of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2018, and conflicting national standards shall be withdrawn at the latest by May 2018.Attention is drawn to the possibility that some of the elements of this document may be the subject of pat

13、ent rights. CEN shall not be held responsible for identifying any or all such patent rights.This document supersedes EN 102635:2001.This European Standard EN 10263, Steel rod, bars and wire for cold heading and cold extrusion, is subdivided as follows: Part 1: General technical delivery conditions;

14、Part 2: Technical delivery conditions for steels not intended for heat treatment after cold working; Part 3: Technical delivery conditions for case hardening steels; Part 4: Technical delivery conditions for steels for quenching and tempering; Part 5: Technical delivery conditions for stainless stee

15、ls.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,

16、Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.2BS EN 102635:2017EN 102635:2017 (E)European foreword 2European foreword 41 S

17、cope . 52 Normative references 53 Terms and definitions . 54 Classification and designation . 54.1 Classification . 54.2 Designation 55 Production Process 56 Requirements 66.1 Delivery conditions . 66.2 Chemical composition 66.2.1 Cast analysis . 66.2.2 Product analysis . 66.3 Mechanical properties

18、66.4 Surface quality . 66.5 Supplementary or special requirements 66.5.1 Aptitude to cold forming . 66.5.2 Depth of surface discontinuities . 73Contents PageBS EN 102635:2017EN 102635:2017 (E)European forewordThis document (EN 10263-5:2017) has been prepared by Technical Committee ECISS/TC 106 “Wire

19、 rod and wires”, the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2018, and conflicting national standards shall be withdrawn at the latest by May 2018

20、.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights.This document supersedes EN 102635:2001.This European Standard EN 10263, Steel rod, bars and wire for

21、 cold heading and cold extrusion, is subdivided as follows: Part 1: General technical delivery conditions; Part 2: Technical delivery conditions for steels not intended for heat treatment after cold working; Part 3: Technical delivery conditions for case hardening steels; Part 4: Technical delivery

22、conditions for steels for quenching and tempering; Part 5: Technical delivery conditions for stainless steels.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

23、Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

24、Turkey and the United Kingdom.4BS EN 102635:2017EN 102635:2017 (E)1 Scope1.1 This European Standard is applicable to round rod, round bars and wire made of stainless steels intended for cold heading and cold extrusion having a diameter up to and including: 25 mm for ferritic and austeniticferritic s

25、teels; 50 mm for austenitic steels; 100 mm for martensitic steels.1.2 EN 102631 is indispensable for the application of this part of EN 10263.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For

26、 dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 10020, Definition and classification of grades of steelEN 100881:2014, Stainless steels Part 1: List of stainless steelsEN 102631:2017, Steel

27、 rod, bars and wire for cold heading and cold extrusion Part 1: General technical delivery conditions3 Terms and definitionsFor the purposes of this document, the terms and definitions given in EN 10263-1 and the following apply.3.1stainless steelssteels with at least 10,5 % Cr and max. 1,2 % C (mas

28、s fraction)4 Classification and designation4.1 ClassificationAll steels covered by this part of EN 10263 are stainless steels according to EN 10020.From a practical viewpoint these steels are also classified on the basis of their structure; see also EN 100881:2014, Annex C.4.2 DesignationSee EN 1026

29、31.5 Production ProcessSee EN 102631.5BS EN 102635:2017EN 102635:2017 (E)6 Requirements6.1 Delivery conditionsThe delivery conditions in which the products covered by this part of EN 10263 are normally supplied, the product forms and the applicable requirements are given in Table 1 and Table 2.6.2 C

30、hemical composition6.2.1 Cast analysisThe chemical composition shall be in accordance with the values specified in Table 3 for the cast analysis.6.2.2 Product analysisIn cases where a product analysis is requested, the admissible deviations from the values specified for the cast analysis are indicat

31、ed in Table 4.6.3 Mechanical propertiesThe mechanical properties of the products, to be determined by the tensile test, shall be in accordance with the prescriptions given in Table 5, Table 6, Table 7 and Table 8.6.4 Surface quality6.4.1 Rod is normally supplied in the pickled condition. Mechanical

32、descaling (sandblasting) can also be used, in which case a subsequent treatment in a pickling solution shall be carried out unless otherwise agreed. Particular processes such as peeling or shaving may also be applied, subject to specific agreement at the time of enquiry and order.6.4.2 Minor surface

33、 imperfections which may occur under normal manufacturing conditions, such as scores originating from rolledin scale, shall not be regarded as defects.6.4.3 Any particular surface requirements may be agreed at the time of enquiry and order.6.5 Supplementary or special requirements6.5.1 Aptitude to c

34、old formingA test for the verification of the aptitude of products to cold forming may be carried out if agreed at the time of enquiry and order.If for the verification of the aptitude to cold forming the upsetting test is applied, it shall be carried out as follows: a test piece with an initial len

35、gth (height) equal to 1,5 x d, where d is the product diameter, is submitted to axial heading by means of a press until its length is reduced to 1/3 of the initial value.The above test shall be carried out at ambient temperature and limited to the products with a maximum diameter of 15 mm.The criter

36、ia for the assessment of test results shall be agreed at the time of ordering bearing in mind the end use for which the products are intended.6 BS EN 102635:2017EN 102635:2017 (E)6.5.2 Depth of surface discontinuitiesThe maximum admissible depth of surface discontinuities is indicated in Table 9. Th

