DLA DSCC-DWG-86099 REV E-2012 CONNECTORS ELECTRICAL UNSHROUDED HEADERS PWB TERMINATION 025 DOUBLE ROW STRAIGHT THRU.pdf

《DLA DSCC-DWG-86099 REV E-2012 CONNECTORS ELECTRICAL UNSHROUDED HEADERS PWB TERMINATION 025 DOUBLE ROW STRAIGHT THRU.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-86099 REV E-2012 CONNECTORS ELECTRICAL UNSHROUDED HEADERS PWB TERMINATION 025 DOUBLE ROW STRAIGHT THRU.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Page 2, add tolerance to dimension C. Page 3, change dimension C on dash 14. Add additional pin length configurations. Page 6, add vendor CAGE numbers OAKZ5 and 95238. 1/19/88 Richard Marbais B Change marking requirement. Change current rating. Add caution n

2、ote. Dimensional changes to figure 1. Inactive for new design as of date of rev B. 5/15/90 Richard Marbais C Change CAGE 14933 to 037Z3. Added wrappost geometry requirements. Update material call-outs. 04/18/02 Robert Heber D Updated source CAGE OAKZ5 manufactures name and location address. Editoria

3、l changes throughout. 6 June 2011 Howard Jenkins E Add option for selective plating to plating code “A”. 17 October 2012 Abdo Abdouni Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV STATUS OF PAGES REV E D D E D D D D D PAGE 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY DEFENSE

4、 SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43216-5000 Gail Willis Original date of drawing 7 Nov 1986 CHECKED BY TITLE Carl Dello-Stritto CONNECTORS, ELECTRICAL, UNSHROUDED HEADERS, PWB TERMINATION, .025, DOUBLE ROW, STRAIGHT THRU APPROVED BY Richard Marbais SIZE CAGE CODE DWG. NO. 86099 A 037Z3 REV E

5、PAGE 1 OF 9 AMSC N/A 5935-E845-001 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES: DLA LAND AND MARITIME COLUMBUS, OH 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE C

6、AGE CODE DWG NO. A 037Z3 86099 REV D PAGE 2 Inches mm .008 .010 .015 .045 .050 .100 .190 0.20 0.25 0.38 1.14 1.27 2.54 4.83 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified all tolerances are .005 (0.13 mm). FIGURE 1. Dim

7、ensions and configuration.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE CAGE CODE DWG NO. A 037Z3 86099 REV D PAGE 3 TABLE I. Pin length. 1/ 2/ 3/ Dash number Dimension A Length above pla

8、stic Dimension B Length below plastic Dimension C Overall length 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 .200 .230 .230 .230 .230 .230 .230 .230 .230 .230 .230 .255 .285 .285 .318 .318 .318 .318 .318 .318 .318 .318 .318 .400 .400 .430 .500 .520 .540

9、.610 (5.08) (5.84) (5.84) (5.84) (5.84) (5.84) (5.84) (5.84) (5.84) (5.84) (5.84) (6.48) (7.24) (7.24) (8.08) (8.08) (8.08) (8.08) (8.08) (8.08) (8.08) (8.08) (8.08) (10.16) (10.16) (10.92) (12.70) (13.21) (13.72) (15.49) .110 .045 .095 .100 .110 .150 .120 .156 .225 .285 .595 .120 .095 .230 .107 .11

10、5 .120 .130 .220 .318 .410 .420 .520 .115 .120 .120 .120 .318 .120 .115 (2.79) (1.14) (2.41) (2.54) (2.79) (3.81) (3.05) (3.96) (5.72) (7.24) (15.11) (3.05) (2.41) (5.84) (2.72) (2.92) (3.05) (3.30) (5.59) (8.08) (10.41) (10.67) (13.21) (2.92) (3.05) (3.05) (3.05) (8.08) (3.05) (2.92) .410 .375 .425

11、 .430 .440 .480 .450 .486 .555 .615 .925 .475 .480 .615 .525 .533 .538 .548 .638 .736 .828 .838 .983 .615 .620 .650 .720 .938 .760 .825 (10.41) (9.53) (10.80) (10.92) (11.18) (12.19) (11.43) (12.34) (14.10) (15.62) (23.50) (12.07) (12.19) (15.62) (13.34) (13.54) (13.67) (13.92) (16.21) (18.69) (21.0

12、3) (21.29) (24.97) (15.62) (15.75) (16.51) (18.29) (23.83) (19.30) (20.96) 1/ Dimensions are in inches. 2/ Metric equivalents are given for general information. 3/ Metric equivalents are in parentheses. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

13、-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE CAGE CODE DWG NO. A 037Z3 86099 REV E PAGE 4 TABLE II. Plating. Plating Contact area “A” Termination area “B” A 1/ Gold Gold B Tin-lead plated Tin-lead plated D Gold Tin dipped 2/ E Tin-lead plated Solder dipped 1/ Selective gold plating

