DOD A-A-54337-1991 SHEET BED (COTTON-POLYESTER WHITE FITTED)《床单(合适的白色棉花聚酯)》.pdf

《DOD A-A-54337-1991 SHEET BED (COTTON-POLYESTER WHITE FITTED)《床单(合适的白色棉花聚酯)》.pdf》由会员分享，可在线阅读，更多相关《DOD A-A-54337-1991 SHEET BED (COTTON-POLYESTER WHITE FITTED)《床单(合适的白色棉花聚酯)》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、e l a l l I AMSC N/A FSC 7210 DISTRIBUTION STATEMENT A: Approved for public release: distribution is unlimited. A-A-54337 72 m 9799974 00b0307 1 m A-A-54337 14 February 1991 COMMERCIAL ITEM DESCRIPTION SHEET, BED (Cotton-Polyester, White, Fitted) The General Services Administration has authorized th

2、e use of this Commercial Item Description as a replacement for MIL-S-36868 which is cancelled. This Commercial Item Description covers a fitted, white cotton- polyester bed sheet. Salient Characteristics: The bed sheet shall be a bleached, white, shrunk, polyester/ cotton sheet of fitted or preshape

3、d configuration, made of commercial permanent-press or non-resinous material designation No. 128 (muslin), suitable for use as a bottom sheet on hospital beds. The sheet shall be supplied in the following sizes: Size Width Length (cut or torn) 1 46 inches +i inch 91 inches Li inch 2 52 inches 51 inc

4、h 94 inches 51 inch The yarn shall be an intimate blend of polyester and cotton fiber, consisting of 50 plus or minus 5 percent polyester and the remaining percentage cotton. The sheeting shall have the following characteristics: Provided by IHSNot for ResaleNo reproduction or networking permitted w

5、ithout license from IHS-,-,- _ A-A-54337 72 9999974 0060308 3 A-A-54337 Characteristic Requ i remen t Weight 3.5 ounces/square yard minimum Total yarns per square inch 128 minimum Ends per inch 68 nominal Picks per inch 60 nominal Breaking strength Warp Filling 55 pounds minimum 55 pounds minimum We

6、ave Plain Dimensional stability Warp Fil 1 ing 2 percent shrinkage maximum 2 percent shrinkage maximum The thread for all the sewing operations shall be cotton- covered polyester thread ticket number 70. 2 ply; or spun polyester thread, ticket number 70. 2 or 3 ply. The color of the thread shall be

7、orange TL. C.A. 66076. The sheet shall have a 35 gauge heat resist.ant rubber elastic, 1/4 to 3/8 inch wide, secured across each end, including the corners, with a suitable bias binding tape to provide a snug fit over the following size mattresses: Size 1 - 30 by 75 by 7 inches Size 2 - 36 by 78 by

8、6-1/2 inches All hems shall be straight and of uniform width. Hems shall be sewn so that no raw edges, run-offs, twists, pleats, puckers, or open seams result. Ends of all seams and stitchings, when not caught in other seams or stitchings, shall.be backtacked or backstitched not less than 1/2 inch.

9、Thread breaks shall be secured by stitching back of the breaks not less than 1/2 inch at each break. All thread ends shall be trimmed to a length of not more than 1/2 inch. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-54337 72 m 9999974 O060

10、309 5 m A-A-54337 A permanent launderable identification label shall be attached to the sheet. The label shall be approximately centered and sewn into the top or bottom hem of each sheet. The top or bottom edge of the label may be caught in the hem stitching. If desired, the remaining three sides ma

11、y be sewn to the sheet. As an alternate, the label may be attached by positioning in approximately the same position as described above and stitching all four sides. The label shall show at least good colorfastness to laundering transference and.to accelerated laundering. The label shall contain the

12、 following information for the size 1 sheet: * Nomenclature - Sheet, Bed, Cotton-Polyester, * Material content - 50 percent polyester/50 percent * To fit mattress - 75 inches x 30 inches x 7 inches White, Fitted cotton For the size 2 sheet, the label shall read: * Nomenclature - Sheet, Bed, Cotton-P

