DLA SMD-5962-90563 REV B-2006 MICROCIRCUIT DIGITAL BIPOLAR ADVANCED SCHOTTKY TTL OCTAL BUFFER AND LINE DRIVER WITH OPEN-COLLECTOR OUTPUTS MONOLITHIC SILICON《硅单片 装有集电极开路输出八位缓冲器 驱动器 .pdf

《DLA SMD-5962-90563 REV B-2006 MICROCIRCUIT DIGITAL BIPOLAR ADVANCED SCHOTTKY TTL OCTAL BUFFER AND LINE DRIVER WITH OPEN-COLLECTOR OUTPUTS MONOLITHIC SILICON《硅单片 装有集电极开路输出八位缓冲器 驱动器 .pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-90563 REV B-2006 MICROCIRCUIT DIGITAL BIPOLAR ADVANCED SCHOTTKY TTL OCTAL BUFFER AND LINE DRIVER WITH OPEN-COLLECTOR OUTPUTS MONOLITHIC SILICON《硅单片 装有集电极开路输出八位缓冲器 驱动器 .pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R176-92. 92-04-14 Monica L. Poelking B Redrawn with changes. Update to current requirements. Editorial changes throughout. - gap 06-07-10 Raymond Monnin The original first page of this drawing has been replaced

2、. REV SHET REV SHET REV STATUS REV B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Meredith Ward DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Tim H. Noh COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPAR

3、TMENTS APPROVED BY William K. Heckman MICROCIRCUIT, DIGITAL, BIPOLAR, ADVANCED SCHOTTKY, TTL, OCTAL BUFFER AND LINE AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 90-08-31 DRIVER WITH OPEN-COLLECTOR OUTPUTS, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-90

4、563 SHEET 1 OF 9 DSCC FORM 2233 APR 97 5962-E330-06 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90563 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 9

5、7 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-90563 01 R X Drawing number

6、Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AS756 Octal buffer and line driver with open-collector outputs 1.2.2 Case outline(s). The case out

7、line(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 dual-in-line S GDFP2-F20 or CDFP3-F20 20 flat 2 CQCC1-N20 20 square chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, ap

8、pendix A. 1.3 Absolute maximum ratings. Supply voltage range . -0.5 V dc minimum to +7.0 V dc maximum Input voltage range -1.2 V dc at -18 mA to +7.0 V dc Maximum power dissipation (PD) . 517 mW Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Thermal resistan

9、ce, junction-to-case (JC): . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Supply voltage (VCC) . +4.5 V dc minimum to +5.5 V dc maximum Minimum high level input voltage (VIH) . 2.0 V dc Maximum low level input voltage (VIL) . 0.7 V dc High level output volta

10、ge (VOH) 5.5 V Case operating temperature range (TC) -55C to +125C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90563 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC

11、FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicita

12、tion or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF D

13、EFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil;quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue,

14、 Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific

15、 exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (Q

16、ML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as d

17、ocumented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-3

18、8535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.

19、2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Test circuit and switching waveforms. The test circuit and switching waveforms shall be as specified on figure 3. 3.3 Electr

20、ical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specif

21、ied in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90563 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL

22、B SHEET 4 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due t

23、o space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with

24、a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). Th

25、e certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in M

26、IL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity re

27、tain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,

28、 appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. T

29、he test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the inte

30、nt specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo

31、 reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90563 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C T

32、C +125C Group A subgroups Limits Unit unless otherwise specified Min Max High level output current IOHVCC= 4.5 V, VOH= 5.5 V 1, 2, 3 0.1 mA Low level output voltage VOLVCC= 4.5 V, IOL= 48 mA 2/ 1, 2, 3 0.55 V IL= 0.7 V IN= 2.0 V Input clamp voltage VICVCC= 4.5 V, IIN= -18 mA 1, 2, 3 -1.2 V Low level

33、 input current IILVCC= 5.5 V, 1, 2, 3 -0.5 mA VIN= 0.4 V High level input current IIHVCC= 5.5 V, VIN= 2.7 V 1, 2, 3 20 A Supply current ICCHVCC= 5.5 V 1, 2, 3 15 mA ICCLVCC= 5.5 V 1, 2, 3 80 mA Functional tests See 4.3.1c 3/ 7, 8 Propagation delay time, tPLH14.5 V to 5.5 V dc 9, 10, 11 3 20 ns input

34、 An to output Yn CL= 50 pF tPHL1RL= 500 4/ 1 7 Propagation delay time, tPLH29, 10, 11 3 22 ns input G to output Yn tPHL21 8.5 1/ Unused inputs that do not directly control the pin under test shall be 2.5 V or 0.4 V, and shall not exceed 5.5 V or go less than 0.0 V. No inputs shall be floating. 2/ Al

35、l outputs shall be tested. In the case where only one input at VILmaximum or VIHminimum produces the proper output state, the test shall be performed with each input being selected as VILmaximum or VIHminimum input. 3/ Functional tests shall be conducted at input test conditions of GND VIL VOLand VO

36、H VIH VCC. 4/ Propagation delay times are based on single output switching. Unused outputs = 3.5 V or 0.3 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90563 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO

37、 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 Case outlines R, S, and 2 Terminal number Terminal symbol 1 1 G 2 1A1 3 2Y4 4 1A2 5 2Y3 6 1A3 7 2Y2 8 1A4 9 2Y1 10 GND 11 2A1 12 1Y4 13 2A2 14 1Y3 15 2A3 16 1Y2 17 2A4 18 1Y1 19 2 G 20 VCCFIGURE 1. Terminal connections. An G Yn X H Disabled

38、L L H H L L H = High voltage level L = Low voltage level X = Irrelevant FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90563 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 RE

39、VISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 NOTES: 1. CLincludes scope and jig capacitance. 2. All input pulses have the following characteristics: PRR 10 MHz, duty cycle = 50 percent, tr= tf= 3 ns 1 ns. 3. The outputs are measured one at a time with one input transition per measurement. FIGURE 3.

40、Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90563 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE II. El

41、ectrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) - - - Final electrical test parameters (method 5004) 1*, 2, 3, 7, 8, 9, 10, 11 Group A test requirements (method 5005) 1, 2, 3, 7, 8,

42、 9, 10, 11 Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. 4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional

43、 criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, and 6 in table I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroups 7 and 8 shall include verification of the truth table. 4.3.2 Groups C and D inspections. a. End-point ele

44、ctrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing

45、 or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of

46、MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90563 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 5. PACKAGING 5.1 Packaging requiremen

47、ts. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceab

48、ility. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared specification or drawing. 6.3 Configuration control of SMDs. All proposed changes to existing SMDs will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal. 6.4 Record of users. Military and industrial users shall inform Defense Supply Cente