DLA SMD-5962-94646 REV A-2009 MICROCIRCUIT LINEAR DIGITAL TO SYNCHRO RESOLVER CONVERTER MICROPROCESSOR COMPATIBLE 16-BIT HYBRID.pdf

《DLA SMD-5962-94646 REV A-2009 MICROCIRCUIT LINEAR DIGITAL TO SYNCHRO RESOLVER CONVERTER MICROPROCESSOR COMPATIBLE 16-BIT HYBRID.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-94646 REV A-2009 MICROCIRCUIT LINEAR DIGITAL TO SYNCHRO RESOLVER CONVERTER MICROPROCESSOR COMPATIBLE 16-BIT HYBRID.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing per 5 year review. -sld 09-01-13 Robert M. Heber REV SHET REV SHET REV STATUS REV A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Gary Zahn CHECKED BY Michael C. Jones DEFENSE SUPPLY CEN

2、TER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil/ APPROVED BY Kendall A. Cottongim STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-07-08 MICROCIRCUIT, LINEAR, DIGITAL TO SYNCHRO/RESOLVE

3、R CONVERTER, MICROPROCESSOR COMPATIBLE, 16-BIT, HYBRID AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-94646 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E485-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5

4、962-94646 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available

5、 and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 94646 01 H X X Federal stock class designator RHA designator (see 1.2.1) Devicetyp

6、e (see 1.2.2)Deviceclass designatorCaseoutline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash

7、(-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function Accuracy 01 HDSR2006-34V/S/2 Digital-to-synchro/resolver converter 1 arc min synchro mode 2 arc min resolver mode 02 HDSR2006-34V/R/2 Digital

8、-to-synchro/resolver converter 1 arc min resolver mode 2 arc min synchro mode 03 HDSR2006-34H/2 Digital-to-synchro/resolver converter 2 arc min both modes 04 HDSR2006-34S/2 Digital-to-synchro/resolver converter 4 arc min both modes 05 HDSR2056-34V/S/2 Digital-to-synchro/resolver converter 1 arc min

9、synchro mode 2 arc min resolver mode 06 HDSR2056-34V/R/2 Digital-to-synchro/resolver converter 1 arc min resolver mode 2 arc min synchro mode 07 HDSR2056-34H/2 Digital-to-synchro/resolver converter 2 arc min both modes 08 HDSR2056-34S/2 Digital-to-synchro/resolver converter 4 arc min both modes 1.2.

10、3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product

11、 assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability device

12、s are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conforma

13、nce inspections (Group A, B, C and D). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94646 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 E Designate

14、s devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will no

15、t adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: O

16、utline letter Descriptive designator Terminals Package style X See figure 1 36 Dual-in-line 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Power supplies: +VS. +18 V dc -VS-18 V dc Logic input voltage range -0.3 V dc to +6.5 V dc Reference

17、 input voltage. Twice the pin programmed voltage Power dissipation (PD) . 1 W Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) +170C 1.4 Recommended operating conditions. Power supplies voltage range: +VS. +13.5 V dc to +16.5 V dc -VS-1

18、3.5 V dc to -16.5 V dc Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified,

19、the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for

20、 Electronic Component Case Outlines. _ 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

21、e from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94646 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings.

22、 (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the refe

23、rences cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G,

24、 H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or o

25、ptimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design,

26、 construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be

27、 as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test

28、requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufactu

29、rers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, f

30、or each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA)

31、 upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL

32、-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL

33、-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT

34、 DRAWING SIZE A 5962-94646 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA+125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max Reso

35、lution RES MSB = 180 and LSB = .0055 7, 8 All 16 Bits 01, 02, 05, 06 -1 2/ +1 2/ 03, 07 -2 3/ +2 3/ Accuracy AOUTMeasured at angles of 0, 10, 20, 30,4050, 60, 90, 120, 135, 150, 180, 210, 225, 240, 270, 300, 315, and 330 4, 5, 6 04, 08 -4 3/ +4 3/ Arc min REFERENCE INPUTS Reference voltage 4/ (pin p