14、applicable to contact pin lengths .230 inch (5.84 mm) and longer. Measured from tip of contact pin, remainder of contact post to be plated with nickel in accordance with SAE-AMS-QQ-N-290, class 2, 50 microinch (1.27 m) minimum. 2/ The use of pure tin is prohibited. Tin content used in connector mate

15、rials shall not exceed 97 percent, and an alloy material shall be chosen to inhibit the growth of tin whiskers. TABLE III. Dimensions D. 1/ 2/ 3/ Number of positions Dimensions Number of positions Dimensions 02 04 06 08 10 12 14 16 18 20 22 24 26 28 30 32 34 36 .100 .200 .300 .400 .500 .600 .700 .80

16、0 .900 1.000 1.100 1.200 1.300 1.400 1.500 1.600 1.700 1.800 (2.54) (5.08) (7.62) (10.16) (12.70) (15.24) (17.78) (20.32) (22.86) (25.40) (27.94) (30.48) (33.02) (35.56) (38.10) (40.64) (43.18) (45.72) 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 1.900 2.000 2.100 2.200 2.300 2.400 2.500 2.

17、600 2.700 2.800 2.900 3.000 3.100 3.200 3.300 3.400 3.500 3.600 (48.26) (50.80) (53.34) (55.88) (58.42) (60.96) (63.50) (66.04) (68.58) (71.12) (73.66) (76.20) (78.74) (81.28) (83.82) (86.36) (88.90) (91.44) 1/ Dimensions are in inches. 2/ Metric equivalents are given for general information. 3/ Met

18、ric equivalents are in parentheses. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE CAGE CODE DWG NO. A 037Z3 86099 REV D PAGE 5 REQUIREMENTS: Shall meet the requirements of drawing 86100,

19、except as specified herein. Dimensions and configuration: See figure 1 and tables I, II, III. Temperature range: -40C to +105C. Dielectric withstanding voltage: 1,000 volts rms (sea level). Current rating: 3 amperes continuous to 5 amperes maximum. Insulation resistance: 5,000 megohms. Pin retention

20、: 2 pounds (0.91 kg) minimum either direction. Materials: Contact: Three-fourth hard phosphor bronze in accordance with ASTM B139/B139M. Contact plating: Contact plating shall be 50 microinches (1.27 m) gold in accordance with ASTM B488, type 3, code C, class 1.27, or 100 microinches (2.54 m) minimu

21、m tin-lead in accordance with SAE AMS-P-81728 over 50 microinches (1.27 m) minimum nickel in accordance with SAE AMS-QQ-N-290, class 2. Plated solder posts may be hot tin-lead dipped. Solderless wrappost: The solderless wrappost termination shall be in accordance with figures 2 and 3. Insulator: The

22、 insulator shall be one of the following types of plastic. All plastic material shall be rated V-0 in accordance with UL-94. a. Glass-or mineral-filled nylon in accordance with ASTM D4066. b. Glass filled thermoplastic in accordance with MIL-M-24519. c. Thermoplastic polyphenylene sulfide type GST-4

23、0F in accordance with ASTM D4067. Interface: See drawings 86038 and 86103. Printed wiring board (PWB) hole size: .040 inch (1.02 mm) .003 (0.08 mm). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-50

24、00 SIZE CAGE CODE DWG NO. A 037Z3 86099 REV D PAGE 6 Number of wrapped connections E length Wire gage 30 (mm) Wire gage 28 (mm) Wire gage 26 (mm) Wire gage 24 (mm) Wire gage 22 (mm) Wire gage 20 (mm) Wire gage 18 (mm) 1 .185 (4.70) .219 (5.56) .226 (5.74) .258 (6.55) .303 (7.70) .327 (8.31) .391 (9.

25、93) 2 .320 (8.13) .388 (9.86) .402 (10.21) .466 (11.84) .556 (14.12) .604 (15.34) .732 (18.59) 3 .455 (11.56) .557 (14.15) .578 (14.68) .674 (17.12) .809 (20.55) .881 (22.38) 1.073 (27.25) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 2. Wra

26、ppable length (typical connection). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE CAGE CODE DWG NO. A 037Z3 86099 REV D PAGE 7 Inches mm .0012 .0015 .003 0.030 0.038 0.076 A (mm) B (mm) C

27、 (mm) Parallelism (mm) Straightness Inch/inch (mm) .025 (0.64) nominal .022 (0.56) min .025 (0.64) nominal .022 (0.56) min .0355 (0.902) max .0325 (0.826) min .002 (0.05) .005 (0.13) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. FIGURE 3. Wrappost

