DLA MS25325 REV P-2003 RELAYS ELECTROMAGNETIC 5 AMPERES 4 PDT TYPE I SOCKET MOUNTED HERMETICALLY SEALED《I型4 PDT 5安培火箭安装密封电磁继电器》.pdf

《DLA MS25325 REV P-2003 RELAYS ELECTROMAGNETIC 5 AMPERES 4 PDT TYPE I SOCKET MOUNTED HERMETICALLY SEALED《I型4 PDT 5安培火箭安装密封电磁继电器》.pdf》由会员分享，可在线阅读，更多相关《DLA MS25325 REV P-2003 RELAYS ELECTROMAGNETIC 5 AMPERES 4 PDT TYPE I SOCKET MOUNTED HERMETICALLY SEALED《I型4 PDT 5安培火箭安装密封电磁继电器》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A 1 of 5 FSC 5945 INCH-POUND MS25325P 27 November 2003 SUPERSEDING MS25325N 20 Jan 1989 RELAYS, ELECTROMAGNETIC, 5 AMPERES, 4 PDT, TYPE I, SOCKET MOUNTED, HERMETICALLY SEALED INACTIVE FOR NEW DESIGN AFTER 5 JUN 1987 NO SUPERSEDING SPECIFICATION FOR NEW DESIGN USE MIL-PRF-83536/5 OR /6 This sp

2、ecification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-PRF-6106. FIGURE 1. Dimensions and configurations.Provided by IHSNot for ResaleNo re

3、production or networking permitted without license from IHS-,-,-MS25325P 2 Inches mm Inches mm .001 0.03 .203 5.16 .005 0.13 .264 6.71 .008 0.20 .304 7.72 .010 0.25 .344 8.74 .040 1.02 .352 8.94 .047 1.19 .440 11.18 .062 1.57 .456 11.58 .075 1.91 .528 13.41 .088 2.24 .608 15.44 .093 2.36 1.031 26.19

4、 .143 3.63 1.500 38.10 .147 3.73 1.812 46.02 .152 3.86 1.844 46.84 .176 4.47 2.187 55.55 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 (0.25 mm). 4. Terminal numbers need not appear on relay headers

5、provided there is affixed positively identifies each terminal location specified herein. 5. The use of diodes on ac relays is optional. Actual application must be shown on label. 6. Pins to be perpendicular to header surface within one degree. 7. In the event of conflict between the text of this sta

6、ndard and the references cited herein, the text of this standard shall take precedence. 8. Referenced Government documents of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DODISS) specified in the solicitation forms a part of this standard to the

7、extent specified herein. 9. Socket pin terminals shall provide the operational, environmental, and interface characteristics to provide a reliable interconnect to gold-plated contacts. Terminals shall be gold plated. One system for gold plating that may be used is ASTM B488, type 3, class 1.25 with

8、a nickel underplate of 50 to 150 microinches thick. The gold plating system shall enable the product to meet the performance requirements of this specification and shall be approved by the qualifying activity. 10. Gasket shall provide a reliable seal between the relay and mating socket that will mee

9、t the environmental, operational, and interface requirements of the relay with the mating socket. The gasket shall have thickness .075, recess .047 in bracket .005. Gasket material according to AMS 3332 has been considered acceptable. 11. Gasket shall provide a reliable seal between the relay and ma

10、ting socket that will meet the environmental, operational, and interface requirements of the relay with the mating socket. The gasket shall have shore hardness 20 5, thickness .047 .008. Gasket material according to AMS 3332 has been considered acceptable. FIGURE 1. Dimensions and configurations - C

11、ontinued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25325P 3 TABLE I. Dash numbers and characteristics. Dash number MS25325- Type Coil Terminal type Max weight in pounds D1 I dc Plug in 0.29 A1 I ac Plug in 0.30 A2 I ac Plug in 0.30 TABLE II.

