DLA MIL-PRF-83726 36 D-2013 RELAY HYBRID TIME DELAY (ON RELEASE) CLASS B TYPE IIA HERMETICALLY SEALED 4PDT 10 AMPERES FIXED TIME DELAY 0 1 TO 600 SECONDS.pdf
《DLA MIL-PRF-83726 36 D-2013 RELAY HYBRID TIME DELAY (ON RELEASE) CLASS B TYPE IIA HERMETICALLY SEALED 4PDT 10 AMPERES FIXED TIME DELAY 0 1 TO 600 SECONDS.pdf》由会员分享,可在线阅读,更多相关《DLA MIL-PRF-83726 36 D-2013 RELAY HYBRID TIME DELAY (ON RELEASE) CLASS B TYPE IIA HERMETICALLY SEALED 4PDT 10 AMPERES FIXED TIME DELAY 0 1 TO 600 SECONDS.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、AMSC N/A FSC 5945 INCH-POUND MIL-PRF-83726/36D 6 March 2013 SUPERSEDING MIL-PRF-83726/36C 19 June 2012 PERFORMANCE SPECIFICATION SHEET RELAY, HYBRID, TIME DELAY (ON RELEASE), CLASS B, TYPE IIA, HERMETICALLY SEALED, 4PDT, 10 AMPERES, FIXED TIME DELAY, 0.1 TO 600 SECONDS This specification is approved
2、 for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-83726. FIGURE 1. Outline dimensions and configuration of relay. Provided by IHSNot for ResaleNo reproduction or net
3、working permitted without license from IHS-,-,-MIL-PRF-83726/36D 2 Inches mm Inches mm .001 0.03 .300 7.62 .002 0.05 .312 7.92 .005 0.13 .625 15.88 .040 1.02 .930 23.60 .050 1.27 1.025 26.04 .062 1.57 1.396 35.46 .150 3.81 1.446 33.73 .156 3.96 1.510 38.35 .200 5.08 1.718 43.64 .270 6.86 NOTES: 1. D
4、imensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 (0.25 mm) for three place decimals and .03 (0.76 mm) for two place decimals. 4. Terminal numbers shall not appear on the relay header and there shall be a legible c
5、ircuit diagram on relay which identifies each terminal location specified. 5. Gasket material: The gasket material shall be of such quality to ensure the relay meets all the performance requirements of this specification. Silicone rubber gasket in accordance with SAE- AMS 3332, shore hardness 15 to
6、35 has been considered acceptable. 6. Terminal composition: The terminal composition shall be of such quality to ensure the relay meets all the performance requirements of this specification. Gold in accordance with SAE-AMS 2422 or ASTM B488, Type 3; underplating: nickel, 50 microinches to 150 micro
7、inches thick; has been considered acceptable. 7. Terminal Y2 is not used. FIGURE 1. Outline dimensions and configuration of relay Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/36D 3 REQUIREMENTS: OPERATING REQUIREMENTS: Tim
8、ing action: Delay-on-release. Time delay: Fixed; select from 0.1 second to 600 seconds. Timing accuracy: 10 percent of nominal value. (The accuracy requirement applies for any combination of operating temperature and voltage. Add 10 ms for timing less than 1 second.) Recycle time: 50 milliseconds ma
9、ximum. (Recycle time is defined as the minimum time that power must be applied from the input terminals to assure that the next timing cycle will be completed within the specified timing tolerance. (Units can be recycled during timing or after time-out.) Power interrupt: 500 microseconds. (Transient
10、 and power loss specifications are based on a maximum duty cycle of 1/50.) Control voltage: 20 V dc to 30 V dc. Control current: 15 milliamperes maximum at 25C. Operating current: (X1-X2) 150 mA maximum at 25C. Extraneous voltage: 7 V dc minimum. INPUT REQUIREMENTS: Input voltage range: 20 V dc to 3
11、0 V dc. (EMI test limits will not be exceeded during the timing interval or when continuously energized under steady-state conditions in accordance with the EMI test of MIL-PRF-83726.) Duty rating: Continuous. Current drain: (quiescent)10 milliamperes maximum at 25C. Polarity protection: The timer s
12、hall be inoperative during, and undamaged by, reversal of the polarity of the operating voltage, or control voltage. OUTPUT REQUIREMENTS: Configuration: 4PDT. Life: See table I. TABLE I. Life load ratings (relay case grounded). Type of load Life (cycles) Amperes 28 V dc Amperes 115/200 V ac 400 Hz R
13、esistive Inductive Motor Lamp Low level 1/ 100,000 20,000 100,000 100,000 100,000 10 8 4 2 10 8 4 2 - 1/ Contact load 10 A to 50 A at 10 mV to 50 mV (dc or peak ac). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/36D 4 ELECTRICAL REQUI
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLAMILPRF8372636D2013RELAYHYBRIDTIMEDELAYONRELEASECLASSBTYPEIIAHERMETICALLYSEALED4PDT10AMPERESFIXEDTIMEDELAY01TO600SECONDSPDF

链接地址:http://www.mydoc123.com/p-693095.html