DLA MS27223 REV C-2007 NIPPLE ASSEMBLY 90 ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES 1 4 INCH THROUGH 2 INCH TUBE SIZES《通过1 4英寸至2英寸的石油管道可重复使用的90度螺纹接口液压法兰软管组件适配器》.pdf

《DLA MS27223 REV C-2007 NIPPLE ASSEMBLY 90 ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES 1 4 INCH THROUGH 2 INCH TUBE SIZES《通过1 4英寸至2英寸的石油管道可重复使用的90度螺纹接口液压法兰软管组件适配器》.pdf》由会员分享，可在线阅读，更多相关《DLA MS27223 REV C-2007 NIPPLE ASSEMBLY 90 ADAPTER HOSE TO TUBE REUSABLE HYDRAULIC FUEL AND OIL LINES 1 4 INCH THROUGH 2 INCH TUBE SIZES《通过1 4英寸至2英寸的石油管道可重复使用的90度螺纹接口液压法兰软管组件适配器》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUNDMS27223C 14 May 2007 SUPERSEDING MS27223B 22 September 2000 DETAIL SPECIFICATION SHEET NIPPLE ASSEMBLY 90, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES 1/4 INCH THROUGH 2 INCH TUBE SIZES This specification is approved for use by all Departments and Agencies of the Depart

2、ment of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. FIGURE 1. Nipple assembly dimensions and configuration. AMSC N/A Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

3、FSC4730 MS27223C 2 Dash number A .035 (0.89) inches (mm) B .035 (0.89) inches (mm) C inches (mm) D Wire MS27238 dash number E Shoulder MS27236 dash number F Nut SAE-AS4370 dash number G Nipple MS27239 dash number H Elbow MS27234 dash number K Rad (ref) inches (mm) -4 .626 (15.90) .718 (18.24) .37 (9

4、.40) -4 -4 -4 -4 -4 .38 (9.65) -5 .750 (19.05) .844 (21.44) -5 -5 -5 -5 -5 .44 (11.18) -6 .812 (20.62) .922 (23.42) .38 (9.65) -6 -6 -6 -6 -6 .50 (12.70) -8 .876 (22.25) .938 (23.83) .44 (11.18) -8 -8 -8 -8 -8 .50 (12.70) -10 1.000 (25.40) 1.126 (28.60) .50 (12.70) -10 -10 -10 -10 -10 .62 (15.75) -1

5、2 1.220 (30.99) 1.372 (34.85) .57 (14.48) -12 -12 -12 -12 -12 .84 (21.34) -16 1.344 (34.14) 1.502 (38.15) .63 (16.00) -16 -16 -16 -16 -16 .97 (24.64) -20 1.688 (42.88) 1.784 (45.31) .64 (16.26) -20 -20 -20 -20 -20 1.19 (30.23) -24 1.938 (49.23) 2.036 (51.71) .77 (19.56) -24 -24 -24 -24 -24 1.38 (35.

6、05) -32 2.376 (60.35) 2.532 (64.31) .92 (23.37) -32 -32 -32 -32 -32 1.75 (44.45) NOTES: 1. Dimensions are in inches 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are as follows: Angles 1; decimals .005 inch (0.13 mm). 4. Nut shall swivel freely after

7、 assembly. 5. Part or Identifying Number (PIN). FIGURE 1. Nipple assembly dimensions and configuration - Continued. REQUIREMENTS. Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between this dr

8、awing and MIL-DTL-5070, this drawing shall govern. Intended use. This part is a component of MS27224. Materials: Materials shall be in accordance with MIL-DTL-5070. Finish: Finish shall be in accordance with MIL-DTL-5070. Platings are applied after heat treats and before assembling nut. Color identi

9、fication: Color identification shall be in accordance with MIL-DTL-5070. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27223C 3 Braze: Steel: Braze at points J in accordance with AWS C3.4, AWS C3.5, AWS C3.6, or AWS C3.7. Aluminum: Braze at point

10、s J in accordance with SAE-AMS2672. Titanium: Braze at points J. Heat treatment: Steel: Heat treat in accordance with SAE-AMS-H-6875 after braze so that Rockwell hardness of nipple is C-25. Aluminum: Heat treat in accordance with SAE-AMS2770, condition T6, after braze. Titanium: Heat treatment in ac

11、cordance with SAE-AMS2801, temper STA900, after braze. PIN example: MS 27223 -4 CZ Material/finish code, see table I Dash number on figure 1 Specification number MS prefix TABLE I. Code for material and finish. Code Dash size Material/finish CC -4 through -6 Carbon Steel - cadmium plating CZ -4 thro

12、ugh -6 Carbon steel - zinc plating SS -4 through -6 Corrosion resistant steel - N/A AA -8 through -32 Aluminum - anodic coating TA -4 through -32 Titanium - anodized or fluoride phosphated Identification of product. The PIN and the manufacturers Commercial and Government Entity (CAGE) code or tradem

13、ark shall be permanently marked on the assembly, see figure 1, or on a removable tag securely attached to the assembly. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Provided by

14、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27223C 4 Referenced documents. In addition to MIL-DTL-5070, this document references the following: MS27224 MS27234 MS27236 MS27238 MS27239 AWS C3.4 AWS C3.5 AWS C3.6 AWS C3.7 SAE-AMS-H-6875 SAE-AMS2672 SAE-AMS27

15、70 SAE-AMS2801 SAE-AS4370 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-042) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force - 11, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-