DLA MIL-J-87037 D-1988 JUMPER MAN-S WHITE《男式白色工作服》.pdf

《DLA MIL-J-87037 D-1988 JUMPER MAN-S WHITE《男式白色工作服》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-J-87037 D-1988 JUMPER MAN-S WHITE《男式白色工作服》.pdf（33页珍藏版）》请在麦多课文档分享上搜索。

1、* 2 a 0 O NIL-J-87037D 4 7797706 OqL0203 7 c 84- 05 MIL-J-87037D(NU) 8 June 1988 SUPERSEDING MIL-J-87037C(NU) 27 September 1983 MILITARY SPECIFICATION JUMPER, MANS, WHITE This specification is approved for use by the Navy Clothing and Textile Research Facility, Department of the Navy, and is availab

2、le for use by all Departments and Agencies of the Department of Defense. 1. SCOPE * 1.1 Scope. This specification covers the requirements for 100% polyester certified Navy twill white jumper. * 1.2 Classification. Jumpers covered by this specification shall be of one type only in the following sizes

3、 and lengths (see 6.2). Sizes - 30, 32, 34, 36, 38, 40, 42, 44, 46, 48, 50, 52 Lengths - Short, Regular, Long, and Extra Long - Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in .improving this document should be addressed to: Officer in Charge

4、, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization - Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A PSC 8405 *DISTRIBUTION STATEMENT A. Approved for public rel

5、ease, distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2, APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of t

6、his specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the DeDartment of Defense I Index of Specifications in the solicitation. SPECIFICATIONS FEDERAL V-B-871 V-T-280 NN-P-71 DDD-fi-20 DDD-T-86 MILITARY MIL-P-

7、15011 MIL-E-17757 MIL-T-43548 MIL-C-87052 STBARDS EEDERAL FED-STD-751 MILITAIRY MIL-STD-3.05 MIL-STD-I29 MIL-STD-147 and Standards (DODISS) and supplement thereto, cited - Button, Sewing Hole, and Button, Staple (Plastic) - Thread, Cotton, Gimp, Buttonhole - Pallet, Material Handling, Wood, Stringer

8、 - Label; For CLathing, Equipage, and Tentage (General - Tape, Textil, Cotton, General Purpose (Unbleached, Construction, 2 Way or 4 Way (Partial Use) Bleached, or Dyed) - Pallet , Material Handling, Wood, Post Construction, - Boxes, Shipping, Fiberboard (Modular Sizes) - Thread, Polyester Core: Cot

9、ton- , Rayon- , 4 Way Entry Poyes ter-Covered - Cloth, Twill, Polyester, Whie - Stitches, Seams, and Stitchings - Sampling Procedures and Tables for Inspection by - Marking for Shipment and Storage - Palletized Unit Loads Attributes (Copies of specifications, standards, drawings, and publications re

10、quired by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer . ) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-J-7037D 4 9 77777Ob Oq110205 2

11、H MIL-J-87037D(NU) * 2.1.2 Other Government documents, drawings, and publications. The followinn other Government documents, drawings, and Publications form a Part - of this specification to the extent speccfied herein. Unless otherbe specified, the issues shall be those in effect on the date of the

12、 solicitation. LAWS AND REGULATIONS US POSTAL SERVICE MANUAL (Copies may be obtained from the Superintendent of the Documents, U.S. Government Printing Office, Washington, DC 20402-0001.) 2.2 Other publications. The following document(s) form a part of this specification to the extent specified here

13、in. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issue of the nongovernment documents which is cu

14、rrent on the date of the solicitation. NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applications for copies should be addressed to the American Trucking Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404). UNIFORM C

15、LASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Applications for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, IL 60606-5808). THE COLOR ASSOCIATION OF THE UNITED STATES Department of Defense Standard Shades for Butt

16、ons Department of Defense Standard Shades for Sewing Threads (Application for copies of color cards should be addressed to the Color Association of the U.S., 343 Lexington Avenue, New York, NY 10016). NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC. AGENT NATIONAL MOTOR FREIGHT CLASSIFICATION (Appli

17、cation for copies should be addressed to American Trucking . Association, Attn: Traffic Department, 1616 P Street, NW, Washington, DC 20036-1404). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- I _- - - MIL-J-7037D 4 9999906 0430206 4 MIL-J-87037

18、D(NU) * 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemptio

19、n has been obtained. 3 REQUIREMENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in the sample in which case this specification shall govern. 3.2 First article. When specified, the contra

