DLA DSCC-DWG-85116 REV D-2014 CONTACT ASSEMBLY ELECTRICAL.pdf

《DLA DSCC-DWG-85116 REV D-2014 CONTACT ASSEMBLY ELECTRICAL.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-85116 REV D-2014 CONTACT ASSEMBLY ELECTRICAL.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Corrections made to the contact and support arm dimensions and deletion of the suggested source of supplies. Editorial changes throughout. 6 Aug 85 Randy Larson B Updated boilerplate and references. 19 Apr 02 Kendall Cottongim C Updated boilerplate. Inactiv

2、ate drawing due to lack of supplier. 14 Feb 07 Michael A. Radecki D Updated boilerplate. 3 Jan 14 Michael A. Radecki Prepared in accordance with ASME Y14.100 REV STATUS OF PAGES REV D D D D D D D D D D PAGES 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Chris Rauch DESIGN ACTIVITY DEFENSE ELECTRONICS SU

3、PPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 7 October 1985 CHECKED BY Randy Larson TITLE CONTACT ASSEMBLY, ELECTRICAL APPROVED BY Ivan R. Jones SIZE A CODE IDENT. NO. 037Z3 DWG NO. 85116 REV D PAGE 1 OF 10 AMSC N/A 5999-2014-E04 Notice of Inactivation for New Design DLA Land and Marit

4、ime Drawing 85116 is inactive for new design and is no longer used, except for replacement purposes. CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

5、IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85116 REV D SHEET 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for an electrical contact assembly. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 85116 -01 Drawing

6、 number Dash number 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While

7、 every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and hand

8、books. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. FEDERAL SPECIFICATION QQ-B-654 - Brazing Alloys, Silver. DEPARTMENT OF

9、 DEFENSE STANDARDS MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/quicksearch.dla.mil/ or https:/assist.dla.mil/or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non

10、-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. AMERICAN SOCIETY FOR TESTING AND MATERIALS INTERNATIONAL (ASTM) ASTM B272 - Copper

11、 Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip.) ASTM B631 - Silver-Tungsten Electrical Contact Materials. ASTM B700 - Electrodeposited Coatings of Silver for Engineering Use. (Copies of this document are available on http:/ www.astm.org/ or from American Society for Testi

12、ng and Materials International (ASTM), 100 Barr Harbor Drive, P. O. Box C700, West Conshohocken, PA, 19428-2959.) SOCIETY OF AUTOMOTIVE ENGINEERS, INTERNATIONAL (SAE) SAE AMS-QQ-S-763 - Steel Bars, Wire, Shapes and Forgings, Corrosion Resistant. (Copies of this document are available on http:/www.sa

13、e.org/ or from Society of Automotive Engineers International (SAE), 400 Commonwealth Drive, Warrendale, PA, 15096-0001.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO

14、. 85116 REV D SHEET 3 2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been

15、obtained. 3. REQUIREMENTS 3.1 Material. 3.1.1 Contact. Contact material shall be silver-tungsten, class A in accordance with ASTM B631 (see figure 2). 3.1.2 Body. Body of contact plate shall be copper in accordance with C10100 of ASTM B272 (see figure 3). 3.1.3 Support arm. The body of the support a

16、rm shall be stainless steel, class 302 or 304, in accordance with SAE AMS-QQ-S-763 (see figure 4). 3.2 Plating. The body of the contact shall be silver plated in accordance with ASTM B700. 3.3 Welding. The silver contact shall be silver (60 percent) braze (AWS: BAg 7 in accordance with QQ-B-654), or

17、 spot welded (no pitting of contact surface permitted) to plate. 3.4 Riveting. The contact arm shall be riveted using a .125 x .375 nominal size, solid 100 countersunk head, copper rivet to the support arm (see figure 1). 3.5 Interface and physical dimensions. See figures 1, 2, 3, and 4 respectively

18、. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantag

19、eous life cycle costs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85116 REV D SHEET 4 Ltr Inches Millimeters Min Max Min Max A .220 .230 5.59 5.84 B .370 .380 9.4

20、0 9.65 C .120 .130 3.05 3.30 NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals. 3. Metric equivalents are given for general information only. FIGURE 1. Contact-electrical assembly dimensions and configurations. Provided by IHSNo

21、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85116 REV D SHEET 5 NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place dec

22、imals. 3. Metric equivalents are given for general information only. FIGURE 2. Contact-dimensions and configurations. Ltr Inches Millimeters Min Max Min Max D .870 .880 22.10 22.35 E .370R .380R 9.40R 9.65R F 1.245 1.255 31.62 31.88 G .745 .755 18.92 19.18 H .0575R 0675R 1.461R 1.714R J .745 .755 18

23、.92 19.18 K .183 .193 4.65 4.90 L .058 .068 1.47 1.73 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85116 REV D SHEET 6 FIGURE 3. Contact-arm dimensions and configur

24、ations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85116 REV D SHEET 7 NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerances are .005 (0.1

