DLA MIL-S-64052-1988 SPRAY GUN PAINT HEAVY DUTY PRESSURE FEED《压力送料重型油漆喷枪》.pdf
《DLA MIL-S-64052-1988 SPRAY GUN PAINT HEAVY DUTY PRESSURE FEED《压力送料重型油漆喷枪》.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-S-64052-1988 SPRAY GUN PAINT HEAVY DUTY PRESSURE FEED《压力送料重型油漆喷枪》.pdf(19页珍藏版)》请在麦多课文档分享上搜索。
1、m-la-ti MIL-S-64052 47 7777906 O252775 I $-.- - i + MIL-S-64052 29 April 1988 SPRAY GUN, PAINT, HEAVY DUTY, PRESSURE FEED This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. Scope 1.1 Scope. This specification covers Pressure Feed, Heavy Duty, Pain
2、t Spray Gun assemblies, including the gun, cup, gages, regulator and valves, here after referred to as spray gun. 2. APPLICABLE DOCUMENTS 2.1 Government documents 2.1.1 Specifications and standards. The following specifications and standards form a part of this specification to the extent specified
3、herein. specified, the issue of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. Unless otherwise SPECIFICATIONS FEDERAL TT-E-489 PPP-B-60 1 PPP-B-621 PPP -B-636 PPP-F-320
4、 PPP-T-76 MILITARY MIL-P-23377 MIL-C-46 168 Enamel, Alkyd, Gloss (For Exterior and Interior Surfaces) Boxes, Wood, Cleated-Plywood Boxes, .Wood, Nailed and Lock-Corner Box, Shipping, Fiberboard Fiberboard: Grade) and Cut Shapes Tape, Packaging Paper (For Carton Sealing) Corrugated and Solid, Sheet S
5、tock (Container Primer Coatings: Coating, Aliphatic Polyurethane, Chemical Agent Epoxy-Polymide Chemical and Solvent Resistant Res i st ant Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Comman
6、der, US Army Armament Research and Development Engineering Center, ATTN: using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. SMCAR-ESTS, Rock Island, IL 61299-7300 by I f- -.+ 1 I FSC 4940 THIS DOCUMENT CONTAINS 7
7、PAGES. APEC N/A - . ._ DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-MIL-S-64052 44 W O6 025i776 T MIL-S-64052 MIL-P-52 192 MIL-T-8 1772 STANDARES FEDEM FED-STD-H28 MIL
8、ITARY MIL-STD- 1 O5 MIL-STD- 1 29 MILSTD- 130 MILSTD-889 MIL-STD-1190 - Primer Coating, Epoxy - Thinner, Aircraft Coating - Screw-Thread Standards For Federal3ervices - Sampling Procedures and Tables for Inspection - Marking For Shipment and Storage - Identification Marking of US Military Property -
9、 Dissimilar Metals - Minimum Guidelines For Level C Preservation, by Attributes Packing and Marking (Copies of specifications, standards, handbooks, drawings, and publications required by contractors in connection with specific acquisition functions should be obtained from the contracting activity o
10、r as directed by the contracting officer.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. may be available in or through libraries or other informational services, ) specification and the references cited
11、 herein (except for associated detail specification specification sheets or Ms standards) , the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. These documents als
12、o 2.2 Order of precedence. In the event of a conflict between the text of this 3.1 First arbicle. When specified in the contract or purchase order, a sanple shall be subjected to first article inspection (see q.2.1 and 5.2.1). 3.2 Design and construction. The spray gun shall be a conplete functional
13、 assembly consisting of the gun, cup, gages, regulator, valves, gaskets, tO11 rings, bushings and seals, The spray gun shall be new and of the manufacturers current commercial design, commercial/industrial production use. operation and designed with an air pressure fluid material atomizing/mixing ai
14、r cap. The spray gun shall be designed for pressure feed, The spray gun shall be designed and constructed to facilitate its complete disassembly and reassembly for cleaning and repair using simple hand tools, without damaging the spray gun and all spray gun components, The spray gun shall contain no
15、 burrs, slivers, or galling of the interior and exterior surfaces of the air and fluid passages before, during, and after each disassembly and reassembly, constructed of materials which are chemically conpatible with the coatings, enamels, lacquers, paints, solvents and thinners encountered during l
16、ife cycle use and cleaning of the spray gun. Materials which are chemically compatible shall be those materials that will not deteriorate or otherwise reduce life cycle operational functions/characteristics. The internal orifice of the fluid nozzle shall be The spray gun shall be designed for heavy
17、duty The spray gun shall be for hand held The spray gun and its components shall be 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-3.4.2 Threaded aluminum interfacing. Threaded aluminum/aluminum alloy parts or components of the spray gun shall not b
18、e screwed, fastened, or affixed to the male/female threaded aluminum parts of components. mating (male/female) threads and fasteners provides for physical bonding of the aluminum alloy materials, which interferes with and prevents, disassembly and reassembly of the spray gun without damage and degra
19、dation. Oxidation and corrosion of MILS-64052 centered to the functional exterior surface of the fluid nozzle within plus/minus 0.001 inch. the functional external surface of the fluid nozzle, shall not deviate more than 0.0015 inch when measured around the annular radial opening (see Figure 4, 3.13
20、.4 and 3.13.5). The spray gun shall include a pop-off pressure safety relief valve (see 3.13.2). The annular radial opening between the center hole of the air cap and 3.3 Interchangeability_. All parts of the spray gun shall be manufactured to definite standards and tolerances. interchangeable witho
21、ut requiring modification of the part or its mating components. All parts subject to possible future replacement shall be assigned a manufacturers part number and shall be identified in the repair parts nanual. parts shall provide the same or better form, fit, function, and performance as the parts
22、provided-or initially instailed in the end item. 3.4 Material. All parts of the spray gun shall be fabricated from new materials. In no event shall such processes as welding, peening, or filling with cold solders or metallic pastes be used for reclaiming any parts of the spray gun. All spray gun par
23、ts, except the gun body, in contact with the sprayable materials (see 3.7.1) shall be fabricated of bronze, brass, or stainless steel. All respective parts of the spray gun shall be All replacement 3.4.1 Dissimilar materials. Contact between dissimilar metals shall be avoided wherever possible on th
24、e spray gun and all accessory and ancillary equipment. such contact cannot be avoided, suitable protection against corrosion shall be applied in accordance with ?IILSTD-889. When 3.5 Threads, The design, manufacture and configuration of threads shall conform to FED-STD-H28 and the applicable detaile
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILS640521988SPRAYGUNPAINTHEAVYDUTYPRESSUREFEED 压力 重型 油漆 喷枪 PDF

链接地址:http://www.mydoc123.com/p-693439.html