DLA MIL-PRF-39012 31 C-2013 CONNECTORS COAXIAL RADIO FREQUENCY (SERIES TNC (UNCABLED RECEPTACLES SOCKET JAM NUT MOUNTED CLASS 2).pdf

《DLA MIL-PRF-39012 31 C-2013 CONNECTORS COAXIAL RADIO FREQUENCY (SERIES TNC (UNCABLED RECEPTACLES SOCKET JAM NUT MOUNTED CLASS 2).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-PRF-39012 31 C-2013 CONNECTORS COAXIAL RADIO FREQUENCY (SERIES TNC (UNCABLED RECEPTACLES SOCKET JAM NUT MOUNTED CLASS 2).pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 MIL-PRF-39012/31C 12 September 2013 SUPERSEDING MIL-C-39012/31B 22 December 1983 PERFORMANCE SPECIFICATION SHEET CONNECTORS, COAXIAL, RADIO FREQUENCY (SERIES TNC (UNCABLED RECEPTACLES, SOCKET, JAM NUT MOUNTED, CLASS 2) This specification is approved for use by all Departments and A

2、gencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39012. NOTES: 1. Dimensions are in inches. 2. For dimension A and B, see table I. 3. Metric equivalents are given for information only. 4. All undim

3、ensioned pictorial configurations are for reference purposes only. 5. Wrench flats to accommodate standard wrench opening per ASME B107.100-2010. 6. Full threads to within .063 (1.60 mm) of shoulder; 1 1/2 maximum uneven threads to shoulder. 7. There shall be a solid barrier in the socket between th

4、e pin entry and the solder pocket to prevent solder wicking. FIGURE 1. General configuration. Inches mm .022 .059 .063 .087 .099 .153 .156 .159 .181 .184 .187 .190 .368 .375 .380 .384 .429 .434 .4375 .439 .443 .470 .495 .505 .508 .515 .585 0.56 1.50 1.60 2.21 2.51 3.89 3.96 4.04 4.60 4.67 4.75 4.83

5、9.35 9.53 9.65 9.75 10.90 11.02 11.11 11.15 11.25 11.94 12.57 12.83 12.90 13.08 14.86 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/31C 2 NOTES: 1. Metric equivalents are given for general information only. 2. All undimensi

6、oned pictorial configurations are for reference purposes only. 3. N dimension applies to that portion (if applicable) of the dielectric which protrudes beyond the metal shoulder (or reference plane) by dimension K. FIGURE 2. Mating dimensions for socket terminations. Ltr Dimensions in inches with me

7、tric equivalents (mm) in parentheses Minimum Maximum A .378 (9.60) .381 (9.68) B .345 (8.76) .356 (9.04) C .327 (8.31) .333 (8.46) D .319 (8.10) .321 (8.15) E .186 (4.72) F .068 (1.73) .088 (2.24) G .329 (8.36) .333 (8.46) H .187 (4.75) J .186 (4.72) .206 (5.23) K .006 (.15) L .195 (4.95) M .081 (2.

8、06) .087 (2.21) N .256 (6.50) P .188 (4.78) .208 (5.28) R .415 (10.56) S .015 (.38) .030 (.76) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/31C 3 TABLE I. Dash number and overall dimensions. Dash no. Dim Inches-millimeters 1/ Maximum

9、 panel thickness Minimum panel thickness Minimum Maximum 0001 A B .529 (13.44) 1.187 (30.15) .653 (16.59) .125 (3.18) .045 (1.14) 0002 2/ A B .654 (16.61) 1.312 (33.32) .778 (19.76) .250 (6.35) .045 (1.14) 0003 A B .654 (16.61) 1.312 (30.15) .778 (19.76) .260 (6.35) .045 (1.14) 1/ Millimeters are in

10、 parentheses. 2/ Not for use in air force equipment. TABLE II. Group qualification. Group Submission and qualification of any of the following connectors Qualifies the following Connectors I /31-0001 /31-0002 /32-0001 /31-0001 /31-0002 /32-0001 ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency

11、 range: 0 to 11,000 MHz. Voltage rating: 500 volts rms maximum working voltage at sea level; 125 volts rms maximum at 70,000 feet. Temperature rating: -65 to +165C. REQUIREMENTS: Design and configuration: See figure 1. Force to engage and disengage: Longitudinal force: Not applicable. Torque: 2 inch

12、-pounds maximum. Coupling proof torque: Not applicable. Inspection conditions: Coupling torque: 4 to 6 inch-pounds. Mating characteristics: See figure 2 for dimensions. Center contact (female): Oversize test pin - .057 inch diameter minimum (nonclosed entry contacts only). Insertion depth - .125 inc

13、h minimum. Number of insertions 1. Insertion force test: Steel test pin diameter .054 inch minimum. Test pin finish: 16 microinches. Insertion force: 2 lbs maximum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/31C 4 Withdrawal force

14、test: Steel test pin diameter .052 inch maximum. Withdrawal force: 2 oz. minimum. Test pin finish: 16 microinches. Hermetic seal: Not applicable. Insulation resistance: Method 302 of MIL-STD-202, test condition B. 5,000 megohms minimum. Center contact retention: 6 lbs minimum axial force. 4 inch-oun

15、ces radial torque minimum. Corrosion (salt spray): Method 101, test condition B, MIL-STD-202. Voltage standing wave ratio (VSWR): Not applicable. Connector durability: 500 cycles at 12 cycles per minute maximum. The connector shall meet the mating characteristics and force to engage and disengage re

16、quirements. Contact resistance: In milliohms maximum. Contact Initial After environment Center contact Outer contact 1.5 .2 2.0 Not applicable Dielectric withstanding voltage: Method 302 of MIL-STD-202. 1,500 volts rms minimum at sea level. Vibration, high frequency: Method 204, test condition B, MI

17、L-STD-202. Shock: Method 213 of MIL-STD-202, test condition I. Thermal shock: Method 107 of MIL-STD-202, test condition B, except high temperature shall be +200C. Moisture resistance: Method 106 of MIL-STD-202. No measurements at high humidity. Insulation resistance shall be at least 200 megohms wit

18、hin 5 minutes after removal from humidity. Corona level: Voltage: 375 volts, minimum. Altitude: 70,000 feet. RF high potential withstanding voltage: Voltage and frequency: 1,000 volts rms at 5 MHz. Leakage current: Not applicable. Cable retention force: Not applicable. Coupling mechanism retention f

19、orce: Not applicable. RF leakage: Not applicable. Insertion loss: Not applicable. Group Qualification: See table II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-39012/31C 5 Part or Identifying Number (PIN): M39012/31- (dash number from ta

20、ble I). Changes from previous issues. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-PRF-39012, this document references the following: MIL-STD-202 ASME B107.100-2010 C

21、ONCLUDING MATERIAL Custodians: Preparing activity: Army CR DLA-CC Navy EC Air Force 85 DLA - CC Review activities: Army AM, AT, CR4, MI Navy AS, MC, OS, SH (Project 5935-2013-195) Air Force 19, 99 NASA - NA NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-