DLA MS27034 REV K-2009 CONNECTORS RECEPTACLE ELECTRICAL PIN INSERT CYLINDRICAL MINIATURE HERMETIC SOLDER MOUNT [Use DLA MIL-DTL-83723 G SUPP 1 DLA MIL-DTL-83723 G DLA MIL-DTL-83723.pdf

《DLA MS27034 REV K-2009 CONNECTORS RECEPTACLE ELECTRICAL PIN INSERT CYLINDRICAL MINIATURE HERMETIC SOLDER MOUNT [Use DLA MIL-DTL-83723 G SUPP 1 DLA MIL-DTL-83723 G DLA MIL-DTL-83723.pdf》由会员分享，可在线阅读，更多相关《DLA MS27034 REV K-2009 CONNECTORS RECEPTACLE ELECTRICAL PIN INSERT CYLINDRICAL MINIATURE HERMETIC SOLDER MOUNT [Use DLA MIL-DTL-83723 G SUPP 1 DLA MIL-DTL-83723 G DLA MIL-DTL-83723.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, PIN INSERT, CYLINDRICAL, MINIATURE, HERMETIC, SOLDER MOUNT This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of

2、 this specification sheet and MIL-DTL-26500. FIGURE 1. Receptacle, class H (hermetic) dimensions. AMSC N/A FSC 5935 MS27034K 20 August 2009 SUPERSEDING MS27034J 6 February 2004 Inactive for new design after 14 November 1977. For new design, use MIL-DTL-83723, series III. INCH-POUNDProvided by IHSNot

3、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27034K 2Inches mm Inches mm .005 0.13 .100 2.54 .015 0.38 2.77 Inches .016 mm 0.41 Inches .133 mm 3.38 .018 0.46 .153 3.89 .019 0.48 .281 7.14 .020 0.51 .378 9.60 .022 0.56 .380 9.65 .025 0.64 .392 9.96 .031 0.79 .490

4、12.45 .047 1.19 .540 13.72 .062 1.57 .560 14.22 .078 1.98 .704 17.88 .079 2.01 .734 18.64 Type T (style P) FIGURE 1. Receptacle, class H (hermetic) dimensions Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27034K 3Type B (style P) FIGUR

5、E 1. Receptacle, class H (hermetic) dimensions Continued. Inches mm .004 0.10 .005 0.13 .010 0.25 .366 9.29 .377 9.57 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27034K 4Shell size A CPLG UNEF-2A B dia C dia + .005 (0.13)- .000 (0.00)E max Inse

6、rt dia (see note 9)F max dia G max dia HH dia + .010 (0.25)- .000 (0.00)8 .562-24 (14.27) .505 (12.83) .428 (10.87) .312 (7.92) .437 (11.10).561 (14.25) .442 (11.23) 10 .687-24 (17.45) .636 (16.15) .530 (13.46) .388 (9.86) .562 (14.27).696 (17.68) .567 (14.40) 12 .875-20 (22.22) .805 (20.47) .700 (1

7、7.78) .558 (14.17) .750 (19.05).875 (22.22) .755 (19.18) 14 .937-20 (23.80) .875 (22.22) .769 (19.53) .627 (15.92) .812 (20.62).935 (23.75) .817 (20.75) 16 1.062-18 (26.97) 1.002 (25.45) .896 (22.76) .754 (19.15) .937 (23.80)1.062 (26.97) .942 (23.93) 18 1.187-18 (30.15) 1.108 (28.14) 1.002 (25.45)

8、.860 (21.84) 1.062 (26.97)1.187 (30.15) 1.067 (27.10) 20 1.312-18 (33.32) 1.233 (31.32) 1.127 (28.62) .985 (25.02) 1.182 (30.15)1.312 (33.32) 1.187 (30.15) 22 1.437-18 (36.50) 1.358 (34.49) 1.252 (31.80) 1.110 (28.19) 1.312 (33.32)1.437 (36.50) 1.317 (33.45) 24 1.562-18 (39.67) 1.483 (37.67) 1.377 (

9、34.98) 1.235 (31.37) 1.432 (36.50)1.562 (39.67) 1.437 (36.50) FIGURE 1. Receptacle, class H (hermetic) dimensions Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27034K 5Shell size JJ dia flange + .020 (0.51) KK dia +.000 (0.00) -.005 (0

10、.13) N +.000 (0.00) -.004 (0.10) NN +.000 (0.00) -.003 (0.08) P +.000 (0.00) -.005 (0.13) UU +.000 (0.00) -.009 (-0.23) 8 .705 (17.91) .536 (13.61) .101 (2.56) .078 (1.93) .076 (1.93) .310 (7.87) 10 .840 (21.34) .659 (16.74) .094 (2.39) .093 (2.36) .089 (2.26) .374 (9.50) 12 1.045 (26.54) .829 (21.0

11、6) .094 (2.39) .093 (2.36) .089 (2.26) .459 (11.66) 14 1.090 (27.69) .898 (22.81) .094 (2.39) .093 (2.36) .089 (2.26) .494 (12.55) 16 1.210 (30.73) 1.025 (26.03) .094 (2.39) .093 (2.36) .089 (2.26) .557 (14.15) 18 1.340 (34.04) 1.131 (28.73) .094 (2.39) .093 (2.36) .089 (2.26) .610 (15.49) 20 1.475

12、(37.46) 1.256 (31.90) .094 (2.39) .093 (2.36) .089 (2.26) .673 (17.09) 22 1.590 (40.39) 1.381 (35.08) .094 (2.39) .093 (2.36) .089 (2.26) .735 (18.67) 24 1.725 (43.82) 1.506 (38.25) .094 (2.39) .093 (2.36) .089 (2.26) .798 (20.27) FIGURE 1. Receptacle, class H (hermetic) dimensions Continued. Provid

