DLA SMD-5962-89639 REV A-2010 MICROCIRCUIT LINEAR 4-CHANNEL MULTIPLEXER AMPLIFIER MONOLITHIC SILICON.pdf

《DLA SMD-5962-89639 REV A-2010 MICROCIRCUIT LINEAR 4-CHANNEL MULTIPLEXER AMPLIFIER MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-89639 REV A-2010 MICROCIRCUIT LINEAR 4-CHANNEL MULTIPLEXER AMPLIFIER MONOLITHIC SILICON.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 10-02-18 C. SAFFLE THE FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12

2、13 PMIC N/A PREPARED BY JOSEPH A. KERBY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRY

3、E MICROCIRCUIT, LINEAR, 4-CHANNEL, MULTIPLEXER AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 91-02-07 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-89639 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E187-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

4、e from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in acco

5、rdance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-89639 01 V A Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circuit fun

6、ction as follows: Device type Generic number Circuit function 01 LM604 4-channel multiplexer amplifier 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style V GDIP1-T18 or CDIP2-T18 18 Dual-in-line 1

7、.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage (VS) . 36 V dc or 18 V dc Differential input voltage . 18 V dc Input voltage range . 18 V dc Output short circuit to GND . Continuous 1/ Storage temperature range . -65C to +1

8、50C Lead temperature (soldering, 5 seconds) +300C Junction temperature (TJ) . +150C Power dissipation (PD) 1.6 W 2/ 3/ Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) 75C/W 1.4 Recommended operating conditions. Supply voltage (VS) . 15 V dc A

9、mbient operating temperature range (TA) . -55C to +125C _ 1/ Applied to both single and split supply operation. Continuous short circuit operation can result in exceeding the maximum allowed junction temperature. 2/ When operating at TA 25C, the maximum power dissipation must be derated based on JA.

10、 3/ Must withstand the added PDdue to short circuit test; e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSC

11、C FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solici

12、tation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF

13、 DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philad

14、elphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been

15、obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qu

16、alified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Qua

17、lity Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to

18、identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein. 3.2.2 Terminal

19、 connections. The terminal connections shall be as specified on figure 1. 3.2.3 Block diagram and truth table. The block diagram and truth table shall be as specified on figure 2. 3.2.4 Channel switching waveforms. The channel switching waveforms shall be as specified on figure 3. 3.2.5 Output disab

20、le and enable waveforms. The output disable and enable waveforms shall be as specified on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating te

21、mperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDAR

22、D MICROCIRCUIT DRAWING SIZE A 5962-89639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA+125C VS= 15 V Group A subgroupsDevice type Limits Unit VOUT= 0 V, VCM= 0 V

23、unless otherwise specified Min Max Input offset voltage VIORS= 10 k 1 01 -1 +1 mV 2,3 -3 +3+V = +5 V, -V = 0 V, 1 -1 +1 VOUT= 2 V, RS= 10 k 2,3 -3 +3 Input offset current IIO1 01 -10 +10 nA 2,3 -12 +12 +V = +5 V, -V = 0 V, 1 -10 +10 VOUT= 2 V 2,3 -18 +18 Input bias current IIB1 01 -50 +50 nA 2,3 -60

24、 +60 +V = +5 V, -V = 0 V, 1 -80 +80 VOUT= 2 V 2,3 -110 +110 Input common mode voltage range +VCM1 01 13.5 V 2,3 13.0 -VCM1,2,3 -15Positive output voltage swing high +VOPRL= 10 k 1 01 13 V 2,3 12.5 +V = +5 V, -V = 0 V, 1 3.2 RL= 10 k 2,3 3.0 RL= 600 1 12.3 2,3 10+V = +5 V, -V = 0 V, 1 3.0 RL= 600 2,3

25、 2.8 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Elect

26、rical performance characteristics Continued. Test Symbol Conditions -55C TA+125C VS= 15 V Group A subgroupsDevice type Limits Unit VOUT= 0 V, VCM= 0 V unless otherwise specified Min Max Negative output voltage swing low -VOPRL= 10 k 1 01 -13.8 V 2,3 -13.3 +V = +5 V, -V = 0 V, 1 0.7 RL= 10 k 2,3 0.8