13、olyester, W Material content - 50 percent Polyester/SO percent a To fit mattress - 78 inches x 36 inches x 6-1/2 inches White, Fitted Cotton As an alternate to the above, the identification label may be a standard commercial-type mill label. The label shall state as a minimum: * Fiber percentage * M

14、anufacturers name . W The phrase Made in U.S.A. If labeling is done on an automatic machine, the label may be sewn in one of the corners. The finished sheet, the unit of issue, shall be folded and packaged in a suitable polyethylene bag. 3 Provided by IHSNot for ResaleNo reproduction or networking p

15、ermitted without license from IHS-,-,- A-A-54337 72 99619974 00b03LO L = A- A- 54337 Workmanship. The bed sheet shall be free from defects which detract from its appearance or impair its serviceability. Unit. Each (EA). One sheet of the size specified, constitutes one unit. Quality Assurance Provisi

16、ons. Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in t.he contract or purchase order, the contractor may use his own or

17、any facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Qovernment. The Government reserves the right t,o perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and se

18、rvices conform to prescribed requirements. Records. Records of examinations and tests performed by or for the contractor shall be maintained by the contractor and made available to the Government upon the Governments request, at any time, or from time to time, during the performance of the contract

19、and for a period of three years after delivery of the supplies to which such records relate. Inspection. Inspection, as used herein, is defined as both examination (such as visual or auditory investigation without the use of special laboratory appliances or procedures) and testing (determination by

20、technical means of physical and chemical properties) of the item. Sampling for examination. Sampling for examination shall be conducted in accordance with MIL-STD-105, with an AQL of 4.0 (percent defective) and an inspection level of I. The unit of product for examination purposes shall be one bed s

21、heet. Sampling for tests. Sampling for tests, including dimensional test, shall be conducted in accordance with MIL-CTD-105. with an AQL of 2.5 (percent defect.ive) and an inspection level of S-3. The unit of product for test purposes shall be one bed sheet. 4 Provided by IHSNot for ResaleNo reprodu

22、ction or networking permitted without license from IHS-,-,-A-A-54337 I A-A-54337 72 m 9999974 0060311 3 m Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, providing they fall within the tolerances specifi

23、ed using conversion tables contained in the latest revision of Federal Standard 376, and all other requirements of this document are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch/pound units, a request should be made to the co

24、ntracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. . Contractor certification. The contractor shall certify that the product offered meets the salient characteristics of this description and conforms to the produ

25、cers own drawings, specifications, standards, and quality assurance practices. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Regulatory requirements. a Federal Food,

26、 Drug and Cosmetic Act. If the product covered by this document has been determined by the U.S. Food and Drug Administration to be under its jurisdiction, the offeror/contractor shall comply, and be responsible for compliance by its subcontractorssuppliers, with the requirements of the Federal Food,

27、 Drug and Cosmetic Act, as amended, and regulations promulgated thereunder. In addition. the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of all other applicable Federal, State, and local statutes, ordinances and regulation

28、s. Recovered materials. The offeror/contractor is encouraged to use recovered material in accordance with Federal Acquisition Regulation Subpart 23.4 to the maximum extent practical. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-54337 Preserv

29、ation, packaging, D acking. labeling. and marking. Unless otherwise specified, preservation, packaging, and packing shall be to a degree of protection to preclude damage to containers and/or contents thereof under normal shipping conditions, handling, etc., involving shipment from the supply source

30、to the receiving activity, plus reshipment from receiving activity, and shall conform to applicable carriers rules and regulations. Intermediate and exterior package quantities and labeling and marking shall be as specified in the contract and/or order. Ordering data, Intermediate/exterior package q

31、uantities, labeling, and marking must be specified in the contract and/or order. NOTE: The following National Stock Numbers are covered by this document. 7210-00-119-7361 (Size 1) 7210-00-1 19-7369 (Size 2) MILITARY INTERESTS : PREPARING ACTIVITY: Custodians: Army - MD Navy - MS Air Force - 03 DoD-MB Agent: DLA-DU CIVIL AGENCY COORDINATING ACTIVITIES: VA-OSS USPHS FDA - MPQ AS Project Number: 7210-0289 Location: SHEETCID.13A 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-