DLA DSCC-DWG-89004 REV B-2007 RESISTOR-CAPACITOR NETWORK 16-PIN DIP《16插针 DIP 阻容网络》.pdf

《DLA DSCC-DWG-89004 REV B-2007 RESISTOR-CAPACITOR NETWORK 16-PIN DIP《16插针 DIP 阻容网络》.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-89004 REV B-2007 RESISTOR-CAPACITOR NETWORK 16-PIN DIP《16插针 DIP 阻容网络》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LT DESCRIPTION DATE APPROVED A Revise to present DoD policy requirements; remove source of supply. Editorial corrections throughout. 27 JUL 2000 Kendall A. Cottongim B Add pure tin prohibition paragraph. Editorial changes throughout. 14 FEB 2007 Michael Radecki CURRENT DESIGN ACTIVITY CAG

2、E CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.100 Selected item drawing REV STATUS OF PAGES REV B B B B B B B B B B PAGES 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Allan R. Knox DESIGN ACTIVITY: DEFENSE ELECTRONIC

3、 SUPPLY CENTER DAYTON, OHIO 45444-5000 Original date of drawing 17 AUG 89 CHECKED BY David E. Moore TITLE RESISTOR-CAPACITOR NETWORK, 16-PIN DIP APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 89004 REV B PAGE 1 OF 10 AMSC N/A 5905-E605 Provided by IHSNot for ResaleNo reproduction or

4、 networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89004 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the general requirements for a 16 pin, dual in-line package (DIP), resistor-capacitor network. 1.2 Part o

5、r Identifying Number (PIN). The complete PIN is as follows: 89004 - M 5100 G K Drawing number Characteristic (3.3.1.3) Resistance (3.3.1.1) Resistance Tolerance (3.3.1.2) Schematic (3.3.1.6) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The followi

6、ng specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-83401 - Resistor Networks, Fixed, Film, and

7、Capacitor-Resistor Networks, Ceramic Capacitor and Fixed Film Resistors, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Methods for Electronic and Electrical component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are avai

8、lable online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references

9、 cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-83401 an

10、d as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-83401 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SU

11、PPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89004 REV B PAGE 3 Inch mm Inch mm .0035 0.089 .055 1.40 .004 0.10 .065 1.65 .010 0.25 .085 2.16 .012 0.30 .100 2.54 .015 0.38 .135 3.43 .0185 0.470 .200 5.08 .020 0.51 .270 6.86 .030 0.76 .300 7.62 .035 0.89 .310 7.87 .045 1.14 .350 8.89

12、.046 1.17 .830 21.08 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .005 (0.13 mm). 4. The pictorial view of the style above is given as representative of the envelope of the item. Slight deviations from t

13、he outline shown, which are contained within the envelope, and do not alter the functional aspects of the devices are acceptable. 5. Pin 1 locator shall be a dot, notch, or numeral 1 adjacent to pin No. 1, in the shaded area. 6. Terminal centerline to centerline measurements made at point of emergen

14、ce of the lead from the body. 7. Measurement made at point of emergence of the lead from the body. FIGURE 1. Resistor network, 16-pin DIP. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT

15、 NO. 14933 DWG NO. 89004 REV B PAGE 4 3.3 Electrical characteristics. 3.3.1 Resistor requirements. 3.3.1.1 Resistance. Resistance values available shall be in accordance with MIL-PRF-83401 and herein (see table I). 3.3.1.2 Resistance tolerance. Unless otherwise specified (see table I) resistors are

16、available in resistance tolerances of 1 percent (F), 2 percent (G), and 5 percent (J). TABLE I. Resistance and capacitive values. PIN 89004- Resistance (ohms) Capacitance Microfarads) Schematic K *5100*K 1/ 510 0.01 Schematic M *49R9*M 1/ *68R0*M 1/ *75R0*M 1/ *1000*M 1/ 49.9 68 75 100 0.01 0.01 0.0

17、1 0.01 Schematic N *A001*N 1/ RS RE 39 5% 500 2% 0.01 1/ Asterisks in the PIN shall be coded to represent resistance tolerances and resistance characteristic allowed herein (see 1.2, 3.3.1.2, and 3.3.1.3) 3.3.1.3 Resistance temperature characteristics. The resistance temperature characteristics avai