37、e depth of a discontinuity is considered as being the distance between the surface of the product and the bottom of the discontinuity, to be measured in a direction perpendicular to the surface along a radius. In case of dispute the determination of the depth of surface discontinuities shall be carr

38、ied out by metallographic means with a magnification of X 100, on a straight cross section of the product in the delivery condition concerned.7BS EN 102635:2017EN 102635:2017 (E)Table1 Combination of usual heattreatment conditions, product forms and applicable requirementsHeattreatmentconditionatdel

39、iverySymbolProduct formaSteelsApplicablerequirementsbarrodwireferriticmartensiticaustenitic and austeniticferriticSoftannealed+AXXXXXChemicalcomposition as specified in Table3Mechanicalproperties as specified in Table5or6or7or8Supplementaryorspecialrequirements as specified in EN10263-1:2017, AnnexA

40、bSolutionannealed+ATXXXXOthersOther delivery conditions may be agreed at the time of enquiry and order.aX=applicable =not applicable bIf agreed at the time of the enquiry and order.8 BS EN 102635:2017EN 102635:2017 (E)Table2 Surface condition at deliverySurface condition at deliverySymbolbarrodwireC

41、olddrawn+CxxPeeled+PExxSkin passed+LCx9BS EN 102635:2017EN 102635:2017 (E)Table3 Steel grades and chemical composition Cast analysis, % by mass aSteel gradeCSiMnPSCrMoNiNCuOthersSteelnameSteelnumberAusteniticsteelsX10CrNi1881.43100,05 to 0,152,002,000,0450,01516,0 to 19,00,806,0 to 9,50,101,00X2CrNi

42、1891.43070,0301,002,000,0450,030b17,5 to 19,58,0 to 10,50,101,00X2CrNi19111.43060,0301,002,000,0450,030b18,0 to 20,010,0 to 12,00,101,00X5CrNi18101.43010,071,002,000,0450,030b17,5 to 19,58,0 to 10,50,101,00X6CrNiTi18101.45410,081,002,000,0450,030b17,0 to 19,09,0 to 12,01,00Ti=5xC to 0,70X4CrNi18121.

43、43030,061,002,000,0450,030b17,0 to 19,011,0 to 13,00,10X2CrNiMo 171221.44040,0301,002,000,0450,030b16,5 to 18,52,00 to 2,5010,0 to 13,00,101,00X2CrNiMo171231.44320,0301,002,000,0450,030b16,5 to 18,52,50 to 3,0010,5 to 13,00,101,00X5CrNiMo171221.44010,071,002,000,0450,030b16,5 to 18,52,00 to 2,5010,0

44、 to 13,00,101,00X6CrNiMoTi171221.45710,081,002,000,0450,030b16,5 to 18,52,00 to 2,5010,5 to 13,51,00Ti=5xC to 0,70X2CrNiMoN171331.44290,0301,002,000,0450,01516,5 to 18,52,50 to 3,0011,0 to 14,00,12 to 0,221,00X3CrNiMo171331.44360,051,002,000,0450,030b16,5 to 18,52,50 to 3,0010,5 to 13,00,10aMaximum

45、values unless indicated otherwise. bParticular ranges of sulphur content may provide improvement of particular properties. For machinability a controlled sulphur content of 0,015% to 0,030% is recommended and permitted. For weldability, a controlled sulphur content of 0,008% to 0,030% is recommended

46、 and permitted. For polishability, a controlled sulphur content of 0,015% max. is recommended. cIn order to improve the cold formability, a carbon content of max 0,04% is recommended and may be agreed at the time of enquiry and order. dBy agreement, this grade can be delivered with a Pitting Resista

47、nce Equivalent Number (PRE=Cr + 3,3 Mo + 16N, compare EN10088-1:2014, TableD.1) greater than 34. eA minimum content of 8% of Ni is permitted, unless otherwise agreed at the time of enquiry and order. 10 BS EN 102635:2017EN 102635:2017 (E)Steel gradeCSiMnPSCrMoNiNCuOthersSteelnameSteelnumberX3CrNiCu1

48、89-41.45670,041,002,000,0450,030b17,0 to 19,08,5 to 10,5 e0,103,00 to 4,0X3CrNiCu199-21.45600,0351,001,50 to 2,000,0450,01518,0 to 19,08,0 to 9,00,101,50 to 2,00X3CrNiCuMo17113-21.45780,041,002,000,0450,01516,5 to 17,52,00 to 2,5010,0 to 11,00,103,00 to 3,5AusteniticferriticsteelX2CrNiMoN225-3d1.446

49、2d0,0301,002,000,0350,01521,0 to 23,02.50 to 3.54,5 to 6,50,10 to 0,22FerriticsteelsX6Cr171.40160,08c1,001,000,0400,030b16,0 to 18,0X6CrMo1711.41130,081,001,000,0400,030b16,0 to 18,00,90 to 1,40MartensiticsteelX12Cr131.40060,08 to 0,151,001,500,0400,030b11,5 to 13,50,75Elements not quoted in this table may not be intentionally added to the steel without the agreement of the purchaser except for finishing the heat. All appropriate pre