DLA SMD-5962-99550 REV C-2011 MICROCIRCUIT HYBRID LINEAR 15 VOLT SINGLE CHANNEL DC DC CONVERTER.pdf

《DLA SMD-5962-99550 REV C-2011 MICROCIRCUIT HYBRID LINEAR 15 VOLT SINGLE CHANNEL DC DC CONVERTER.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-99550 REV C-2011 MICROCIRCUIT HYBRID LINEAR 15 VOLT SINGLE CHANNEL DC DC CONVERTER.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Table I, Efficiency test, change minimum limit for subgroup 1 from 86% to 84% and subgroups 2, 3 from 85% to 83%. Update drawing boilerplate. 03-05-28 Raymond Monnin B Table I; Changed the maximum limit for the line regulation test (VRLINE) from

2、20 mV to 40 mV for subgroups 2 and 3. Changed the maximum limit for the load regulation test (VRLOAD) from 20 mV to 30 mV for subgroup 1 and add 100 mV for the maximum limit for subgroups 2 and 3. Update drawing to the latest requirements. -sld 05-12-13 Raymond Monnin C Added footnote 1 to table II,

3、 under group C end-point electricals. Updated drawing paragraphs. -sld 11-04-13 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve L. Duncan DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING C

4、HECKED BY Michael C. Jones COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, 15 VOLT, SINGLE CHANNEL, DC/DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 99-

5、05-18 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-99550 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E128-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99550 DLA LAND AND MARITIME COLUMBUS, OHIO 43

6、218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN)

7、. When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 99550 01 H T X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) desig

8、nator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s).

9、 The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 MOR2815S/883 DC/DC converter, 120 W, 15 V output 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are d

10、efined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is inten

11、ded for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Ins

12、pections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s)

13、taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality

14、level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99550 DLA LAND AND MARITIME COLUMBUS, OHI

15、O 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style T See figure 1 12 Tabbed flange mount, lead formed up U See figure 1 12 Flange mount,

16、 lead formed down X See figure 1 12 Flange mount, short lead Y See figure 1 12 Tabbed flange mount, short lead Z See figure 1 12 Tabbed flange mount, lead formed down 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage range (VIN)

17、 2/ -0.5 V dc to +50 V dc Power dissipation (PD) . 30 W Lead temperature (10 seconds) +300C Storage temperature . -65C to +150C 1.4 Recommended operating conditions. Input voltage range (VIN) . +16 V dc to +40 V dc Output power . 120 W Case operating temperature range (TC) -55C to +125C 2. APPLICABL

18、E DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT

19、OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of St

20、andard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precede

21、nce. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute max

22、imum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ An undervoltage lockout circuit shuts the unit off when the input voltage drops to approximately 14.5 volts. Operation of the unit between 14.5 volts and

23、 16 volts is nondestructive, but performance is not guaranteed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99550 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 AP

24、R 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Qualit

25、y Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification i

26、n the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s)

27、shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and sha

28、ll apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in acc

29、ordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall mainta

30、in the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained

31、 under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime- VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of

32、 compliance (original copy) submitted to DLA Land and Maritime- VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of

33、microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit,

34、or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99550 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical perfor

35、mance characteristics. Test Symbol Conditions -55C TC+125C VIN= 28 V dc 0.5 V dc no external sync, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTIOUT= 8 A dc 1 01 14.85 15.15 V 2,3 14.70 15.30 Output current IOUTVIN= 16, 28, and 40 V dc 1,2,3 0

36、1 8 A Output ripple voltage VRIPIOUT= 8 A, B.W. = 10 kHz to 20 MHz 1 01 130 mV p-p 2,3 150 Line regulation VRLINEIOUT=8 A VIN= 16 V dc to 40 V dc, 1 01 20 mV 2,3 40 Load regulation VRLOADIOUT= 0 to 8 A 1 01 30 mV 2,3 100 Input current IINIOUT= 0 A, inhibit 1 (pin 4) = 0 1, 2, 3 01 10 mA IOUT= 0 A, i

37、nhibit 2 (pin 12) = 0 70 IOUT= 0 A, inhibit 1 and 2 (pins 4 and 12) = open 150 Input ripple current IRIPIOUT= 8 A, B.W. = 10 kHz to 20 MHz 1 01 120 mA p-p 2, 3 130 Efficiency EFFIOUT = 8 A 1 01 84 % 2, 3 83 Isolation ISO Input to output or any pin to case at 500 V dc 1 01 100 M Capacitive load 1/ 2/

38、 CLNo effect on dc performance, 4 01 1000 F See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99550 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC F

39、ORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC+125C VIN= 28 V dc 0.5 V dc no external sync, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Power dissipation Short circuit PDShort circuit 1,2,3 01 20 W Sw

40、itching frequency FSIOUT= 8 A 4 01 480 580 kHz 5, 6 460 600 External sync range 3/ FSYNCIOUT= 8 A, TTL level to pin 6 4,5,6 01 525 625 kHz Output response to step transient load changes 4/ VTLOAD50 percent load to/from 100 percent load 4,5,6 01 -600 600 mV pk Recovery time step transient load change

41、s 2/ 4/ 5/ TTLOAD50 percent load to/from 100 percent load 4,5,6 01 300 s Output response to transient step line changes 2/ 6/ VTLINEIOUT= 8 A, Input step from 16 V dc to 40 V dc 4,5,6 01 -600 +600 mV pk IOUT= 8 A, Input step from 40 V dc to 16 V dc -600 +600 Recovery time, transient step line change

42、s 2/ 5/ TTLINEIOUT= 8 A, Input step from 16 V dc to 40 V dc 4,5,6 01 300 s IOUT= 8 A, Input step from 40 V dc to 16 V dc 300 Turn-on overshoot 3/ VtonosIOUT= 8 A, VIN= 0 to 28 V dc 4,5,6 01 50 mV pk Turn-on delay time 7/ TonDIOUT= 8 A, VIN= 0 to 40 V dc 4,5,6 01 10 ms Load fault recovery 2/ TrLFIOUT

43、= 8 A 4,5,6 01 10 ms 1/ Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. 2/ Parameter shall be tested as part of design characterization and after design or process changes; therefore, the parameter shall be guaranteed to the limits specified in table

44、 I. 3/ A TTL level waveform (VIH= 4.5 V minimum, VIL= 0.8 V maximum with a 50 percent 10 percent duty cycle applied to the sync input pin (pin 6) within the sync range frequency shall cause the converters switching frequency to become synchronous with the frequency applied to the sync input pin (pin

45、 6). 4/ Load step transition time is 50 microseconds minimum. 5/ Recovery time is measured from the initiation of the transient until VOUThas returned to within 1 percent of its final value. 6/ Input step transition time greater than 10 microseconds 7/ Turn-on delay time measurement is either for a

46、step application of power at the input or the removal of a ground signal from the inhibit 1 pin (pin 4) or inhibit 2 pin (pin 12) while power is applied to the input. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE

47、A 5962-99550 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outline T. Symbol Millimeters InchesMin Max Min MaxA 10.16 .400A1 5.33 5.84 .210 .230b 0.89 1.14 .035 .045D 50.55 51.05 1.990 2.010D1 37.85 38.35 1.490 1.510e 5.08 BSC .200 BSCE 69.85 72.

48、39 2.750 2.850E1 63.25 63.75 2.490 2.510F 1.14 1.40 .045 .055L 6.10 6.60 .240 .260P 3.43 3.68 .135 .145q/q1 44.32 44.58 1.745 1.755q2 29.08 29.34 1.145 1.155s 6.22 6.48 .245 .255T 9.91 12.45 .390 .490NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch- pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2