DLA DSCC-DWG-89032 REV D-2001 CONNECTOR ELECTRICAL RECEPTACLE RADIO FREQUENCY SERIES TNC SOCKET CONTACT FOR M17 152-00001 CABLE《系列TNC插孔接触件射频插座连接器 用于 M17 152-00001电缆》.pdf

《DLA DSCC-DWG-89032 REV D-2001 CONNECTOR ELECTRICAL RECEPTACLE RADIO FREQUENCY SERIES TNC SOCKET CONTACT FOR M17 152-00001 CABLE《系列TNC插孔接触件射频插座连接器 用于 M17 152-00001电缆》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-89032 REV D-2001 CONNECTOR ELECTRICAL RECEPTACLE RADIO FREQUENCY SERIES TNC SOCKET CONTACT FOR M17 152-00001 CABLE《系列TNC插孔接触件射频插座连接器 用于 M17 152-00001电缆》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONSLTR DESCRIPTION DATE APPROVEDA Add source 00795. Format changes. 27 Mar 1990 CottongimB Incorporate NOR. 9 Nov 1992 Charles KoellerC Incorporate NOR. 2 Aug 1993 Randy LarsonD Part number and source update. Editorial changes throughout. 14 June 2001 Robert HeberPrepared in accordance with MI

2、L-STD-100REVPAGEREVDDDDDDREV STATUSOF PAGES PAGE 123456PREPARED BYPMIC N/ARon GaryDEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OHIO 43216-5000CHECKED BY TITLEC. W. KoellerAPPROVED BYRichard MarbaisCONNECTOR, ELECTRICAL, RECEPTACLE, RADIOFREQUENCY, SERIES TNC, SOCKET CONTACT, FORM17/152-00001 CABLESIZE C

3、AGE CODE037Z3DWG. NO.89032Original date ofdrawing12 July 1989AREV D PAGE 1 OF 6AMSC N/A 5935-E641-09DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.

4、037Z3 89032DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVDPAGE2NOTES:1. A polyolefin sleeve in accordance with MIL-I-23053/5 shall be supplied with each part.2. Dimensions are in inches.3. Metric equivalents are given for general information only.4. Metric equivalents are in parentheses.

5、5. Dimension .812 is the largest overall diameter of the connector.6. Wrench flats to accommodate standard wrench opening in accordance with FED-STD-H28, appendix 10.7. All undimensioned pictorial configurations are for reference purposes only.8. Dimension 1.625 maximum defines the overall length of

6、 the connector when assembled to the cable.9. No special tools shall be required for assembly to cables.10. Assembly of these connectors shall be in accordance with MIL-PRF-39012, category C. The shield terminationshall be accomplished using the M22520/5-01 basic crimp tool with die M22520/5-37, clo

7、sure B. The centercontact shall be soldered.11. TNC socket contact interface in accordance with MIL-STD-348.12. Gasket material shall be Viton A or equivalent (Viton A is a brand name of E.I. DuPont).FIGURE 1. General configuration.Provided by IHSNot for ResaleNo reproduction or networking permitted

8、 without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89032DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVDPAGE3Inches mm.010.156.343.437.5930.253.968.7111.1015.06NOTES:1. Dimensions are in inches.2. Metric equivalents are given for general information only.FIGURE 2. Cable strip dimens

9、ions.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89032DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVDPAGE4ENGINEERING DATA:Nominal impedance: 50 ohms.Frequency range: DC to 11 GHz.Voltage rating: 500 volts r

10、ms maximum at sea level;125 volts rms at 70,000 feet.Operating temperature: -65C to +165C.REQUIREMENTS: (The requirements of DSCC drawing 84148 are applicable.)Dimensions and configurations: See figure 1 herein and MIL-STD-348.Force to engage and disengage: 2 inch-pounds maximum torque (.225 Nm).Cou

11、pling proof torque: 15 inch-pounds minimum (1.69 Nm).Hermetic seal: Not applicable.Leakage: Not applicable.Center contact retention: 6 pounds minimum axial force (26.69 N).Voltage standing wave ratio (VSWR): The VSWR, when measured in accordance with MIL-PRF-39012 over afrequency range of 500 MHz to

12、 11 GHz, or approximately 80 percent of the cables upper cutoff frequency, whicheveris lower, shall not exceed 1.30:1 when measured at 50 ohms.Moisture resistance: Method 106 of MIL-STD-202, except no measurement at high humidity. Insulation resistanceshall be at least 200 megohms within 5 minutes a

13、fter removal from humidity chamber.Altitude: The connector shall operate as specified herein at altitudes up to and including 70,000 feet (21.336 km).Insulation resistance: Methods 302, test condition B of MIL-STD-202, 5,000 megohms, minimum.Connector durability: 500 cycles minimum, at 12 cycles per

14、 minute, maximum. The connector shall meet the matingcharacteristics and force to engage and disengage requirements.Dielectric withstanding voltage: 1,500 V rms, in accordance with method 301 of MIL-STD-202, minimum at sea level.Random vibration: Method 2005, test condition V, test level F of MIL-ST

15、D-1344.Salt spray: Method 101, test condition B of MIL-STD-202.Thermal shock: MIL-STD-202, test condition B of method 107 except test high temperature shall be +200C.Vibration, high frequency: MIL-STD-202, method 204, test condition B.Shock: MIL-STD-202, test condition I of method 213.Provided by IH

16、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89032DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVDPAGE5Contact resistance (In milliohms, maximum):Initial After environmentalCenter contact: 1.5 1.5Outer contact: 0.2 0.2Outer

17、 cable braid to body: 0.1 N/ACorona level: 375 V rms, at 70,000 feet (21.336 km).RF high potential withstanding voltage: 1,000 V rms, minimum.Frequency: 5 to 7.5 MHz.Leakage current: Not applicable.Coupling mechanism retention force: 100 pounds, minimum (444.8 N).RF leakage: -60 dB, minimum tested b

18、etween 2 and 3 GHz.RF insertion loss: 0.06 F(GHz) dB maximum from 3 to 6 GHzCable accommodation: M17/152-00001.Cable retention force: 10 pounds, minimum axial force (44.5 N).Part of Identifying Number (PIN): 89032TBS.Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

19、e from IHS-,-,-SIZECAGE CODE DWG NO.037Z3 89032DEFENSE SUPPLY CENTER, COLUMBUSCOLUMBUS, OH 43216-5000AREVDPAGE6Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as theybecome available. The vendors listed herein have agreed to this drawing and

20、 a certificate of compliance has beensubmitted to DSCC-VAI.DSCC drawingPIN1/VendorCAGENumberVendorreferencePIN89032TBS 007952493194375950771219100A59100024JS169-1925-T3908B-75M14113-00321/ Parts must be purchased to this DSCC PIN to assure thatall performance requirements and tests are met.Vender CA

21、GE Vendor namenumber and address00795 Delta Electronics416 Cabot StreetBeverly, MA 0191524931 Specialty Connector Co.2100 Earlywood DriveFranklin, IN 4613194375 Automatic Connector Inc.400 Moreland RoadCommaok, NY 1172595077 Solitron/Vector Microwave Products3301 Electronics WayWest Palm Beach, FL 33407Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-