36、rogrammable) VINInput between RH and RL, Input between RH and RL, Input between RH and RL with RH and RL grounded, see figure 3 4, 5, 6 All 1.17 23.47 103.5 1.43 28.6 126.5 V rms Frequency 4/ dc to 1000 Hz 4, 5, 6 All 1000 Hz RH and RL, differential 198 202 RH and RL single ended 99 101 RH and RL, d

37、ifferential 9.9 10.1 Input impedance 4/ ZIN RH and RL, single ended 4, 5, 6 All 4.95 5.05 k DIGITAL INPUT 5/ Input low voltage VIL Logic “0“ -0.3 +0.8 Input high voltage VIHLogic “1“ 1, 2, 3 All 2.4 5.5 V ANALOG OUTPUTS (resolver or synchro mode) Output voltage (Sin, Cos) VOUT 6.742 6.878 Output vol

38、tage (S1, S2, S3) VOUT Measured between any two of three pins 4, 5, 6 All 11.682 11.918 V rms +VS= +16.5 V dc Output current, each output IOUT -VS= -16.5 V dc 4, 5, 6 All 2 mA DC offset VOS 1, 2, 3 All -50 +50 mV REGISTER CONTROLS (functional testing) Data inputs B1 through B8 enter the buffer regis

39、ter Logic “1“ Enables HI byte HBE Buffer register in the hold mode 7 All Logic “0“ Data inputs B9 through B16 enter the buffer register Logic “1“ Enables LO byte LBE Buffer register in the hold mode 7 All Logic “0“ Transfers contents of the buffer register to the holding register Logic “1“ Transfer

40、data logic LDC Converter in the hold mode 7 All Logic “0“ See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94646 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION

41、 LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA+125C Group A subgroups Device type Limits Unit unless otherwise specified Min Max REGISTER CONTROLS (functional testing) - continued Normal operation Logic “1“ 0 test

42、 angle STO Presets 0 angle to holding register 7 01, 02, 03, 04 Logic “0“ 6/ Normal operation Logic “1“ 90 test angle 90ST Presets 90 angle to holding register 7 01, 02, 03, 04 Logic “0“ 7/ POWER SUPPLIES Supply currents ISQ VS= 16.5 V dc, no load 1, 2, 3 All 30 mA 1/ Unless otherwise specified; +VS

43、= +15 V dc and -VS= -15 V dc. 2/ Accuracy is measured and recorded in the highest accuracy mode at 400 Hz 10 carrier frequency. The alternate mode is tested on a go-no-go basis at angle 90, 180, 225, 270, and 315. 3/ Accuracy is measured and recorded at 400 Hz 10carrier frequency in the synchro mode

44、; resolver mode is tested on a go-no-go basis. 4/ Parameter shall be tested as part of device initial characterization and after design and process changes. Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. 5/ Logic “0“ low limit of -0.3 V dc and

45、logic “1“ high of +VSare not tested and are guaranteed by design. 6/ Assumes 90ST = logic “1“. 7/ Assumes STO = logic “0“. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94646 DEFENSE SUPPLY CENTER COLUMBUS

46、COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 Inches mm Inches mm .005 0.13 .100 2.54 .010 0.25 .180 4.57 .018 0.46 .250 6.35 .030 0.76 .600 15.24 .055 1.40 .775 19.69 .086 2.18 1.700 43.18 .090 2.29 1.895 48.13 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are

47、 given for information only. 3. Lead spacing dimensions apply only at seating plane. 4. Case is electrically floating. 5. Standoffs are ceramic or glass (3 each). FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC

48、IRCUIT DRAWING SIZE A 5962-94646 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 Device types 01 - 08 Case outline X Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 S1 S2 (Cos) S3 (Sin) S3 S2 R RL RL RH RH STO 90ST +VS -VS TP1 LDC LBE Ground B16 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 HBE VLNote: For device types