DLA SMD-5962-94692 REV C-2007 MICROCIRCUIT LINEAR RAIL-TO-RAIL DUAL QUAD OPERATIONAL AMPLIFIER MONOLITHIC SILICON《杆对杆双重或四运算(操作)放大器硅单片电路线型微电路》.pdf

《DLA SMD-5962-94692 REV C-2007 MICROCIRCUIT LINEAR RAIL-TO-RAIL DUAL QUAD OPERATIONAL AMPLIFIER MONOLITHIC SILICON《杆对杆双重或四运算(操作)放大器硅单片电路线型微电路》.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-94692 REV C-2007 MICROCIRCUIT LINEAR RAIL-TO-RAIL DUAL QUAD OPERATIONAL AMPLIFIER MONOLITHIC SILICON《杆对杆双重或四运算(操作)放大器硅单片电路线型微电路》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device types 03 and 04. Technical and editorial changes throughout. 96-02-02 M. A. FRYE B Change to the max value of input offset current and the input bias current in table I. Update boilerplate. rrp 01-02-01 R. MONNIN C Drawing updated as p

2、art of 5 year review. -rrp 07-01-16 J. RODENBECK REV SHET REV SHET REV STATUS REV C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY RICK C. OFFICER DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY RAJESH R. PITHADIA COLUMBUS, OHIO 43218-3990 http:/w

3、ww.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, RAIL-TO-RAIL, DUAL/QUAD OPERATIONAL AMPLIFIER, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-06-02 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE

4、 67268 5962-94692 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E247-06 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94692 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC

5、FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number

6、 (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 94692 01 Q C X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (s

7、ee 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specif

8、ied RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 TLC2262 Rail-to-rail, dual, operational amplifier 02 TLC2264 Rai

9、l-to-rail, quad, operational amplifier 03 TLC2262A Rail-to-rail, dual, operational amplifier with enhanced VIO04 TLC2264A Rail-to-rail, quad, operational amplifier with enhanced VIO1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level a

10、s follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The cas

11、e outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N20 20 Squar

12、e leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE

13、 A 5962-94692 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (VDD) -0.5 V dc to +16.0 V dc 2/ Differential input voltage (VID) -16.0 V to +16.0 V 3/ Input voltage range (VIN) -VDD- 0.3 V to

14、 +VDD2/ Input current, each input (IIN) . +5.0 mA to -5.0 mA Output current (IOUT) +50.0 mA to -50.0 mA Total current into +VDD. +50.0 mA to -50.0 mA Total current out of -VDD+50.0 mA to -50.0 mA Duration of short-circuit current at or below +25C Unlimited 4/ Operating free-air temperature range (TA

15、) . -55C to +125C Storage temperature range (TSTG) . -65C to +150C Lead temperature (soldering 10 seconds) . +260C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Maximum junction temperature (TJ) . +150C Maximum power dissipation (PD): 5/ Cases C and 2 1375 mW Cases D and H . 700 mW Ca

16、se P 1050 mW 1.4 Recommended operating conditions. Supply voltage (VDD) 2.2 V dc to 8.0 V dc Input voltage range (VIN) -VDDto +VDD- 1.5 V Common-mode input voltage (VIC) -VDDto +VDD- 1.5 V Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, st

17、andards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Int

18、egrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. M

19、IL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the a

20、bsolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ All voltage values, except differential voltages, are with respect to the midpoint between +VDDand -VDD. 3/ Differential voltages are at the no

21、ninverting input with respect to the inverting input. Excessive current flows if the input is brought below -VDD- 0.3 V. 4/ The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded. 5/ Above TA= +25C,

22、 derate by the following factors; cases C and 2 at 11.0 mW/C, cases D and H at 5.5 mW/C, and case P at 8.4 mW/C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94692 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS,

23、OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulation

24、s unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modificat

25、ion in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions.

26、The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The

27、terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over

28、 the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In a

29、ddition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked.

30、Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535.

