DLA DSCC-DWG-10023-2013 CONNECTOR PLUG EXPANDED BEAM HYBRID (2 SINGLE MODE& 2 MULTIMODE CHANNELS).pdf

《DLA DSCC-DWG-10023-2013 CONNECTOR PLUG EXPANDED BEAM HYBRID (2 SINGLE MODE& 2 MULTIMODE CHANNELS).pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-10023-2013 CONNECTOR PLUG EXPANDED BEAM HYBRID (2 SINGLE MODE& 2 MULTIMODE CHANNELS).pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A 6060-E032 REVISIONS LTR DESCRIPTION DATE APPROVED Prepared in accordance with ASME Y14.100 PMIC N/A PREPARED BY Mary McWilliams DESIGN ACTIVITY DLA LAND and MARITIME COLUMBUS, OH Original date of drawing 16 August 2013 CHECKED BY Mary McWilliams TITLE CONNECTOR PLUG, EXPANDED BEAM, HYBRID

2、(2 SINGLE MODE General Specification Governing the Manufacture, Assembly, and Inspection of MIL-PRF-85045/8 Cable, Fiber Optic, Radiation Hardened, Cable Configuration Type 1 (Buffered Fiber), Application E (Ground Tactical), Cable Class MM, (Metric) MIL-PRF-83526/20 Connector, Fiber Optic Plug, Cir

3、cular Hermaphroditic, In-Line Mount, 2 and 4 Positions, Expanded Beam. DEPARTMENT OF DEFENSE STANDARD MIL-STD-1285 - Marking of Electrical and Electronic Parts (Copies of these documents are available online at http:/quicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Av

4、enue, Building 4D, Philadelphia, PA 19111-5094.) Provided by IHSNot for Resale-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10023 REV PAGE 3 2.4 Order of precedence. Unless otherwise noted herein, in the event of a conflict between the text of this document and the re

5、ferences cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS FIGURE 1. Single mode expanded beam connector plug FIGURE 2. Multi-mode expanded beam connec

6、tor plug channel marking requirements. channel marking requirements. FIGURE 3. Mixed mode expanded beam connector plug channel marking requirements. Provided by IHSNot for Resale-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10023 REV PAGE 4 3.1 General. The requiremen

7、ts for acquiring the product described herein shall consist of MIL-DTL-83526/20 as modified by this drawing. 3.2 Interface and physical dimensions. Detailed dimensions shall be as specified in MIL-DTL-83526/20 for the four channel configuration. 3.3 Materials. Materials shall be as specified in MIL-

8、DTL-83526/20 with the following exception. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.

9、4 Identification marking. 3.4.1 Item marking (PIN). Item marking shall be applied to the coupling nut in accordance with MIL-STD-1285, except the (part name) shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date l

10、ot codes. 3.4.2 Channel marking requirements. Channels shall be identified on both ends of the inserts. See figure 1 for marking on lens end of the insert. 3.4.3 Additional markings. Additional markings shall be as specified in MIL-DTL-83526/20, the colors of the protective cap, rubber grip and boot

11、 of the connector plug shall be in accordance with FED-STD-595: -01: Green 383 camouflage chip number 34094 -02: Black camouflage chip number 37030 -03: Brown 383 camouflage chip number 30051 3.5 Protective cap. Connector plug shall be supplied with a protective cap as specified in MIL-DTL-83526/20.

12、 3.6 Optical requirements. 3.6.1 Insertion loss. Insertion loss is applicable as specified in MIL-DTL-83526/20. 3.6.2 Crosstalk. Cross talk is applicable, as specified in MIL-DTL-83526/20. 3.6.3 Return loss. Return loss is applicable as specified in MIL-DTL-83526/20. 3.6.4 Lens anti-reflection (AR)

13、coating performance. 3.6.4.1 Abrasion resistance: Shall meet the severe abrasion requirements as specified in 3.8.4.1 of MIL-C-675. 3.6.3.2 Lens scratch and dig resistance. Lenses shall have a surface quality of 40/20 and shall pass the scratch and dig requirements in MIL-PRF-13830. 3.7 Optical fibe

14、r/cable requirements. Optical fiber/cable requirements shall be in accordance with MIL-PRF-85045/30 for two channel single mode or MIL-PRF-85045/8 for two channel multimode fibers or DLA LAND and MARITIME drawing 09001 for a mixed mode cable. 3.8 Manufacturer eligibility. 3.8.1 Qualified. To be elig