20、ctor shall furnish sample unit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Material, * 3.3.1 Basic material. The material for the jumper shall be a polyester twill cloth shade white 3006 conforming to MIL-C-87052. 3.3.2 Tape, cotton. The cotton tape for the hanger loops shall

21、 conform to type II, class 2, 1/2 inch width of DDD-T-86. 3.3.3 Thread. * 3.3.3.1 Thread, covered, polyester. The thread for seaming and stitching shall be cotton covered or rayon covered polyester, shade white AH, Cable No. 66050, Ticket No. 24, 50, and 70, 2 or 3 ply and for crowtack stitching Tic

22、ket No. 50, 2 or 3 ply conforming to MIL-T-43548. The Cable No. shall conform to the Department of Defense Standard Shades for Sewing Threads. The use of polyester-covered polyester core thread is not allowed. * 3.3.3.1.1 Automatic pocket machine. When an automatic pocket machine using a 101 stitch

23、type is used, the thread shall be type IC2, Ticket No. A, 3 ply conforming to V-T-276. When an automatic pocket machine using a 301 stitch type is used, the thread shall be Ticket No. 50, 2 or 3 ply conforming to MIL-T-43548. The Cable No. shall be as stated in 3.3.3.1. * 3.3.3.2 Colorfastness. The

24、thread shall show discoloration to light and laundering equal to or better than the standard sample when tested as specified in V-T-276 or MIL-T-43548. As a limit of acceptability or when no standard sample is available, the thread shall show a minimum of lgood“ discoloration to light and laundering

25、 when tested as specified in V-T-276 or MIL-T-43548. * 3.3.4 Button. The button for the inside swing pocket shall be 22-line and conform to type II, class D, style 19 of V-B-871. The color of the button shall be White, Shade BA, Cable No. 62031 in accordance with the Department .of Defense Standard

26、Shades for Buttons. * 3.3.5 Gimp cotton. The cotton gimp or reinforcing buttonholes shall be bleached white AH, Cable No. 66050 in accordance with the Department of Defense Standard Shades for Sewing Threads and shall conform to type I or II, size no. 8 of V-T-280. 4 Provided by IHSNot for ResaleNo

27、reproduction or networking permitted without license from IHS-,-,-HIL-J-87037D 4 7797706 0430207 b MIL-J-87037D(NU) * 3.3.5.1 Colorfastness. The gimp shall be equal to or better than the standard sample when tested for discoloration to laundering. As a limit of acceptability or when no standard samp

28、le is available, the gimp shall show a minimum rating of llgoodll when tested for discoloration to laundering as speciied in V-T-280. * 3.3.6 Combination label. Each jumper shall have a combination identification, personnel, and instruction label conforming to type VI, classes 10 and 15 of DDD-L-20.

29、 The printing shall show fastness to laundering and shall bear the following inscription and format: NAME: SERVICE NO: JUMPER, MANS, WHITE FIBER CONTENT: 100% POLYESTER NAME OF CONTRACTOR: . NAME OF MANUFACTURER: CONTRACT NO: DLA-100-00-0-0000 (EXAMPLE) (IF DIFFERENT THAN CONTRACTOR) MACHINE WASHING

30、 Machine wash. Permanent press cycle, hot wash. Do not mix colors. Fill machine with clothes to 2/3 capacity. Use heavy duty soap or detergent. Prespot stains with a laundry stain pretreatment. If needed, use a non-chlorine bleach. Tumble dry using a warm setting or shape and hang dry. Remove at onc

31、e from dryer. If touch-up ironing is needed, use a warm iron, press jumper inside-out. OR Follow NAVEDTRA Manual 414-01-45-81, Formula II. * 3.3.6.1 Size label. Each jumper shall have a size label conforming to type IV or VI, Class 2 of. DDD-L-20. The label shall be sufficiently sized to indicate si

32、ze, length, and stock number. The inscription shall be as follows : 34L (Example) Stock Number 8405-00-000-0000 (Example) NOTE: Abbreviation for the applicable size shall be S for Short, R for Regular, L for Long, and XL for Extra-Long. * 3.3.6.2 Removable size ticket. Each jumper shall have a comme

33、rcial type size ticket attached to the outside of the lower left sleeve. The ticket shall be 1-1/2 inches long and 2 inches high, made of a suitable plain white cardboard. The corners of the ticket may be double perforated for ease in tacking. The size (38R - Example) shall be printed or stamped on

