DLA MIL-DTL-15370 16 C-2008 COUPLERS DIRECTIONAL (COAXIAL SMA CONNECTORS) (2 TO 1000 MHZ).pdf

《DLA MIL-DTL-15370 16 C-2008 COUPLERS DIRECTIONAL (COAXIAL SMA CONNECTORS) (2 TO 1000 MHZ).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-15370 16 C-2008 COUPLERS DIRECTIONAL (COAXIAL SMA CONNECTORS) (2 TO 1000 MHZ).pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5985 MIL-DTL-15370/16C 7 May 2008 SUPERSEDING MIL-DTL-15370/16B 18 June 2003 DETAIL SPECIFICATION SHEET COUPLERS, DIRECTIONAL, (COAXIAL, SMA CONNECTORS) (2 TO 1000 MHz) This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The requirement

2、s for acquiring the couplers described herein shall consist of this specification sheet and MIL-DTL-15370. Inches mm Inches mm Inches mm .01 0.3 .10 2.5 .42 10.7 .02 0.5 .16 4.1 .50 12.7 .03 0.8 .19 4.8 .56 14.2 .04 1.0 .25 6.4 1.00 25.4 .05 1.3 .29 7.4 1.25 31.8 .06 1.5 .38 9.7 1.62 41.1 2.00 50.8

3、NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. FIGURE 1. Dimensions and configuration for part numbers M15370/16-001 M15370/16-008 through M15370/16-015, M15370/16-017, M15370/16-018, and M15370/16-020 through M15370/16-022. INCH-POUND Provided by IHSNot fo

4、r ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/16C 2 Inches mm .005 0.13 .020 0.51 .145 3.68 .250 6.35 .30 7.6 .32 8.13 .37 9.4 .42 10.7 .50 12.7 .875 22.22 1.40 35.6 4.40 111.8 4.90 124.5 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given

5、 for information only. 3. Unless otherwise specified, tolerance is .03 (0.8 mm). FIGURE 2. Dimensions and configuration for part number M15370/16-002. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/16C 3 Inches mm .031 0.79 .125 3.18 .

6、300 7.62 .400 10.16 .485 12.32 .570 14.48 .875 22.22 1.000 25.40 1.750 44.45 3.188 80.98 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerance is .16 (0.41 mm). FIGURE 3. Dimensions and configuration for part number M15370/

7、16-003. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/16C 4 Inches mm Inches mm .002 0.05 .31 7.9 .010 0.25 .350 8.89 .03 0.8 .375 9.52 .05 1.3 .50 12.7 .112 2.84 .75 19.0 .12 3.05 1.500 38.10 .125 3.18 2.00 50.8 .25 6.5 3.50 88.9 .30

8、0 7.62 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerance is .02 (0.5 mm). FIGURE 4. Dimensions and configuration for part numbers M15370/16-004 through M15370/16-007. Provided by IHSNot for ResaleNo reproduction or netw

9、orking permitted without license from IHS-,-,-MIL-DTL-15370/16C 5 Inches mm .030 0.76 .04 1.02 .12 3.05 .133 3.38 .139 3.53 .25 6.35 .31 7.87 .36 9.14 .50 12.70 .70 17.78 1.250 31.75 1.43 36.32 1.50 38.10 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Un

10、less otherwise specified, tolerance is .03 (0.8 mm). FIGURE 5. Dimensions and configuration for part numbers M15370/16-016 M15370/16-019, and M15370/16-023. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Electrical characteristics. Coupling

11、 (dB) VSWR max RF input power to primary Dash number Frequency range (MHz) Nominal Tolerance Coupling variation (dB) max Effective directivity (dB) min Insertion loss (dB) max Primary line Secondary line Over frequency range (watts) Avg (W) Peak (KW) 001N S 25 - 35 25 1.0 1.0 25 0.25 1.20:1 1.20:1 5

12、 5 - 002N S 125 - 250 30 1.0 0.75 15 0.30 1.15:1 1.15:1 50 50 - 003N S 125 - 250 10 1.25 0.75 25 0.20 1.10:1 1.10:1 50 50 3 004N S 250 - 500 6 0.5 0.5 25 0.10 1.10:1 1.25:1 100 100 6 005N S 250 - 500 10 0.75 0.75 25 0.10 1.10:1 1.25:1 100 100 6 006N S 250 - 500 20 1.0 1.0 25 0.10 1.10:1 1.25:1 100 1

