DLA MS14226-1982 WASHER FLAT FOR OVERSIZE FASTENERS& FASTENER SLEEVE《超大紧固件和紧固件轴套的平垫圈》.pdf

《DLA MS14226-1982 WASHER FLAT FOR OVERSIZE FASTENERS& FASTENER SLEEVE《超大紧固件和紧固件轴套的平垫圈》.pdf》由会员分享，可在线阅读，更多相关《DLA MS14226-1982 WASHER FLAT FOR OVERSIZE FASTENERS& FASTENER SLEEVE《超大紧固件和紧固件轴套的平垫圈》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MSLq226 53 m 7777732 0003888 7 I REQUIREMENTS: l. WTERIAL: CORROSION RESISTANT STEEL PER MIL-S-5059 OR MIL-S-6721 ALUHIHUI4 ALLOY PER QQ-A-250/5, CONDITI4 T3 OR T4 T -C CODE -D COOE 2. COATING: PASSIVATION PER 911-P-35 (FOR UNCOATED CRES) -NO COOE BLACK OXIDE COAT PER MIL-C-13924 LFOR CRES) -Y CODE

2、CHEMICAL CONVERSIOH PER MIL-C-5541 3 CLASS 3 (ALUMINUM ALLOY) -J COOE ANODIZE PER MIL-A-8625 (.ALUMINUM ALLOY) - -K CODE J m MILITARY STANDARD WASHERS, FLAT, FOR OVERSIZE FASTENERS AND FASTENER SLEEVES AF-11 MS 14226 ARMY-AV -1 W3 DD IZ 672-1 -? )1LllOUDm0*IOIWIOll“ PROJECT NO. 5310-1223 run W. L -.

3、 0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I M.SUPCiASS I 531 O TABLE I. WASHERS FORJ64 OVERSIZE FAS- AND FASTENER SLEEVES i A D DIA. DIA. + .O05 + .O20 T - .O00 - .O05 DASH NUMBERS IZE IN (OR COR. RESIST. STEEL ALUMINUM ALLOY - UNCOATED I CO

4、ATED COATING ONV NO. 8 (.185) .190 .375 .O32 L64C8 ! L64yc8“ I NO. 10 032 L64C10 L64Y Cl O f.210) I .215 I .438 I :O63 I 64C10 I 64YC10 I 64JD10 I , 114 (.333) .338 .562 “ :i:- (.270) ,275 E ._-o63 64YC416. 6450416 5/16 . D32 ;- L64C416 L64YC416 .O32 . 7/:95) .400 .625 .O63 L64C616 7/16 (.458) .463

5、.750 .O63 .D32 L64C716 L64YC716 64YC716 1 /2 (.520) .525 .E75 .D63 64C816 .O32 164C816 L64YC816 64YC816 64JD816 “. . . . - - - “ “ - . - - “ “ - . . “ -. “ . . _- “ “ NO. 8 TABLE II. WASHERS FOR 1/32 OVERSIZE FASTENERS - AND FASTENER SLEEVES ANODIZED SURFACES L64KD8 64KD1 O 64KD416 “_ 64K0516 64KD61

6、6 “_ - 64KD716 64KD816 1 DASH NUMBERS D + .O20 T - .O05 DIA. COR. RESIST. STEEL ALUMINUM ALLOY COATED CHEM. CONY. ANODIZED COATING SURFACES .375 ,438 .O63 32C10 32Y Cl O 32JD10 32KD1 O .O32 L32C8 L32YC8 L32JD8 L32KD8 .O32 L32C10 L32YC10 _“ - _“ “_ “ “ “ - -. - . . - -. . ._ . .O32 .500 a .O63 L32C41

7、6 L32YC416 32C416 32YC416 _ 32JD416 32KD416 .750 .O63 32C716 L 32YC716 I 3250716 .O32 L32C716 L32YC716 “ “ . . . - -. - - 32KD516 32KD616 32KD716 1 032 L32C816 L32YC816 .O75 1 :O63 I 32C816 1 32YC816 I 3250816 I 32KD816 I u: Rhw curt WASHERS, FLAT, FOR OVERSIZE IAW - W m .AFTTI .-2 “ .: FASTENERS AN

8、D FASTENER SLEEVES ARMY-AV . WREMENT UEClflCAllON SUCLRIEDLS: MILITARY MS 14226 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS1422b 53 W 7777712 0003870 5 m .a c I 8 NOTES: 1. .REMOYE ALL BURRS AND SHARP EDGES. 2. DIMENSIONS IN INCHES. 3. TOLERAN

9、CES ON: THICKNESS: .O32 r .004; .O63 f .O06 ALL OTHER DIMENSIONS: f .O10 4. SURFACE CHARACTERISTICS: WASHER FACES SHALL BE PARALLEL WITHIN .DO2 INCH. WASHER FACES SHALL BE FLAT WITHIN .O07 INCH. 5. “J“ CODE WASHERS WHEN LOW ELECTRICAL RESISTANCE REQUIRED. 6. “K“ CODE WASHERS WHERE CORROSION PROTECTI

10、ON PRIME CONSIDERATION. 7. EXAMPLE OF PART NUMBER: MS14226 L 64 Y C 516 = WASHER, FLAT, LIGHT SERIES, 1/64 OVERSIZE, BLACK OXIDE COAT, CRES, FOR 5/16 DIA PIN (OR SLEEVE) PIN SIZE (V16 DIA. PIN) MATERIAL CODE (SEE REQ. 1 AND TABLE I) I I I COATING CODE (SEE REQ. 2) I 1 OVERSIZE (64 DENOTES 1/64 OVERS

11、IZE) II (32 DENOTES 1/32 OVERSIZE) I-“ DENOTES REGULAR SERIES “L“ DENOTES LIGHT SERIES MS NUMBER B. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATIONS FOR BIOS, OR DATE OF THE ISSUE ADOPTED. REQUEST FOR PROPOSAL EXCEPT THAT REFERENCED ADOPTED INDUSTRY WCUMENTS StWLL GIVE THE 9. FOR DESIGN FEATURE PURPOSES, THIS STANDARD TAKES PRECEDENCE OVER PROCUREMENT DOCUMENTS REFERENCED HEREIN. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-