31、 The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6

32、.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this d

33、rawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device clas

34、ses Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devic

35、es acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore d

36、ocumentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or n

37、etworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94692 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherw

38、ise specified Group A subgroups Device type Limits 1/ Unit Min Max01, 02 2500 1 03, 04 950 01, 02 3000 VDD= 2.5 V, VIC= 0 V, RS= 50 , VOUT= 0 V 2, 3 03, 04 1500 01, 02 2500 1 03, 04 950 01, 02 3000 Input offset voltage VIOVDD= 5 V, VIC= 0 V, RS= 50 , VOUT= 0 V 2, 3 03, 04 1500 V VDD= 2.5 V, VIC= 0 V

39、, RS= 50 , VOUT= 0 V, TA= +125C 800 Input offset current IIOVDD= 5 V, VIC= 0 V, RS= 50 , VOUT= 0 V, TA= +125C 2 All 800 pA VDD= 2.5 V, VIC= 0 V, RS= 50 , VOUT= 0 V, TA= +125C 800 Input bias current IIBVDD= 5 V, VIC= 0 V, RS= 50 , VOUT= 0 V, TA= +125C 2 All 800 pA 1 0 to 4 VDD= 5 V, |VIO| 5 mV, RS= 5

40、0 2, 3 0 to 3.5 1 - 5 to 4 Common-mode input voltage range VICRVDD= 5 V, |VIO| 5 mV, RS= 50 2, 3 All -5 to 3.5 V 1 4.85 VDD= 5 V, VIC= 2.5 V, IOH= -100 A 2, 3 4.82 1 4.7 High-level output voltage VOHVDD= 5 V, VIC= 2.5 V, IOH= -200 A 2, 3 All 4.5 V VDD= 5 V, VIC= 2.5 V, IOL= 500 A 1, 2, 3 0.15 1 1.0

41、Low-level output voltage VOLVDD= 5 V, VIC= 2.5 V, IOL= 4 mA 2, 3 All 1.2 V 1 4.85 VDD= 5 V, VIC= 0 V, IOUT= -100 A 2, 3 4.82 1 4.7 Maximum positive peak output voltage swing +VOMVDD= 5 V, VIC= 0 V, IOUT= -200 A 2, 3 All 4.5 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproductio

42、n or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94692 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +12

43、5C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxVDD= 5 V, VIC= 0 V, IOUT= 500 A 1, 2, 3 -4.85 1 -4.0 Maximum negative peak output voltage swing -VOMVDD= 5 V, VIC= 0 V, IOUT= 4 mA 2, 3 All -3.8 V 1 80 VDD= 5 V, VIC= 2.5 V, VOUT= 1 V to 4 V, RL= 100 k 2/ 2, 3 50 1 80

44、Large-signal differential voltage amplification AVDVDD= 5 V, VIC= 0 V, VOUT= 4 V, RL= 100 k 2/ 2, 3 All 50 V/mV VDD= 5 V, VOUT= 2.5 V, VIC= 0 V to 2.7 V, RS= 50 70 Common-mode rejection ratio CMRR VDD= 5 V, VOUT= 0 V, VIC= -5 V to 2.7 V, RS= 50 1, 2, 3 All 75 dB Supply voltage rejection ratio (VDD/V

45、IO) kSVRVDD= 2.2 V to 8 V, VIC= VDD/2, no load 1, 2, 3 All 80 dB 01, 03 500 VDD= 5 V, VOUT= 2.5 V, no load 02, 04 1000 01, 03 500 Supply current (both channels) IDDVDD= 5 V, VOUT= 0 V, no load 1, 2, 3 02, 04 1000 A 4 0.35 VDD= 5 V, RL= 50 k, 2/ VOUT= 1 V to 3 V, CL= 100 pF 5, 6 0.25 4 0.35 Slew rate

46、 at unity gain SR VDD= 5 V, RL= 50 k, 2/ VOUT= 1.9 V, CL= 100 pF 5, 6 All 0.25 V/s 1/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device termi

47、nal. 2/ Referenced to 2.5 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94692 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Device types 01, 03 0

48、2, 04 Case outlines H P 2 C and D 2 Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 NC OUTPUT 1 -INPUT 1 +INPUT 1 -VDD+INPUT 2 -INPUT 2 OUTPUT 2 +VDDNC - - - - - - - - - - OUTPUT 1 -INPUT 1 +INPUT 1 -VDD+INPUT 2 -INPUT 2 OUTPUT 2 +VDD- - - - - - - - - - - - NC OUTPUT 1 NC NC -INPUT 1 NC +INPUT 1 NC NC -VDDNC +INPUT 2 NC NC -INPUT 2 NC O