13、00 5 007N S 250 - 500 30 1.0 1.0 25 0.10 1.10:1 1.25:1 100 100 6 008N S 285 - 315 25 1.0 1.0 25 0.25 1.20:1 1.20:1 5 5 - 009N S 20 - 60 15 1.0 0.5 30 0.5 1.30:1 1.30:1 5 5 - 010N S 68 - 82 30 1.0 0.5 30 0.5 1.30:1 1.30:1 5 5 - 011N S 102 - 138 30 1.0 1.0 25 0.25 1.20:1 1.20:1 5 5 - 012N S 2 - 100 10

14、 1.0 0.5 30 0.5 1.30:1 1.30:1 5 5 - 013N S 2 - 100 15 1.0 0.5 30 0.5 1.30:1 1.30:1 5 5 - 014N S 2 - 100 20 1.0 0.5 30 0.5 1.30:1 1.30:1 5 5 - 015N S 270 - 330 20 +0.6 -0.0 0.2 40 0.6 1.30:1 1.30:1 5 5 - 016N S 420 - 450 16 0.3 0.25 25 0.35 1.15:1 1.20:1 10 10 - 017N S 50 - 500 10 1.0 0.5 25 0.5 1.30

15、:1 1.30:1 5 5 - 018N S 10 - 500 15 1.0 0.5 25 0.5 1.20:1 1.30:1 5 5 - 019N S 10 - 500 15 0.25 0.25 25 0.35 1.20:1 1.20:1 10 10 - 020N S 50 - 400 10 1.0 0.5 25 0.5 1.30:1 1.30:1 5 5 - 021N S 100 - 500 20 1.0 0.5 25 0.5 1.30:1 1.30:1 5 5 - 022N S 10 - 1000 20 1.0 0.5 25 0.6 1.30:1 1.30:1 5 5 - 023N S

16、75 - 1000 10 0.5 0.5 25 0.6 1.30:1 1.30:1 2 2 - 6 MIL-DTL-15370/16C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/16C 7 TABLE II. Physical and environmental characteristics. Dash number Weight (average) Temperature range (operating on

17、 top non-operating on bottom) Shock (specified pulse) (method 213) 1/ (oz) 001 0.9 -54C to +75C -62C to +75C H 002 4.5 -55C to +85C -55C to +85C C 003 6.5 0C to +50C -62C to +75C H 004 5.0 -55C to +85C -55C to +85C N/A 005 5.0 -55C to +85C -55C to +85C N/A 006 5.0 -55C to +85C -55C to +85C N/A 007 5

18、.0 -55C to +85C -55C to +85C N/A 008 0.9 -54C to +75C -62C to +75C H 009 1.5 -55C to +105C -55C to +125C H 010 1.5 -55C to +105C -55C to +105C H 011 1.5 -55C to +105C -55C to +125C H 012 1.5 -55C to +105C -55C to +125C H 013 1.5 -55C to +105C -55C to +125C H 014 1.5 -55C to +105C -55C to +125C H 015

19、 1.5 -55C to +105C -55C to +125C H 016 1.5 -54C to +100C -55C to +125C H 017 1.5 -55C to +105C -55C to +125C H 018 1.5 -55C to +105C -55C to +125C H 019 1.5 -54C to +100C -55C to +125C H 020 1.5 -55C to +105C -55C to +125C H 021 1.5 -55C to +105C -55C to +100C H 022 1.5 -55C to +105C -55C to +125C H

20、 023 1.5 -55C to +100C -55C to +125C H 1/ Letters denote test conditions of MIL-STD-202. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-15370/16C 8 REQUIREMENTS: Design, construction and physical dimensions: See figures 1 through 5. Operatin

21、g temperature range: See table II. Weight: See table II. Shock (specified pulse): See table II. Electrical: See table I. Marking: Part number (see tables I and II) shall be located as shown on figures 1 through 5. Part number: M15370/16- (and a dash number from table I). Referenced Documents: In add

22、ition to MIL-DTL-15370, this document references the following: MIL-PRF-39012/55 MIL-STD-202 Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Forc

23、e - 11 DLA - CC Review activities: (Project 5985-2008-033) Army - MI Navy - AS, CG, MC, OS, SH Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-