DLA MS27064 REV D-2003 ELBOW SUBASSEMBLY SWIVEL FLANGE 45 DEG 《45度旋转法兰弯管组件》.pdf

《DLA MS27064 REV D-2003 ELBOW SUBASSEMBLY SWIVEL FLANGE 45 DEG 《45度旋转法兰弯管组件》.pdf》由会员分享，可在线阅读，更多相关《DLA MS27064 REV D-2003 ELBOW SUBASSEMBLY SWIVEL FLANGE 45 DEG 《45度旋转法兰弯管组件》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A 1 of 3 FSC 4730 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. INCH-POUND MS27064D 24 September 2003 SUPERSEDING MS27064C 30 June 1972 DETAIL SPECIFICATION SHEET ELBOW SUBASSEMBLY, SWIVEL FLANGE, 45 This specification is approved for use by all Departments

2、 and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-DTL-27272. NOTES: 1. Dimension A is measured between the hose end of the threaded section of the union and the free end of the insert at its centerline.

3、 2. Dimension B is measured between the centerline of the nipple and the free end of the insert at its centerline. 3. Any bent tube design of subassembly components to the left of plane A-A is acceptable provided that the requirements of this specification sheet and the procurement specification are

4、 met. FIGURE 1. Elbow subassembly illustration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27064D 2 REQUIREMENTS Intended use. This part is a component of MS27056. Identification of product. The Part or Identifying Number (PIN) and the manufac

5、turers trademark shall be permanently marked on the assembly. The PIN for this assembly shall be as specified in table I (e.g., MS27064-8C). Dimensions. Dimensions are in inches. Material. PIN suffix C, corrosion-resistant steel. PIN suffix D. Aluminum alloy. No PIN suffix. Combination of aluminum a

6、lloy and corrosion-resistant steel. See applicable specification sheet for other components identified in table I for their material requirements. Finish. Corrosion-resistant steel, do not passivate. Aluminum alloy. Anodize in accordance with MIL-A-8625, type II, dye blue. Order of precedence. This

7、specification takes precedence over the documents referenced herein. Unless otherwise specified, referenced documents shall be of the issue in effect on the date of solicitation. Elbow subassembly illustration. See figure 1. TABLE I. Elbow subassembly composition. PIN Wire PIN Union, nipple PIN Elbo

8、w, nipple end PIN A 1/ .035 B 2/.035 MS27064 MS27072 MS27071 MS27084 -8C -8C -8C -8C 1.266 .338 -8 -8D -10C -10C -10C -10C 1.324 .375 -10 -10D -10D -12C -12C -12C -12C 1.782 .468 -12 -12D -12D -16C -16C -16C -16C 1.838 .505 -16 -16D -16D -20C -20C -20C -20C 2.052 .569 -20 -20D -20D -24C -24C -24C -2

9、4C 2.318 .624 -24 -24D -24D 1/ Dimension A is measured between the hose end of the threaded section of the union and the free end of the insert at its centerline. 2/ Dimension B is measured between the centerline of the nipple and the free end of the insert at its centerline. Provided by IHSNot for

10、ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27064D 3 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. CONCLUDING MATETRIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4730-0868-033) DLA - CC Review activities: Army - AR, AT, MI Navy - MC, SA, SH Air Force - 71 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-