12、Operating characteristics. Coil data Time - (milliseconds maximum) Nominal Max Max pick-up voltage Contact Bounce Main Aux PIN MS 25325- Coil Volts 1/ Freq Hz Res Volts Amp Nor- mal 2/ High temptest Cont cur-rent test Hold volt- age 2/ Drop out volt- age 2/ Oper-ate 3/ Rel-ease 4/ NO NC NO NC D1 X1,

13、X2 28 dc N/A 29 0.13 18 19.8 22.5 7.0 1.5 20 20 2 2 - - A1 X1,X2 115 400 N/A 122 0.06 90 95 100 35 5.0 25 50 2 2 - - A2 X1,X2 115 50/ 60 400 N/A 122 0.07 90 95 100 35 5 25 50 2 2 - - 1/ CAUTION: Use of any coil voltage less than rated coil voltage will compromise the operation of the relay. 2/ Over

14、the temperature range. 3/ With nominal coil voltage. 4/ From nominal coil voltage. TABLE III. Rated contact load (amperes per pole) (case grounded). 28 V dc 115 V ac, 1 phase 115/200 V ac, 3 phase 1/ Main Aux Main Aux Main Aux Type of load Life operating cycles x 103NO NC NO NC 400 Hz 60 Hz 400 Hz 6

15、0 Hz 400 Hz 60 Hz 400 Hz 60 Hz See appropriate notes Resistive 100 5 5 5 4 Inductive 100 Inductive 20 3 3 3 2 Motor 100 1.5 1.5 1.5 1 Lamp 100 0.8 0.8 0.8 0.6 Transfer load 2/ Mechanical life reduced current 400 1.25 1.25 1.25 1 Mixed loads Applicable per specification 1/ Absence of value indicates

16、relay is not rated for 3-phase application. 2/ Transfer load indicates relay is suitable for transfer between unsynchronized ac power supplies at rating indicated. Environmental characteristics. Temperature range -70C to +125C Max altitude rating 80,000 ft Shock G-level 50 G Duration 11 ms Max durat

17、ion contact opening 10 sProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25325P 4 Vibration - sinusoidal G-level 10 G Frequency range 5 - 1,500 Hz Acceleration 15 G Electrical characteristics. Minimum insulation resistance, initial 100 megohms. Afte

18、r life or environmental tests 50 megohms. Dielectric strength (sea level). Initial After life tests Coil to case 1,000 V rms 1,000 V rms Aux contacts N/A N/A All other points 1,000 V rms 1,000 V rms Dielectric strength (altitude): 80,000 ftCoil to case 500 V rms Aux contacts All other points 500 V r

19、ms Max contact drop initial: 0.150 volt. After life test: 0.175 volt. Overload current (NO): 20 amperes. Rupture current 25 amperes. Duty rating: Continuous. RFI specification: MIL-STD-461. (Applicable to coil circuits of ac operated relays). Conformance inspection. Performance of groups B and C tes

20、ts are not applicable. Group A acceptance reports shall be submitted to the preparing activity on a yearly basis in order to retain qualification for this military standard sheet. Qualification by similarity: See MIL-PRF-6106. Provided by IHSNot for ResaleNo reproduction or networking permitted with

21、out license from IHS-,-,-MS25325P 5 NOTES Referenced documents. In addition to MIL-PRF-6106, this specification sheet references the following documents. (Government documents are available on line at http:/assist.daps.dla.mil/quicksearch or www.dodssp.daps.mil or from the Standardization Document O

22、rder Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). Society of Automotive Engineers documents are available from the Society of Automotive Engineers 400 Commonwealth Drive Warrendale, Pennsylvania, United States, 15096-0001. http:/www.sae.org STANDARDS Department of Defense MIL

23、-STD-461 - Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment Society of Automotive Engineers (SAE) SAE-AMS3332 - Silicone Rubber Extreme Low-Temperature Resistant, 15-30 Custodians: Preparing activity:NAVY - AS DLA - CC Air Force - 11 DLA - CC (

24、Project 5945-1221-08) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at www.dodssp.daps.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-