27、RL= 600 1 -12.2 2,3 -11.7+V = +5 V, -V = 0 V, 1 0.6 RL= 600 2,3 0.7 Large signal voltage gain AVVOUT= 0 to 10 V, RL= 2 k 4 01 50 V/mV VOUT= 0 to -10 V, RL= 2 k VOUT= 0 to 10 V, RL= 600 VOUT= 0 to -10 V, RL= 600 VOUT= 0 to 10 V, RL= 2 k 5,6 25 VOUT= 0 to -10 V, RL= 2 k VOUT= 0 to 10 V, RL= 600 VOUT=

28、0 to -10 V, RL= 600 Common mode rejection ratio CMRR VCM= -15 V to +13.5 V 4 01 80 dB 5,6 70 +V = +5 V, -V = 0 V, 4 80 VOUT= 2 V, VCM= 0 V to 3.5 V 5,6 70 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCI

29、RCUIT DRAWING SIZE A 5962-89639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA+125C VS= 15 V Group A subgroupsDevice type Limits Unit VOUT= 0 V, VCM= 0 V

30、 unless otherwise specified Min Max Power supply rejection ratio PSRR VS= 5.0 V to 16.0 V 4 01 80 dB 5,6 70 +V = +4.0 V to +5.0 V, 4 80 -V = 0 V 5,6 70 Output short circuit current IOS1 01 -50 +50 mA 2,3 -60 +60 Output leakage current IOBi-state output disabled, 1 01 -10 +10 A VOUT= 13 V, VOUT= 0 V,

31、 VOUT= -13.5 V 2,3 -20 +20 Supply current IS1 01 9 mA 2,3 10 Digital input threshold 1/ 2/ voltage VIH, 1 01 1.0 1.8 V VIL2,3 0.8 2.0Digital input current 1/ 2/ high IIH1 01 5 A 2,3 10 Digital input current 1/ 2/ low IIL1 01 5 A 2,3 10 Negative slew rate -SR RL= 2 k, AV= 1 4 01 2.0 V/s 5,6 1.5Positi

32、ve slew rate +SR RL= 2 k, AV= 1 4 01 2.0 V/s 5,6 1.5See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL

33、 A SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA+125C VS= 15 V Group A subgroupsDevice type Limits Unit VOUT= 0 V, VCM= 0 V unless otherwise specified Min Max Gain bandwidth product GBW f = 100 kHz 4 01 6 MHz 5,6 3 Channel swi

34、tching time tSW1Channel 2 to channel 1 Channel 1 to channel 2 9 01 5.5 s Channel 4 to channel 3 Channel 3 to channel 4, see figure 3 10,11 6.5 Multiplexer amplifier enable time tEN1See figure 4 9 01 4.0 s 10,11 5.0 Multiplexer amplifier disable time tDISSee figure 4 9 01 2.0 s 10,11 3.0 1/ Digital i

35、nput tests are for A, B, EN , WR , and CS pins. 2/ Input voltage levels are with respect to digital ground (pin 4) which must be at least 4.0 V below +V. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In additio

36、n, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on

37、all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall

38、be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38

39、535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be requir

40、ed for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer.

41、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outline V Terminal number Term

42、inal symbol 1 A 2 B 3 OPEN PIN 4 DIGITAL GROUND 5 +V 6 CHANNEL -1 7 CHANNEL +1 8 CHANNEL -2 9 CHANNEL +2 10 CHANNEL +3 11 CHANNEL -3 12 CHANNEL +4 13 CHANNEL -4 14 VOUT15 -V 16 CS 17 WR 18 EN FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without

43、 license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89639 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 Channel selection A B WR CS Channel 0 0 0 0 1 0 1 0 0 2 1 0 0 0 3 1 1 0 0 4 X X X 1 Unchanged X X 1 X Unchanged Bi-state outpu

44、t control EN WR CS Output state 0 0 0 Enabled 1 0 0 Disabled, high ZX X 1 Unchanged X 1 X Unchanged FIGURE 2. Block diagram and truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89639 DEFENSE SUPPL

45、Y CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 10 DSCC FORM 2234 APR 97 FIGURE 3. Channel switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89639 DEFENSE SUPPLY CENTER C

46、OLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 11 DSCC FORM 2234 APR 97 FIGURE 4. Output disable and output enable waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89639 DEFENSE SUPPLY CEN

47、TER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 12 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-88

48、3, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circu