25、3 mm) for three place decimals and .02 (0.5 mm) for two place decimals. 3. Metric equivalents are given for general information only. 4. Unless otherwise specified, countersink all holes 90 x .031 (0.79 mm), both sides. FIGURE 3. Contact-arm dimensions and configurations - Continued. Ltr Inches Mill

26、imeters Min Max Min Max A .745 .755 18.92 19.18 B .025 .045 0.64 1.14 C .20 .24 5.1 6.1 D 1.36 1.40 34.5 35.6 E .48 .52 12.2 13.2 F .438 .448 11.13 11.38 G 3.620 3.630 91.95 92.20 H 3.245 3.255 82.42 82.68 J 1.120 1.130 28.45 28.70 K .370 R .380 R 9.40 R 9.65 R L .495 R .505 R 12.57 R 12.83 R M .48

27、.52 12.2 13.2 N .125 .128 3.18 3.25 P .0575 .0675 1.461 1.715 Q .266 .269 6.76 6.83 R .057 .067 1.45 1.70 S .870 .880 22.10 22.35 T .433 .443 11.00 11.25 U .183 .193 4.65 4.90 V .995 1.005 25.27 25.53 W 2.058 2.068 52.27 52.53 X 2.270 - 57.66 - Y .188 .191 4.78 4.85 Z .183 .193 4.65 4.90 AA 1.245 1.

28、255 31.62 31.88 BB .04 .08 1.0 2.0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85116 REV D SHEET 8 NOTES: 1. Dimensions are in inches. 2. Unless otherwise specifie

29、d, tolerances are .005 (0.13 mm) for three place decimals. 3. Metric equivalents are given for general information only. 4. Unless otherwise specified, countersink all holes 90 x .031 (0.79 mm), both sides. FIGURE 4. Support arm dimensions and configurations. Ltr Inches Millimeters Min Max Min Max A

30、 3.620 3.630 91.95 92.20 B 3.245 3.255 82.42 82.68 C 2.058 2.068 52.27 52.53 D .995 1.005 25.27 25.53 E .433 .443 11.00 11.25 F .125 .128 3.18 3.25 G .0575 .0675 1.461 1.715 H .266 .269 6.76 6.83 J .057 .067 1.45 1.70 K .183 .193 4.65 4.90 L .120 .130 3.05 3.30 M .870 .880 22.10 22.35 N .183 .193 4.

31、65 4.90 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85116 REV D SHEET 9 3.7 Manufacturer eligibility. To be eligible for listing as a suggested source of supply, a

32、 manufacturer shall perform the Group A and inspections specified herein on a sample of parts agreed upon by the manufacturer and DLA Land and Maritime-VA. 3.8 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3

33、.9 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of contact assembly and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.4). 3.10 Marking. Marking shall be i

34、n accordance with MIL-STD-1285, except the contact assembly shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.11 Workmanship. Parts shall be free of flash pits, voids, burrs, and excessive weld ma

35、terial, visible parting line is acceptable. Round all corners. 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified, inspection procedures shall be performed in accordance with Table I . The sampling plan shall be as specified in Table II. 4.2 Conformance inspection. 4.2.1 Inspect

36、ion of product for delivery. Inspection of product for delivery shall consist of group A inspection. 4.2.1.1 Group A inspection. Group A inspection shall consist of the inspections specified in Table I in the order shown. Rejected lots shall not be shipped. 4.2.2 Criteria for defects. All dimensiona

37、l characteristics are considered defective when out of tolerance. All physical and functional properties are considered defective when outside the specified minimum or maximum range as applicable. The specified sampling plan for each category is applicable to the cumulative defects for that category

38、 found in the sample. TABLE I. Group A inspection. Inspection Requirement paragraph Visual and mechanical Material Dimensions Workmanship 3.1 3.5 3.11 Table II. Lot and sample size Lot size Sample size 1 to 544 545-3,072 3,073 and over 80 units 128 units 192 units Provided by IHSNot for ResaleNo rep

39、roduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85116 REV D SHEET 10 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see

40、6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activities within the M

41、ilitary Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section

42、contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Devices conforming to this drawing are intended for use when military specifications do not exist and qualified military devices that will perform the required function are not avai

43、lable for the OEM application. 6.2 Replaceability. Devices covered by this drawing will replace the commercial device covered by contractor prepared specification or drawing. 6.3 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements fo

44、r delivery of one copy of the conformance inspection data or the certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Whether the manufacturer performs the group A inspection tests or provides certificate of compliance with group

45、 A requirements. d. Requirement for notification of change of product to the acquiring activity, if applicable. e. Requirements for packaging and packing. 6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufa

46、cture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead

47、, by mass, have shown to inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). 6.5 Users of record. Coordination of this document for future revisions is coordinated only with the suggested sou

48、rce(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at mailto: relaydla.mil or if in writing to: DLA Land and Maritime, Columbus, ATTN: DLA Land and Maritime/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-4481 or DSN 850-4481. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-