28、geometry. Marking: The Part or Identifying Number (PIN) shall be marked on the housing and package in accordance with MIL-STD-1285. If size, surface condition, or other design considerations dont allow for full marking on the part, marking on the package is only required. The PIN shall include the c

29、omplete DSCC PIN, manufacturers name or CAGE code, and date code. The marking shall be permanent and legible in accordance with method 215 of MIL-STD-202. The PIN shall be constructed using the following format: 86099 XX -X YY Drawing Pin length Plating Number of positions number (see table I) (see

30、table II) (see table III) .BURR .0015 MAX.003 R MAXBCC.0012 MAXIMUM PERMISSIBLEDIVIATION FROM SQUARE ORRECTANGLEAProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE CAGE CODE DWG NO. A 037Z3 86

31、099 REV D PAGE 8 Approved source of supply: An approved source of supply is listed herein. Additional sources will be added as they become available. The vendor listed on the requirements drawing has agreed to this drawing and a certificate of compliance has been submitted to DLA land and Maritime-V

32、AI. DSCC drawing PIN Vendor CAGE number OAKZ5 1/ 8N187 1/ 95238 1/ 86099-01-X-YY 86099-02-X-YY 86099-03-X-YY 86099-04-X-YY 86099-05-X-YY 86099-06-X-YY 86099-07-X-YY 86099-08-X-YY 86099-09-X-YY 86099-10-X-YY 86099-11-X-YY 86099-12-X-YY 86099-13-X-YY 86099-14-X-YY 86099-15-X-YY 86099-16-X-YY 86099-17-

33、X-YY 86099-18-X-YY 86099-19-X-YY 86099-20-X-YY 86099-21-X-YY 86099-22-X-YY 86099-23-X-YY 86099-24-X-YY 86099-25-X-YY 86099-26-X-YY 86099-27-X-YY 86099-28-X-YY 86099-29-X-YY 86099-30-X-YY SPEG099-01-XYYMIL SPEG099-02-XYYMIL SPEG099-03-XYYMIL SPEG099-04-XYYMIL SPEG099-05-XYYMIL SPEG099-06-XYYMIL SPEG0

34、99-07-XYYMIL SPEG099-08-XYYMIL SPEG099-09-XYYMIL SPEG099-10-XYYMIL SPEG099-11-XYYMIL SPEG099-12-XYYMIL SPEG099-13-XYYMIL SPEG099-14-XYYMIL SPEG099-15-XYYMIL SPEG099-16-XYYMIL SPEG099-17-XYYMIL SPEG099-18-XYYMIL SPEG099-19-XYYMIL SPEG099-20-XYYMIL SPEG099-21-XYYMIL SPEG099-22-XYYMIL SPEG099-23-XYYMIL

35、 SPEG099-24-XYYMIL SPEG099-25-XYYMIL SPEG099-26-XYYMIL SPEG099-27-XYYMIL SPEG099-28-XYYMIL SPEG099-29-XYYMIL SPEG099-30-XYYMIL 69157XYY-MIL 68783XYY-MIL 67996XYY-MIL 68692XYY-MIL 68737XYY-MIL 68602XYY-MIL 67997XYY-MIL 68739XYY-MIL 68438XYY-MIL 69133XYY-MIL 68799XYY-MIL 68491XYY-MIL 68481XYY-MIL 6873

36、4XYY-MIL 67998XYY-MIL 68690XYY-MIL 68691XYY-MIL 67999XYY-MIL 68743XYY-MIL 68779XYY-MIL 68716XYY-MIL 68749XYY-MIL 68693XYY-MIL 68738XYY-MIL 68601XYY-MIL 68464XYY-MIL 68439XYY-MIL 68482XYY-MIL 69132XYY-MIL 68600XYY-MIL H211-YY-01-X H211-YY-02-X H211-YY-03-X H211-YY-04-X H211-YY-05-X H211-YY-06-X H211-

37、YY-07-X H211-YY-08-X H211-YY-09-X H211-YY-10-X H211-YY-11-X H211-YY-12-X H211-YY-13-X H211-YY-14-X H211-YY-15-X H211-YY-16-X H211-YY-17-X H211-YY-18-X H211-YY-19-X H211-YY-20-X H211-YY-21-X H211-YY-22-X H211-YY-23-X H211-YY-24-X H211-YY-25-X H211-YY-26-X H211-YY-27-X H211-YY-28-X H211-YY-29-X H211-Y

38、Y-30-X 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are meet. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43216-5000 SIZE CAGE CODE DWG NO. A 037Z3

39、86099 REV D PAGE 9 Vendor CAGE Vendor name number and address OAKZ5 Muller-Crane 1208 Massillon Road Building G Suite 1500n Akron, OH 44306 8N187 T.T.I 4033 E. Bellknap Street Fort Worth, TX 76111-6600 95238 Continental Connector Company 53 La France Avenue Bloomfield, NJ 07003-5632 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-