34、the upper left hand corner in black or blue ink. The lettering for the size shall be 1/4 inch in height. Abbreviations for lengths shall be allowed-in accordance with 3.3.6.1. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_-p_ I-I-_ 3 - _ - .-_

35、MIL-J-7037D 4 W 7777706 0430208 MIL-J-87037D(NU) I 3.4 Desi n. The jumper shall be of the pull-over type having a one piece front an -+ a one piece back, a plain square sailor collar, a “V“ neck, one piece sleeves and finished at the bottom with turned-up hems. There shall be one beason type pocket

36、on the left front and one dummy (closed) beason type pocket on the right front which shall have an inside swing pocket and button flap closure (see figure 1 and 2). 3.4.1 Figures. The figures are furnished for information purposes only. To the extent of any inconsistencies between the specification

37、and the figure, the specification shall govern. * 3.5 Patterns. Standard patterns to be used to cut working patterns will be furnished by the Government (see 6.3). The working patterns shall be identical to the Government patterns. Neither the Government patterns nor the working patterns shall be al

38、tered in any way, except that additional notches for use during construction are permitted on the working patterns. Also, minor modifications are permitted where necessary when using automatic equipment. These modifications shall not alter the dimensional, serviceability, or appearance requirements

39、cited in the specification. The patterns allow a 1/2 inch seam allowance for double lapped and double stitched seams, or for safety-stitched, double needle topstitched seams. The component parts for the jumper shall be cut from in accordance with the following pattern parts: Ma terial Pattern parts

40、Cut parts Cloth, polyester twill Back Front Sleeve Topcollar Undercollar Inside pocket (right front) . Outside pocket (left front) Pocket welt a 3.6 Construction. * 3.6.1 Stitches, seams, and stitchings. Stitch, seams, and stitching types specified in Table I shall conform to FED-STD-751. Wherever t

41、wo or more methods for seam or stitch types are given for the same part of the operation, any one of them may be used. Where stitch type 401 is used, the looper (underthread) shall be on the inside of the jumper. Unless otherwise specified, double needle stitching shall be 1/4 (+ 1/16) inch gauge wi

42、th the outer row of stitching 1/16 to 1/8 inch from the Finished edge. Topstitching and edge stitching shall be 1/16 to 1/8 inch from edge, unless otherwise specified in Table I. Seam allowances shall be maintained with seams sewn so that no raw edges, runoffs, twists, pleats, or puckers or open sea

43、ms result. All seams shall start and finish evenly. Thread tension shall be maintaned so that there is no tight or loose stitching. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* 3.6.2 Thread breaks and ends of seams. Ends of all seams and stitc

44、hings when not caught in other seams or stitchings shall be backtacked not less than 3/8 inch. The ends of a continuous line of stitching (except labels) shall be overlapped not less than 1/2 inch. The ends of label stitching shall be overlapped not less than 3 stitches. Thread breaks (all stitch ty

45、pes) shall be secured by stitching back of the break not less than 1/2 inch. Skipped stitches or 401 stitch type thread breaks may be repaired by using 301 stitch type. When stitch type 401 is permitted as an option, it shall not be used unless the ends are caught in other seams or stitching. As an

46、exception, when closing the sides of the pockets, stitch type 401 may be used and a 1/4 to 3/8 inch chain shall extend beyond the ends not caught in other stitching. During the overedgc operations, a knife shall be used for trimming off only the loose thread ends. The bight of the overedge stitching

47、 shall be 3/16 inch. 3-6.3 Stitches per inch. The minimum and maximum number of stitches per inch shall be as specified in Table I. * 3.7 Manufacturing operations requirements. The jumper shall be manufactured in accordance with the operation requirements specified in Table I. The contractor is not

48、required to follow the exact sequence of operations as listed, provided the finished jumper is identical to that produced by following the sequence of operations as listed in Table I. Minor modifications are permitted where necessary when using automatic equipment. These modifications shall not alte

49、r the dimensional, serviceability, or appearance requirements cited in the specification. 3.7.1 Shade and size marking. The component parts of the jumper shall be marked or ticketed to insure-a uniform shade and size throughout the garment. - Any method may be used except: (1) Corrosive metal fastening devices (2) Sew-on shade tickets (3) Adhesive type tickets which discolor or adhere to the material upon removal of the tickets NOTE: The