DLA SMD-5962-96825 REV A-2009 MICROCIRCUIT DIGITAL ADVANCED HIGH SPEED CMOS QUADRUPLE 2-INPUT POSITIVE-OR-GATE MONOLITHIC SILICON.pdf
《DLA SMD-5962-96825 REV A-2009 MICROCIRCUIT DIGITAL ADVANCED HIGH SPEED CMOS QUADRUPLE 2-INPUT POSITIVE-OR-GATE MONOLITHIC SILICON.pdf》由会员分享,可在线阅读,更多相关《DLA SMD-5962-96825 REV A-2009 MICROCIRCUIT DIGITAL ADVANCED HIGH SPEED CMOS QUADRUPLE 2-INPUT POSITIVE-OR-GATE MONOLITHIC SILICON.pdf(17页珍藏版)》请在麦多课文档分享上搜索。
1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update the boilerplate paragraphs to current MIL-PRF-38535 requirements and Editorial changes throughout. - MAA 09-01-28 Charles F. Saffle REV SHEET REV SHEET REV A A SHEET 15 16 REV A A A A A A A A A A A A A A REV STATUS OF SHEETS SHEET 1 2 3 4
2、5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby CHECKED BY Thanh V. Nguyen DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil APPROVED BY Monica L. Poelking DRAWING APPROVAL DATE 96-06-05 MICROCIRCUIT, DIGITAL, ADVANCED HIGH SPEED CMOS, QUADRUPLE 2-INPUT PO
3、SITIVE-OR-GATE, MONOLITHIC SILICON SIZE A CAGE CODE 67268 5962-96825 STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A REVISION LEVEL A SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E148-09 Provided by IHSNot for ResaleNo
4、 reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-96825 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels c
5、onsisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in th
6、e PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 96825 01 Q C A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device c
7、lasses Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-R
8、HA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AHC32 Quadruple 2-input positive-OR-gate 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance leve
9、l as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The
10、 case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specifi
11、ed in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-96825 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990
12、 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to +7.0 V dc 4/ DC output voltage range (VOUT). -0.5 V dc to VCC+ 0.5 V dc 4/ DC input clamp current (IIK) (VIN 0.0 V ) -20
13、mA DC output clamp current (IOK) (VOUT 0.0 V or VOUT VCC) 20 mA Continuous output current (IOUT) (VOUT= 0.0 V to VCC) 25 mA Continuous current through VCCor GND . 50 mA Maximum power dissipation at TA= +55C (in still air) (PD ) 500 mW Storage temperature range (TSTG) . -65C to +150C Lead temperature
14、 (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC). See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. 2/ 3/ 5/ Supply voltage range (VCC) +2.0 V dc to +5.5 V dc Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT) +0.0 V dc
15、to VCCMinimum high level input voltage (VIH): VCC = 2.0 V. +1.5 V VCC = 3.0 V. +2.1 V VCC = 5.0 V 0.5 V +3.85 V Maximum low level input voltage (VIL): VCC = 2.0 V. +0.5 V VCC = 3.0 V. +0.9 V VCC = 5.0 V 0.5 V +1.65 V Maximum high level output current (IOH): VCC = 2.0 V. -50 A VCC = 3.3 V 0.3 V -4 mA
16、 VCC = 5.0 V 0.5 V -8 mA Maximum low level output current (IOL): VCC = 2.0 V. +50 A VCC = 3.3 V 0.3 V +4 mA VCC = 5.0 V 0.5 V +8 mA Maximum input rise or fall rate (t/V): VCC = 3.3 V 0.3 V 100 ns/V VCC = 5.0 V 0.5 V 20 ns/V Case operating temperature range (TC) -55C to +125C 1/ Stresses above the ab
17、solute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits of the parameters specified herein shall apply over the full specified
18、 VCCrange and case temperature range of -55C to +125C. Unused inputs must be held high or low 4/ The input and output voltage ratings may be exceeded provided that the input and output current ratings are observed. 5/ Unused inputs must be held high or low to prevent them from floating. Provided by
19、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-96825 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standa
20、rds, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrat
21、ed Circuits Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDB
22、K-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict betwee
23、n the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements
24、for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLASMD596296825REVA2009MICROCIRCUITDIGITALADVANCEDHIGHSPEEDCMOSQUADRUPLE2INPUTPOSITIVEORGATEMONOLITHICSILICONPDF

链接地址:http://www.mydoc123.com/p-701113.html