DLA MS35436 REV C-2003 TERMINAL LUG SOLDER TYPE COPPER STAMPING INSULATION GRIP ONE HOLE《焊料型1孔绝缘手柄铜冲压片接线端接线片》.pdf

《DLA MS35436 REV C-2003 TERMINAL LUG SOLDER TYPE COPPER STAMPING INSULATION GRIP ONE HOLE《焊料型1孔绝缘手柄铜冲压片接线端接线片》.pdf》由会员分享，可在线阅读，更多相关《DLA MS35436 REV C-2003 TERMINAL LUG SOLDER TYPE COPPER STAMPING INSULATION GRIP ONE HOLE《焊料型1孔绝缘手柄铜冲压片接线端接线片》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5940 INCH-POUND MS35436C 15 December 2003 SUPERSEDING MS35436B 10 February 1961 DETAIL SPECIFICATION SHEET TERMINAL, LUG, SOLDER TYPE, COPPER STAMPING, INSULATION GRIP, ONE HOLE Inactive for new design after 15 December 2003 This specification sheet is approved for use by all departmen

2、ts and agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the issue of MIL-DTL-15659 listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicit

3、ation. DCAFEBHBBOptional body and grip designs. FIGURE 1. Terminal dimensions for -1 through -29. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35436C 2 TABLE I. Dash numbers and dimensions for -1 through -29. A Dash no. Wire size AWG1nominal Stu

4、d size Min. Max. B C D E F H 0.003 1 1/4 0.258 0.285 2 18-20 5/16 0.320 0.347 1/8 15/32 55/64 15/64 35/64 3 4 0.115 0.127 9/32 57/64 25/64 4 6 0.141 0.153 5 8 0.167 0.179 6 10 0.193 0.205 11/32 63/64 31/64 7 1/4 0.258 0.285 9/16 1 5/32 21/32 8 5/16 0.320 0.347 9 14-16 3/8 0.383 0.410 3/16 11/16 1 3/

5、8 5/16 27/32 0.032 10 8 0.167 0.179 11 10 0.193 0.205 11/32 63/64 31/64 12 1/4 0.258 0.285 9/16 1 5/32 21/32 13 5/16 0.320 0.347 1 11/32 25/32 14 3/8 0.383 0.410 3/8 27/32 15 7/16 0.448 0.475 11/16 1 15/32 31/32 16 10-12 1/2 0.510 0.537 1/4 13/16 1 9/16 25/64 1 1/32 0.040 17 10 0.193 0.205 19/32 18

6、1/4 0.258 0.285 9/16 1 13/32 21/32 19 5/16 0.320 0.347 11/16 1 17/32 25/32 20 3/8 0.383 0.410 5/8 29/32 21 8 7/16 0.448 0.475 5/16 13/16 1 23/32 29/64 1 1/32 22 10 0.193 0.205 1 11/32 21/32 23 1/4 0.258 0.285 13/32 23/32 24 5/16 0.320 0.347 9/16 1 15/32 25/32 25 3/8 0.383 0.410 1 5/8 29/32 26 7/16 0

7、.448 0.475 13/16 1 23/32 1 1/32 27 4-6 1/2 0.510 0.537 3/8 15/16 1 13/16 9/16 1 3/32 0.045 28 3/8 0.383 0.410 - 29 0-1 1/2 0.510 0.537 7/16 15/16 2 15/32 45/64 - 0.102 1American Wire Gauge. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35436C 3 F

8、BHEDCATABLE II. Dash numbers and dimensions for -30 through -43. A Dash no. Wire size AWG1nominal Stud size Min. Max. B C D E F H 30 10 1/8 9/32 21/32 7/32 21/64 0.032 31 6 0.141 0.153 32 8 0.167 0.179 33 10 0.193 0.205 11/32 1 34 8 3/8 0.383 0.410 5/32 11/16 1 7/32 9/32 15/32 0.025 35 6 0.141 0.153

9、 36 8 0.167 0.179 37 10 0.193 0.205 38 6 1/4 0.258 0.285 3/16 1/2 1 3/32 1/4 19/32 0.032 39 6 0.141 0.153 40 8 0.167 0.179 41 10 0.193 0.205 42 12 0.221 0.236 43 4 1/4 0.258 0.285 7/32 1/2 1 3/32 11/32 19/32 0.040 1American Wire Gauge. Optional body and grip design. FIGURE 2. Terminal dimensions for

10、 -30 through -43. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35436C 4 C11618R18R532A (Dia)BDGFEFIGURE 3. Terminal dimensions for -44. TABLE III. Dash numbers and dimensions for -44. A Dash no. Wire size AWG1nominal Stud size Min. Max. B C D E

11、F 0.003 G 44 12 6 0.141 0.153 3/32 11/16 9/32 11/32 0.030 5/64 1American Wire Gauge. REQUIREMENTS: 1. Material: Electrolytic copper strip or sheet alloy C11000, temper O60 in accordance with ASTM B 152/B 152M (DoD adopted). 2. Finish: Tinned; electrodeposited over entire surface in accordance with A

12、STM B 545 (DoD adopted). Minimum thickness 0.0005 inches all over. NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerance is 1/64. 3. Remove all burrs. 4. Referenced documents of issue in effect on date of invitation for bids shall apply. 5. In the event of a conflict between t

13、he text of this document and the references cited herein, the text of this document shall take precedence. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35436C 5 6. The part or identifying number (PIN) consists of the letters MS, the specificatio

14、n sheet number, and a dash number taken from table I, II, or III. MS 35436 - 3 CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing Activity: Army - CR Navy - SH Air Force -11 DLA - GS2 (Project 5940-1435) Review Activities: Army - MI Dash number Specification sheet number MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-