DLA MS35431 REV H-2003 TERMINAL LUG SOLDER TYPE COPPER STAMPING ONE HOLE FLAT [Use In Lieu Of DLA MS0035431 REV C]《焊料型平面1孔铜冲压片接线端接线片》.pdf

《DLA MS35431 REV H-2003 TERMINAL LUG SOLDER TYPE COPPER STAMPING ONE HOLE FLAT [Use In Lieu Of DLA MS0035431 REV C]《焊料型平面1孔铜冲压片接线端接线片》.pdf》由会员分享，可在线阅读，更多相关《DLA MS35431 REV H-2003 TERMINAL LUG SOLDER TYPE COPPER STAMPING ONE HOLE FLAT [Use In Lieu Of DLA MS0035431 REV C]《焊料型平面1孔铜冲压片接线端接线片》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A FSC 5940 INCH-POUND MS35431H 15 December 2003 SUPERSEDING MS35431G 16 February 1987 DETAIL SPECIFICATION SHEET TERMINAL, LUG, SOLDER TYPE, COPPER STAMPING, ONE HOLE, FLAT Inactive for new design after 27 October 1998. This specification sheet is approved for use by all departments and agen

2、cies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-15659. ED.018 .003CA B.094 RFIGURE 3. Optional body design. FIGURE 2. Terminal dimensions for -9 (See note 4). FIGURE 1. Terminal dimensions. Provided

3、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35431H 2 TABLE I. Dash numbers and dimensions. A Dash no. Wire size AWG1nominal Stud size Min. Max. B C D E 1 0.625 0.375 2 4 0.115 0.127 0.875 0.625 3 0.625 0.375 4 6 0.141 0.153 0.875 0.625 5 0.625 0.375 6 8

4、 0.167 0.179 0.875 0.625 7 0.625 0.375 8 10 0.193 0.205 0.312 0.875 0.625 9 12 0.250 0.253 0.265 0.094 0.375 0.812 0.531 10 10 0.130 11 16 0.312 0.313 0.322 0.062 0.469 0.875 0.500 12 0.046 0.187 0.328 0.187 13 0.072 0.234 0.500 14 0.250 0.516 0.312 15 12 2 0.090 0.096 0.094 0.312 0.625 0.375 1Ameri

5、can Wire Gauge. REQUIREMENTS: 1. Material: Electrolytic copper strip or sheet alloy C11000, temper O60 in accordance with ASTM B 152/B 152M (DoD adopted). 2. Finish: Tinned; electrodeposited over entire surface in accordance with ASTM B 545 (DoD adopted). Minimum thickness 0.0005 inches all over. NO

6、TES: 1. All dimensions are in inches. 2. Unless otherwise specified, tolerance is 0.015. 3. Remove all burrs. 4. Dash number 9 shall conform to the design shown in figure 2. 5. Referenced documents of issue in effect on date of invitation for bids shall apply. 6. In the event of a conflict between t

7、he text of this document and the references cited herein, the text of this document takes precedence. 7. Optional body design shown in Figure 3 for all dash numbers except 9. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35431H 3 7. The part or i

8、dentifying number (PIN) consists of the letters MS, the specification sheet number, and a dash number taken from table I. MS 35431 - 3 CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes

9、. Custodians: Preparing Activity: Army - AR Navy - AS Air Force - 11 DLA - GS2 (Project 5940-1446) Review Activities: Army - AV, MI Navy - MC Air Force - 99 Dash number Specification sheet number MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-