DLA MIL-PRF-83726 29 J-2013 RELAY HYBRID TIME DELAY (ON RELEASE) CLASS B TYPE IIA HERMETICALLY SEALED DPDT 10 AMPERES FIXED TIME 0 1 TO 500 SECONDS.pdf

《DLA MIL-PRF-83726 29 J-2013 RELAY HYBRID TIME DELAY (ON RELEASE) CLASS B TYPE IIA HERMETICALLY SEALED DPDT 10 AMPERES FIXED TIME 0 1 TO 500 SECONDS.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-83726 29 J-2013 RELAY HYBRID TIME DELAY (ON RELEASE) CLASS B TYPE IIA HERMETICALLY SEALED DPDT 10 AMPERES FIXED TIME 0 1 TO 500 SECONDS.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5945 INCH-POUND MIL-PRF-83726/29J 04 March 2013 SUPERSEDING MIL-PRF-83726/29H 14 June 2012 PERFORMANCE SPECIFICATION SHEET RELAY, HYBRID, TIME DELAY (ON RELEASE), CLASS B, TYPE IIA, HERMETICALLY SEALED, DPDT, 10 AMPERES, FIXED TIME, 0.1 TO 500 SECONDS This specification is approved for

2、use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-83726. FIGURE 1. Outline dimensions and configuration of relay. Provided by IHSNot for ResaleNo reproduction or networki

3、ng permitted without license from IHS-,-,-MIL-PRF-83726/29J 2 Inches mm Inches mm .001 0.03 .300 7.62 .002 0.05 .312 7.92 .005 0.13 .625 15.88 .040 1.02 .930 23.60 .050 1.27 1.010 25.65 .062 1.57 1.025 26.04 .150 3.81 1.396 35.46 .156 3.96 1.446 33.73 .200 5.08 1.718 43.64 FIGURE 1. Outline dimensio

4、ns and configuration of relay Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/29J 3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is

5、 .010 (0.25 mm) for three place decimals and .03 (0.76 mm) for two place decimals. 4. Terminal numbers shall not appear on the relay header and there shall be a legible circuit diagram on relay which identifies each terminal location specified. 5. Gasket material: The gasket material shall be of suc

6、h quality to ensure the relay meets all the performance requirements of this specification. Silicone rubber gasket SAE-AMS-3332, shore hardness 20 5 has been considered acceptable. 6. Terminal composition: The terminal composition shall be of such quality to ensure the relay meets all the performanc

7、e requirements of this specification. Gold in accordance with SAE-AMS-2422 or ASTM-B488, Type 3; underplating: nickel, 50 microinches to 150 microinches thick; has been considered acceptable. 7. Terminal C2 is optional. FIGURE 1. Outline dimensions and configuration of relay Continued. Provided by I

8、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/29J 4 REQUIREMENTS: OPERATING REQUIREMENTS: Timing action: Delay-on-release. Time delay: Fixed; select from 0.1 second to 500 seconds. Timing accuracy: 10 percent of nominal value. (The accuracy requir

9、ement applies for any combination of operating temperature and voltage. Add 10 ms for timing less than 1 second.) Recycle time: 50 milliseconds maximum. (Recycle time is defined as the minimum time that power must be applied from the input terminals to assure that the next timing cycle will be compl

10、eted within the specified timing tolerance. (Units can be recycled during timing or after time-out.) Power interrupt: 500 microseconds. (Transient and power loss specifications are based on a maximum duty cycle of 1/50.) Extraneous voltage: 7 V dc minimum. Control voltage: 20 V dc to 30 V dc. Contro

11、l current: 15 milliamperes maximum at 25C. Operating current: (X1-X2) 150 mA maximum at 25C. INPUT REQUIREMENTS: Input voltage range: 20 V dc to 30 V dc. (EMI test limits will not be exceeded during the timing interval or when continuously energized under steady-state conditions in accordance with t

12、he EMI test of MIL-PRF-83726.) Duty rating: Continuous. Current drain: (quiescent): 10 milliamperes maximum at 25C. Polarity protection: The timer shall be inoperative during, and undamaged by, reversal of the polarity of the operating voltage, or control voltage. OUTPUT REQUIREMENTS: Configuration:

13、 DPDT. Life: See table I. TABLE I. Life load ratings (relay case grounded). Type of load Life (cycles) Amperes 28 V dc Amperes 115/200 V ac 400 Hz Resistive Inductive Motor Lamp Low level 1/ 100,000 20,000 100,000 100,000 100,000 10 8 4 2 10 8 4 2 - 1/ Contact load 10 A to 50 A at 10 mV to 50 mV (dc

14、 or peak ac). ELECTRICAL REQUIREMENTS: Transients: In accordance with MIL-STD-704 for 28 volts dc system. Spike: Self-generated: 50 volts maximum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/29J 5 Spike transients: 600V, 10 microsec

15、onds maximum. Susceptibility: + 80 V maximum; -600 V maximum. Electromagnetic interference: In accordance with MIL-STD-461(methods CS101, CS114, RS101, and RS103) for PINs with suffix letter W. (EMI test limits will not be exceeded during the timing interval or when continuously energized under stea

16、dy-state conditions in accordance with the EMI test of MIL-PRF-83726.) Insulation resistance: 1,000 megohms at 500 V dc at sea level, and 100 V dc at 80,000 feet between each pin and case. (Terminals X1 and X2 must be connected together during this test. Insulation resistance is measured between all

17、 mutually insulated terminals and between all terminals and case.) Dielelectric withstanding voltage: 1,000 V rms at 60 Hz at sea level, and 350 V rms at 80,000 feet between case and pins connected together. (Terminals X1 and X2 must be connected together during this test. Dielectric withstanding vo

18、ltage is measured between all mutually insulated terminals and between all terminals and case.) ENVIRONMENTAL REQUIREMENTS: Ambient temperature (operating or nonoperating): -55C to +125C. Vibration (sinusoidal): 30 gs, 10 Hz to 3,000 Hz. Vibration (random): 0.4 g2/Hz power spectral density, 50 Hz to

19、 2,000 Hz in accordance with MIL-STD-202, method 214, test condition 1G. Duration of 15 minutes each plane. Shock (specified pulse): 100 gs, 6 ms 1 ms, sine, 3 axes. Acceleration: 15 gs in any axis. Seal: Hermetic. Maximum altitude rating: 80,000 feet. Provided by IHSNot for ResaleNo reproduction or

20、 networking permitted without license from IHS-,-,-MIL-PRF-83726/29J 6 PHYSICAL REQUIREMENTS: Dimensions and configuration: See figure 1. Mating socket: MIL-DTL-12883/40-01, MIL-DTL-12883/40-05, MIL-DTL-12883/40-07, MIL-DTL-12883/40-11, MIL-DTL-12883/40-13, MIL-DTL-12883/40-17, MIL-DTL-12883/40-19,

21、or MIL-DTL-12883/40-23. (CAUTION: Consideration should be given to ambient temperature and current requirements when using wire barrels size 20.) Terminations: See figure 1. Terminal strength: 3 pounds pull. Weight: 2.5 ounces maximum. Marking: See MIL-PRF-83726. In addition, relays shall be marked

22、with the ESDS identifier as specified in MIL-STD-1285. Part or Identifying Number (PIN): Consists of the prefix M83726/29-, a four digit dash number (time delay expressed in milliseconds), and a suffix letter (P for plug-in; S for solder lug): M 83726/29- 1001 P Military designation Specification sh

23、eet number The first three digits are significant; the fourth is the number of zeros to follow the first three digits. The time is expressed in milliseconds and converted to seconds. (See examples.) Suffix letter. (Any relay numbered prior to the date of this specification shall be considered interc

24、hangeable with same mounting type, store and issue.) Examples: M83726/29-1001P 0.1 to 1 second time delay, plug-in. M83726/29-9002S 9 to 90 second time delay, solder lug. NOTE: Time delay relays within the 0.1 second to 500 second delay range are available within a one-decade range. The PIN represen

25、ts the upper timing limit of each range. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidde

26、rs and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-PRF-83726, this document references the following: MIL-STD-202 MIL-S

27、TD-461 MIL-STD-704 MIL-STD-1285 ASTM-B488 SAE-AMS-2422 SAE-AMS-3332 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-83726/29J 7 Custodians: Preparing activity: Navy - EC DLA - CC Air Force - 85 DLA - CC (Project 5945-2013-007) Review activiti

28、es: Navy - OS Air Force - 19 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-