ECA 186-3E-1978 Passive Electronic Component Parts Test Methods for Method 3 Humidity (Steady State-Sealed Container).pdf

《ECA 186-3E-1978 Passive Electronic Component Parts Test Methods for Method 3 Humidity (Steady State-Sealed Container).pdf》由会员分享，可在线阅读，更多相关《ECA 186-3E-1978 Passive Electronic Component Parts Test Methods for Method 3 Humidity (Steady State-Sealed Container).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、ANSI/EA RS-186-E-78 Approved October 27,1978 EIA STANDARD STANDARD TEST METHODS FOR PASSIVE ELECTRONIC COMPONENT PARTS RSn1863E METHOD 3: HUMIDITY (STEADY STATE-SEALED CONTAINER) I (Revision of RS-186-0, Method 3) OCTOBER 1978 Engineering Depurtment EEBCTRONIC INDUSTRIES ASSOCIATION - EIA Lb-3E 78 M

2、 3234600 0028588 2 .- NOTICE EIA engineering standards are designed to serve the public interest through eliminating mis- understandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with mini

3、- mum delay the proper product for his particular need. Existence of such standards shall not in any respect preclude any member or non-member of EIA from manufacturing or selling products not conforming to such standards, nor shall the existence of such standards pre- clude their voluntary use by t

4、hose other than EIA members whether the standard is to be used domestically or internationally. Recommended standards are adapted by EIA without regard to whether or not their adop- tion may involve patents on articles, materials, or processes. By such action, EU does not assume any liability to any

5、 patent owner, nor does it assume any obligation whatever to partis adopting the recommended standards. This EIA Standard is considered by the Formulating Committee not to have international standards implication or interest. .LECTRBN I c Publbhed by ASSOCOATIQN Engineering Degrsrtment 2001 Eye Stre

6、ot, N:W, Wsebingtan, D, C, 20006 PRICE: $3.00 EIA l8b-3E 78 m 3234600 0028589 4 m a- RS-186-33 Page 1 STANDARD TEST METHODS FOR PASSIVE ELECTRONIC COMPONENT PARTS METHOD 3 HUMIDITY (STEADY STATE-SEALED CONTAINER) (From EIA Standard RS-186-0 and Standards Proposal No. 1271 formulated under the cogniz

7、ance of the EIA P-9 Committee on Test Methods and Procedures.) INTRODUCTION This Test Method forms a part of the EIA Standard RS-186 which contains test guidance, definitions and standard test conditions. 1. PURPOSE This test is intended to evaluate the effect of absorption and diffusion of moisture

8、 and moisture vapor on component parts. The test is an artificial environmental test and is severely accelerated to shorten testing time. This test is more severe than Method 1. This test is of value in determining the resistance of the component parts to the inroads of moisture, but should not be c

9、onsidered as a tropical test for all types of component parts. This test method provides a means of performing humidity testing without the need for specialized humidity test equipment. 2. PROCEDURE 2.1 Mounting - Unless otherwise specified in the individual specification, specimens shall be mounted

10、 by their normal mounting means. 2.2 Pre-Conditioning and Initial Measurements - Unless otherwise specified, the specimens shall be conditioned at a temperature of 50 I5“C (122 *9F) for a period of 24 hours. At the.end of this period, specimens shall be allowed to thermally stabifize under the stand

11、ard conditions of test, and initial measurements shall then be made if specified in the individual specification, 2.3 Exposure - The specimens shall be supported in a tightly-closed container (a 0.031 in. (0.79mm) pressure relief hole is recommended) with distilled or dionized water in the bottom. T

12、he container with the specimens shall then be placed in an insulated oven at 66 t3“C (151“ k5.4“F). Forced ventilation shall be provided within the oven to insure uniform temperature. The specimens shall be subjected to this exposure for one of the standard periods of time indicated below. Unless ot

13、herwise specified 240 hours shall be used. 48 hours 96 hours 240 hours A tolerance of +3% on the total time. shall be allowed. 2.4 Loading and Polarizing Voltages - As specified in the individual specification, voltage shall be applied to r the specimens during the exposure period: the magnitude and

14、 points of application shall be as specified. 2.5 Post-Conditioning - After removal from the oven and the closed container, the specimens shall have their surface moisture removed by circulating air at room temperature or wiping with a clean cloth, or both. The specimens shall then be allowed to the

15、rmally stabilize under the standard conditions of test. EIA l186-3E 78 = 3234600 0028590 O = RS-186-3E Page 2 2.6 Final Measurements - At the completion of a period of thermal stabilization, final measurements shall a be made. The period of stabilization shall not be less thari 1 hour nor more than

16、2 hours unless other- wise specified. The method of measurement shall be as shown in the detailed component standard. 3. SUMMARY The following details shall be specified in the individual specification. 3.1 Preconditioning/requirements if standard conditions (2.2) are not applicable. 3.2 Initial measurements after conditioning (2.2). 3.3 Magnitude of voltage and points of application, if applicable (2.4). 3.4 Exposure duration (2.3) if other than 240-hours. 3.5 Final measurements after exposure (2.6).