18、lable shall be characteristic K and characteristic M in accordance with MIL-PRF-83401 and herein (see table I). 3.3.1.4 Power rating. The power rating shall be 0.1 watt for each resistor. The total network power rating shall be 1.2 watts. 3.3.1.5 Voltage rating. The maximum continuous working voltag

19、e for each resistor shall not exceed 100 volts dc or ac rms. 3.3.1.6 Schematic. The schematic of the resistor-capacitor network shall be identified by a single letter in accordance with MIL-PRF-83401 and herein (see figure 2). 3.3.2 Capacitor requirements. 3.3.2.1 Capacitance. When tested as specifi

20、ed in 4.3, the capacitance value shall be 0.01 F, within tolerance. 3.3.2.2 Capacitance tolerance. Capacitors are available in capacitance tolerance of 20 percent (M). 3.3.2.3 Dissipation factor. When tested as specified in 4.3.1, the dissipation factor shall not exceed 2.5 percent. 3.3.2.4 Voltage

21、rating. The voltage rating shall be 25 volts dc. 3.3.2.5 Dielectric withstanding voltage. When tested as specified in 4.3.2, there shall be no evidence of mechanical damage, arcing, or breakdown. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENS

22、E ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89004 REV B PAGE 5 FIGURE 2. Schematics. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 890

23、04 REV B PAGE 6 3.3.2.6 Insulation resistance. When tested as specified in 4.3.3, the insulation resistance of the capacitor shall be not less than 100,000 megohms unless otherwise specified. a. Pre-assembly: The insulation resistance of the internal capacitor prior to assembly in the network shall

24、be in accordance with the following requirements: 1. 25C - not less than 10,000 megohms or 100 megohm-microfarads, whichever is less. 2. 125C - not less than 5,00 megohms or 50 megohm-microfarads, whichever is less. b. Post assembly: The insulation resistance of the internal capacitor after assembly

25、 in the network shall be in accordance with the following requirements, when networks are tested in accordance with MIL-PRF-83401. 1. 25C - not less than 10,000 megohms or 100 megohm-microfarads, whichever is less. 2. 125C - not less than 5,000 megohms or 50 megohm-microfarads, whichever is less. 3.

26、3.2.7 Capacitance-temperature characteristic. When tested as specified in 4.3.4, the capacitance change shall not exceed 15 percent at -55C and +125C when tested with minimum voltage and +15 percent, -25 percent at -55C and +125C when tested at rated voltage. 3.4 Network requirements. When tested as

27、 specified in MIL-PRF-83401 and herein, and unless otherwise specified, the networks shall meet the respective requirements of MIL-PRF-83401 and the following: C shall not exceed 10 percent. DF shall not exceed 2.5 percent. 3.4.1 Thermal shock. When tested as specified in 4.4, networks shall meet th

28、e requirements of 3.4. 3.4.2 Power conditioning. When tested as specified in 4.5, networks shall meet the requirements of 3.4. 3.4.3 Network dielectric withstanding voltage. Networks shall be tested as specified and meet the requirements of MIL-PRF-83401. 3.4.4 Network insulation resistance. Network

29、s shall be tested as specified and meet the requirements of MIL-PRF-83401. 3.4.5 Short-time overload. When tested as specified in 4.6, networks shall meet the requirements of 3.4. 3.4.6 Solderability. Networks shall be tested as specified and meet the requirements of MIL-PRF-83401. 3.4.7 Resistance

30、to solvents. Networks shall be tested as specified and meet the requirements of MIL-PRF-83401. 3.5 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin sha

31、ll be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.6 Marking. Marking shall be in accordance with MIL-STD-1285 except the networks shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes.

32、 3.7 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageo

33、us life cycle costs. 3.8 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.9 Workmanship. Resistors shall be uniform in quality and free from defects that will affect life, serviceability, or appearance. Provi

34、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 89004 REV B PAGE 7 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not applicable to this document.

