DLA MIL-DTL-83513 28 B-2009 CONNECTORS ELECTRICAL RECTANGULAR PLUG MICROMINIATURE POLARIZED SHELL STRAIGHT PIN CONTACTS 2 ROW SOLDER TYPE STANDARD PROFILE 9 THROUGH 37 CONTACTS PRI.pdf

《DLA MIL-DTL-83513 28 B-2009 CONNECTORS ELECTRICAL RECTANGULAR PLUG MICROMINIATURE POLARIZED SHELL STRAIGHT PIN CONTACTS 2 ROW SOLDER TYPE STANDARD PROFILE 9 THROUGH 37 CONTACTS PRI.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-83513 28 B-2009 CONNECTORS ELECTRICAL RECTANGULAR PLUG MICROMINIATURE POLARIZED SHELL STRAIGHT PIN CONTACTS 2 ROW SOLDER TYPE STANDARD PROFILE 9 THROUGH 37 CONTACTS PRI.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDMIL-DTL-83513/28B 18 March 2009 SUPERSEDING MIL-DTL-83513/28A 24 May 2004 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECTANGULAR, PLUG, MICROMINIATURE, POLARIZED SHELL, STRAIGHT, PIN CONTACTS, 2 ROW, SOLDER TYPE, STANDARD PROFILE, 9 THROUGH 37 CONTACTS, PRINTED CIRCUIT BOARD This s

2、pecification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83513. Inches mm .005 0.13 .0038 0.097 .010 0.25 .014 0.36 .015 0.38 .020 0.51 .025 0.64 .0

3、36 0.91 .050 1.27 .0669 1.699 .088 2.24 .096 2.44 .129 3.28 .140 3.56 .1848 4.694 .185 4.70 .190 4.83 .310 7.87 .355 9.02 FIGURE 1. Connector plug. AMSC NA FSC 5935 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/28B 2 Number of contact

4、s A Max B .005 (0.13) D 9 .785 (19.94) .565 (14.35) .3338 (8.478) 15 .935 (23.75) .715 (18.16) .4838 (12.289) 21 1.085 (27.56) .865 (21.97) .6338 (16.099) 25 1.185 (30.01) .965 (24.51) .7338 (18.639) 31 1.335 (33.91) 1.115 (28.32) .8838 (22.449) 37 1.485 (37.72) 1.265 (32.13) 1.0338 (26.259) FIGURE

5、1. Connector plug - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/28B 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are +.005 (0.13 mm)

6、. 4. Termination organization area is to be optionally molded or filled with a potting fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Plastic molding shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance w

7、ith ASTM D5927 or MIL-M-24519 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 5. Metal shell shall be of material in accordance with MIL-DTL-83513 for class M parts. 6. Jackpost (securely attached) when specified: Corrosion

8、 resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE-AMS-2700, type 2. Hardware will be attached in such a fashion as to not loosen during normal de-mating conditions, where as, the mating connector hardware does not e

9、xceed the following torque values: 2.5 inch pounds for #2-56 (arrangements A G) and 4.5 inch pounds for #4-40 (arrangement H). 7. Separately molded plastic body (if used) shall conform to type GDI-30F or type SDG-F in accordance with ASTM D5948 or GCT-30F in accordance with ASTM D5927 or MIL-M-24519

10、 or GST-40F in accordance with ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50 in accordance with ASTM D5138 or MIL-M-24519. 8. Wire termination pins shall conform to A-A-59551, number 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. 9. Termination lengths available:

11、 .109 (2.77 mm), .140 (3.56 mm) or .172 (4.37 mm). The tolerance shall be +.015 (0.381 mm) for all termination lengths. 10. Threaded insert, when specified: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivated in accordance with SAE

12、-AMS-2700, type 2. FIGURE 1. Connector plug - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/28B 4 FIGURE 2. Insert arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

13、-,-MIL-DTL-83513/28B NOTE: Engaging face of pin insert shown, cavity identification numbers are for reference only and do not appear on the part. FIGURE 2. Insert arrangement - Continued. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-8351

14、3/28B 6 FIGURE 3. Layout arrangement. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/28B 7 FIGURE 3. Layout arrangement - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-

15、DTL-83513/28B 8 Inches mm Inches mm .025 0.64 .225 5.72 .038 0.97 .600 15.24 .040 1.02 .750 19.05 .075 1.91 .900 22.86 .096 2.44 .965 24.51 .100 2.54 1.115 28.32 .183 4.65 1.265 32.13 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are for information only. 3. Unless otherwise specified, t

16、olerances are .005 (0.13 mm) 4. Patterns shown are for connector mounting side of PC board. FIGURE 3. Layout arrangement - Continued. REQUIREMENTS: Dimensions and configurations: See figures 1, 2 and 3. Current rating, maximum: 3 amperes per contact. Materials: Termination organization area: Potting

17、 fill material capable of passing the electrical and environmental requirements of MIL-DTL-83513. Shell: The requirements for shell materials shall be in accordance with MIL-DTL-83513. Plastic body or plastic molding: Shall be in accordance with the requirements of GDI-30F or SDG-30F of ASTM D5948,

18、or GPT-30F or GET-30F or GCT-30F of ASTM D5927 or MIL-M-24519 or GST-40F of ASTM D4067 or MIL-M-24519 or GLCP-30F or GLCP-50F in accordance with ASTM D5138 or MIL-M-24519. Jackpost: Corrosion resistant steel in accordance with ASTM A484/A484M and ASTM A582/A582M, 300 series stainless steel, passivat

19、ed in accordance with SAE-AMS-2700, type 2. Wire termination pins: Wire termination pins shall conform to A-A-59551, no. 24 AWG copper, except shall be tin-lead plated with a minimum of 3 percent lead. Mating connector: Shall be in accordance with MIL-DTL-83513/2 and MIL-DTL-83513/4. Plating of term

20、ination leads: Solder dipping of termination leads will be accomplished in SN60 PB40 or SN63 PB37 in accordance with J-STD-006. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83513/28B 9 Part or Identifying Number (PIN): The PIN shall consis

21、t of the letter M, the basic number of the specification sheet, a letter from the insert, a numerical code for the termination length, and a letter code for the shell finish and hardware column. M83513/28- A 01 C P Specification sheet number Insert arrangements (see figure 2) Terminationlength Shell

22、 finish (interface critical) Hardware A = 09 B = 15 C = 21 01 = .109 02 = .140 03 = .172 A = Pure electrodeposited aluminum C = Cadmium N = No hardware or threaded insert P = jackpost attach D = 25 K = Zinc nickel T = threaded insert E = 31 N = electroless nickel W = jackpost and threaded insertF =

23、37 (space applications only) P = Passivated Stainless Steel T = Nickel fluorocarbon polymer Changes from previous issue: The margins of this specification are marked with vertical lines to indicate where changes from previous issue were made. This was done as a convenience only and the Government as

24、sumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition

25、 to MIL-DTL-83513, this document references the following: MIL-DTL-83513/2 ASTM A484/A484M A-A-59551 MIL-DTL-83513/4 ASTM A582/A582M J-STD-006 MIL-M-24519 ASTM D4067 SAE-AMS-2700 ASTM D5138 ASTM D5927 ASTM D5948 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

26、m IHS-,-,-MIL-DTL-83513/28B 10 CONCLUDING MATERIAL Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project: 5935-2007-076) NASA - NA DLA - CC Review activities Army - AT, CR4, MI Navy - AS, CG, MC, SH Air Force - 99 NOTE: The activities listed above were interested in th

27、is document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-