13、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27034K 6Size of contact Type of contact AA BB dia CC dia minDD EE dia FF max 12 Solder cup .150 (3.81) .112 (2.84) .095/.093 (2.41/2.36) .400 (10.16)12 Eyelet .035 (0.89) .112 (2.84) .200 (5.08) .095/.093 (

14、2.41/2.36) .400 (10.16)16 Solder cup .103 (2.62) .069 (1.75) .063/.061 (1.60/1.55) .400 (10.16)16 Eyelet .025 (0.64) .069 (1.75) .125 (3.18) .063/.061 (1.60/1.55) .400 (10.16)20 Solder cup .077 (1.96) .042 (1.07) .041/.039 (1.04/.99) .330 (8.38) 20 Eyelet .015 (0.38) .042 (1.07) .080 (2.03) .041/.03

15、9 (1.04/0.99) .330 (8.38) Position Shell size 8 Shell size 10 Shell sizes 12 thru 24 E F G E F G E F G Normal 60 180 300 60 180 300 50 170 290 6 46 166 286 46 166 286 50 170 290 7 46 166 286 46 166 286 50 170 290 8 60 180 300 60 180 300 50 170 290 9 89 209 329 89 209 329 50 170 290 Y 60 180 300 50 1

16、70 290 NOTES: 1. Dimensions in inches. Unless otherwise specified, tolerances-decimals .005. 2. Metric equivalents are given for general information only. 3. All diameters to be concentric with each other within .015 T.I.R. 4. All diameters in the same plane to be concentric with each other with .00

17、4 T.I.R. 5. Contacts to be in accordance with SAE-AS39029. True position (T.P.) tolerances specified are for maximum material conditions (M.M.C). 6. For accessories used with this connector see procurement specification. 7. Thread relief groove is optional on shell. When groove is omitted the length

18、 of full thread from front of shell will be .310 minimum and thread runout .385 maximum. 8. For insert arrangements and alternate insert keying positions: See MIL-STD-1554. 9. Resilient face gasket only. FIGURE 1. Receptacle, class H (hermetic) dimensions Continued. Provided by IHSNot for ResaleNo r

19、eproduction or networking permitted without license from IHS-,-,-MS27034K 7Weight chart Maximum connector weight in pounds Pin insert MS PIN Solder cup contacts MS27034H8T2CN MS27034H10T2CN .033 (0.84) MS27034H10T5CN .033 (0.84) MS27034H10T20CN .034 (0.86) MS27034H12T3CN .050 (1.27) MS27034H12T12CN

20、.050 (1.27) MS27034H14T3CN MS27034H14T4CN .060 (1.52) MS27034H14T7CN .056 (1.42) MS27034H14T12CN MS27034H14T15CN .058 (1.47) MS27034H16T10CN MS27034H16T24CN .066 (1.68) MS27034H18T8CN .090 (2.29) MS27034H18T11CN MS27034H18T14CN .087 (2.21) MS27034H18T31CN .085 (2.16) MS27034H20T16CN MS27034H20T25CN

21、MS27034H20T28CN MS27034H20T39CN MS27034H20T41CN MS27034H22T12CN MS27034H22T19CN .117 (2.97) MS27034H22T32CN MS27034H22T55CN .118 (3.00) MS27034H24T43CN MS27034H24T57CN MS27034H24T61CN FIGURE 2. Receptacle, class H (hermetic) weights. Provided by IHSNot for ResaleNo reproduction or networking permitt

22、ed without license from IHS-,-,-MS27034K 8Weight chart Maximum connector weight in pounds Pin insert MS PIN Eyelet contacts MS27034H8T2EN MS27034H10T2EN .032 (0.81) MS27034H10T5EN .032 (0.81) MS27034H10T20EN .033 (0.84) MS27034H12T3EN .050 (1.27) MS27034H12T12EN .049 (1.24) MS27034H14T3EN MS27034H14

23、T4EN .059 (1.50) MS27034H14T7EN .055 (1.40) MS27034H14T12EN MS27034H14T15EN .057 (1.45) MS27034H16T10EN MS27034H16T24EN .065 (1.65) MS27034H18T8EN .090 (2.29) MS27034H18T11EN MS27034H18T14EN .086 (2.18) MS27034H18T31EN .082 (2.08) MS27034H20T16EN MS27034H20T25EN MS27034H20T28EN MS27034H20T39EN MS270

24、34H20T41EN MS27034H22T12EN MS27034H22T19EN .115 (2.92) MS27034H22T32EN MS27034H22T55EN .115 (2.92) MS27034H24T43EN MS27034H24T57EN MS27034H24T61EN Notes: 1. Dimensions are in inches. 2. Metric equivalent are given for information only. FIGURE 2. Receptacle, class H (hermetic) weights Continued. Prov

25、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27034K 9REQUIREMENTS: Dimensions and configuration: See figures 1 and 2. Connector mating: This connector mates with MS24266 and MS27615. Part or Identifying Number (PIN) example: MS27034 H 18 - T 31 C N

26、MS number Class Shell size Coupling type Contact arrangement Style C Solder cup E Eyelet Alternate insert Position (“N” used for normal position) Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of

27、the changes. Referenced documents. In addition to MIL-DTL-26500, this document references the following: MIL-DTL-83723 SAE-AS39029 MIL-STD-1554 MS24266 MS27615 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27034K 10CONCLUDING MATERIAL Custodians:

28、 Preparing activity: Air Force 85 DLA CC DLA CC (Project 5935-2009-121) Review activity: Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-