35、 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B inspections specified in table II and table III herein. 4.2.2 Group A inspection. Group A inspection shall consist of the inspections specified in table II,

36、and shall be made on the same set of sample units, in the order shown. TABLE II. Group A inspection. Inspection Requirement paragraph Test methodparagraph Number of samples Subgroup 1 Thermal shock Power conditioning Resistance Capacitance Dissipation factor 3.4.1 3.4.2 3.3.1.1 3.3.2.1 3.3.2.3 4.4 4

37、.5 1/ 4.3 4.3.1 100 percent inspection Subgroup 2 Visual and mechanical Inspection 3.1, 3.2, 1/ 3.6, and 3.9 1/ 13 1/ See MIL-PRF-83401 4.2.2.1 Subgroup 1 tests. Subgroup 1 tests shall be performed on a production lot basis on 100 percent of the product supplied under this drawing. Networks that are

38、 out of resistance or capacitance tolerance, or which experience a change in resistance or capacitance greater than that permitted for the tests of this subgroup shall be removed from the lot. Only lots having not more than three percent rejects or one network, whichever is greater due to exceeding

39、the specified resistance/capacitance change limit, as a result of subgroup 1 tests shall be furnished on orders. Corrective action shall be taken on such units and new pieces furnished. 4.2.2.2 Subgroup 2 tests. Statistical sampling inspection shall be performed on an inspection lot basis. A sample

40、of 13 parts shall then be randomly selected. If one or more defects are found, the lot shall be rescreened and defects removed. A new sample of 13 parts shall then be randomly selected. If one or more defects are found in this second sample, the lot shall be rejected and shall not be supplied to thi

41、s drawing. 4.2.3 Group B inspection. Group B inspection shall consist of the examinations and tests specified in table III, in the order shown. They shall be performed on samples from lots which have been subjected to and passed the group A inspection. 4.2.3.1 Certification. The acquiring activity,

42、at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2d). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14

43、933 DWG NO. 89004 REV B PAGE 8 TABLE III. Group B inspection. Inspection Requirement paragraph Test method paragraph Number of samples Number offailures allowed Subgroup 1 Resistance temperature characteristic Capacitance temperature characteristic Dielectric withstanding voltage (network) Dielectri

44、c withstanding voltage (capacitor) Insulation resistance (network) Insulation resistance (capacitor) Short-time overload 3.3.1.3 3.3.2.7 3.4.3 3.3.2.5 3.4.4 3.3.2.6 3.4.5 1/ 4.3.4 1/ 4.3.2 1/ 4.3.3 4.6 13 0 Subgroup 2 Solderability Resistance to solvents 3.4.6 3.4.7 1/ 1/ 6 8 0 1/ See MIL-PRF-83401

45、4.2.3.2 Subgroup 1. A sample of 13 parts shall be randomly selected. If one or more defects are found, the lot shall be rescreened and defects removed. If one or more defects are found a new sample of 13 parts shall then be randomly selected. If one or more defects are found in the second sample, th

46、e lot shall be rejected and shall not be supplied to this drawing. 4.2.3.3 Subgroup 2. A sample consisting of 14 parts shall be randomly selected, 6 samples subjected to the solderability test and 8 parts to the resistance to solvents test. If one or more defects are found, the lot shall be rescreen

47、ed and defects removed. A new sample of 14 parts shall then be randomly selected. If one or more defects are found in the second sample, the lot shall be rejected and shall not be supplied to this drawing. 4.3 Capacitance (see 3.3.2) Capacitors shall be tested in accordance with method 305 of MIL-ST

48、D-202. The following details and exceptions shall apply: a. Test frequency: 1 kHz 100 Hz. b. Test voltage: 1.0 volt 0.2 volts rms. 4.3.1 Dissipation factor (see 3.3.2.3) The dissipation factor shall be measured with a capacitance bridge or other suitable method at a frequency of 1 kHz 100 Hz and a v

49、oltage of 1.0 0.2 volts rms. The inherent accuracy of the measurement shall be 2 percent of the reading +0.1 percent dissipation factor (absolute). 4.3.2 Dielectric withstanding voltage (capacitor) (see 3.3.2.5). The capacitor shall be tested in accordance with method 301 of MIL-STD-202. A voltage of 2.5 times the rated voltage shall be a