DOD A-A-53848-1989 TUBING NONMETALLIC (RUBBER)《非金属物质试管(橡胶)》.pdf

《DOD A-A-53848-1989 TUBING NONMETALLIC (RUBBER)《非金属物质试管(橡胶)》.pdf》由会员分享，可在线阅读，更多相关《DOD A-A-53848-1989 TUBING NONMETALLIC (RUBBER)《非金属物质试管(橡胶)》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-53848 47 m 7797774 0036337 O m A-A-538 48 3 March 1989 COMMERCIAL ITEM DESCRIPTION TUBING, NONMETALIC (Rubber) The General Services Administration.has authorized the use of this commercial item description as a replacement for military specification MIL-T-36966 which has been canceled. This comm

2、ercial item description covers two sizes of latex rubber tubing suitable for laboratory use. Salient characteristics. The tubing shall be fabricated of natural rubber latex without any added coloration. section and free from porosity. surfaces shall be smooth and free of powder, dust, oil, grease, i

3、mpair its serviceability. strength of at least 1200 p.s.i. and an ultimate elongation of at least 750 percent. sizes and dimensions. The tubing shall be of uniform cross- The inside and outside The tubing shall have a tensile The tubing shall be of the following . dirt, fins and any foreign matter o

4、r surface defect which Size Inside diameter 1/8 inch 3/16 inch 1/8 3/16 Wall thickness Tolerance + 1/128 inch + 1/64 inch - 1/32 inch 3/32 inch - Workmanship. The tubing shall be free from defects which detract from its appearance or impair its serviceability. Unit. Foot (FT). One linear foot of tub

5、ing, as specified, constitutes one unit. AMSC N/A FSC 4720 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. / 7 THIS DOCUMENT CONTAINS 3 PAGES. - Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without lic

6、ense from IHS-,-,-A-A-5 3 8 4 8 Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured wing inch-pound units, providing they fall within the tolerances specified using conversion tables contained in the latest revision o Federal Stand

7、ard 376, and all other requirements of this document are met, If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the esnixacting officer to determine if the product is acceptable. The contracting

8、 officer has the option of accepting OK rejecting Contractor certification. The contractor shall certify that the pmduct oEfered meets the salient characteristics of this description and conforms to the producers own drawings, specificationsr standards, and quality assurance practices. The Governmen

9、t reserves the right to require proof of such conformance prior to first: delivery and thereafter as may be otherwise provided for under the provisions of the contract. the product Regulatory requirements. If the product covered by this document has been determined by the U, S, Food and Drug Adminis

10、tration to be under its jurisdiction, the offeror/ contractor shall comply, and be responsible for compliance by its Gubesntractors/suppliers, with the requirements of the Federal Food, Drug and Cosmetic Act, as amended, and regulations promulgated thereunder. In addition, the offeror/contractor sha

11、ll complyr and be responsible or compliance by its subcontractor/suppliers, with the requirements of all other applicable Federal, State and local statutes, ozdinanees, and iegulations, Recovered materials. The ofersr/contractor is encouraged to use recovered material in accordance with Public Law 9

12、4-580, as amended, and as implemented by Federal Acquisition Regulation Subpart 23.4 to the maximum extent practical. Pedeia1 Foodr Drug and Cosmetic Act Preservation, packaging, p acking, labeling, and markinq, Unless otherwise specified, preservation, packagingr and packing shall be ta a degKee of

13、 protection to pieclude damage to containers and/or contents thereof under normal shipping conditions, handling, etc., involving shipment from the supply source to the receiving activity, plus reshipment from receiving activity, and shall confoEm to applicable carriers rules and regulations. Interme

14、diate and exterior package quantities and labeling and marking shall be as specified in the contract and/or order. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- .- - - A-A-53LI 47 7777774 003b337 4 A-A-53 8 40 NOTE: The following National Stock

15、Numbers are covered by this document: 4720-00-141-9070 TUBING, NONMETALIC, Rubber Size 1/8 4720-00-141-9080 TUBING, NONMETALIC, Rubber Size 3/32 Orderinq data. (Intermediate/exterior package quantities and labeling and marking must be specified in the contract and/or order). MILITARY INTERESTS: PREP

16、ARING ACTIVITY: DoD - MB Custodians: Army - MD Agent: Navy - MS Air Force - 03 . DLA-DM CIVIL AGENCY COORDINATING ACTIVITIES: VA-OSS PHS FDA-MPQAS Project No. 4720-0766 Location: Disk No. 16 CID/TUBING/S3D 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-