15、ible for listing as an approved source of supply on this drawing (see approved sources of supply 6.3 and table IV), a manufacturer shall be listed on the MIL-DTL-83526/20 Qualified Products Database. 3.8.2 Approval testing. To be eligible for listing as an approved source of supply on this drawing (

16、see approved sources of supply 6.3 and table IV), a manufacturer shall perform tests specified in table II. 3.8.3 Interoperability and intermateability. To be eligible for listing as an approved source of supply on this drawing (see approved sources of supply 6.3 and table IV), a manufacturer shall

17、pass interoperability and intermateability testing. 3.9 Workmanship. The connector receptacle shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHSDLA L

18、AND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10023 REV PAGE 5 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified, sampling and inspection procedures shall be performed in accordance with this drawing and MIL-DTL-83526/20. 4.2 Approved source of supply (Man

19、ufacturer eligibility). To be an approved source of supply a manufacturer must complete the following; 4.2.1 Qualified. Manufacturer shall be listed on the MIL-DTL-83526/20 Qualified Products Database. Qualification by similarity requirements of MIL-DTL-83526/20 shall apply. 4.2.2 Approval testing.

20、Manufacturer shall submit results of tests specified in table II to: DLA Land and Maritime-VAT, P. O. Box 3990, Columbus, Ohio 43218-3990. TABLE II. Approval testing. 1/ Requirement Test 3.2 Interface and physical dimensions 3.3 Materials 3.4 Identification marking 3.5 Protective cap 3.6.1 Insertion

21、 loss 3.6.2 Cross talk 3.6.3 Return loss 3.9 Workmanship 1/ For approval, sample must pass these tests. 4.2.2 Interperability testing. a. Background. DLA Land and Maritime will partner with companies in an effort to verify interoperability of fiber optic connector plugs with other fiber optic connec

22、tor plugs, (DLA Land and Maritime drawing 10023). This partnership allows the Government to verify the interoperability of manufacturers connector with that of other participating manufacturers. Your continued participation with this partnering effort is appreciated. b. Company agreements. Your comp

23、any is being requested to provide 2 (two) connector assemblies terminated to cable as specified in paragraph 3.7, each channel configured with the appropriate fiber optic leads terminated to ST connectors (see MIL-DTL-83526/20 figure 8) referred to herein as interoperability standards so that the Go

24、vernment can perform interoperability testing. By providing these interoperability standards, your company agrees that these interoperability standards are to be retained by the Government. Also, your company agrees to replace or refurbish these interoperability standards at no cost to the Governmen

25、t as the need arises. c. Government agreements & control of interoperability standards. The Government agrees to retain the interoperability standards. Under this agreement, these interoperability standards are to be used only by Government, in-house personnel. Only personnel to be present during in

26、teroperability testing are Government, in-house personnel. At no time would other parties have access to or examination of the interoperability standards. d. Points of contact. Please inform us if you have any concerns or objections relating to this submittal of test samples. Direct your questions o

27、r comments to DLA Land and Maritime-VAT point of contact for fiber optic component testing by telephone: (614) 692-0571or E-mail: FiberOpticGroupdla.mil . Otherwise, direct your questions concerning submittal of test samples and vendor costs for interoperability testing to our test laboratory point

28、of contact, Greg Vaughn. He can be contacted by telephone: (614) 692-9891 or E-mail: ElectronicsPTC.SiteManager.DSCCdla.mil. Provided by IHSNot for Resale-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10023 REV PAGE 6 4.3 Conformance inspection. Conformance inspection

29、(inspection prior to delivery) shall consist of inspections specified in table III. TABLE III Conformance inspection. Requirement Inspection 3.2 Interface and physical dimensions 3.4 Identification marking 3.5 Protective cap 3.6.1 Insertion loss 5. PACKAGING 5.1 Packaging. For acquisition purposes,

30、the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements a

31、re maintained by the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM product

32、s, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1

33、.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. 6.3 Users of record. Coordination of this document f

34、or future revisions is coordinated only with the approved source(s) of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at FiberOpticGroupdla.mil or if in writing to: Defense Supply Center, Columbus, ATTN: DLA Land and Ma

35、ritime/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0571 or DSN 850-0571. Provided by IHSNot for Resale-,-,-DLA LAND AND MARITIME COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 10023 REV PAGE 7 6.4 Approved source(s) of supply. Current approved source(s) of supply

36、 are listed in table III. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at FiberOpticGroupdla.mil , or by contacting Defense Supply Center, Columbus, ATTN: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-39

37、90 or by telephone (614) 692-0571 or DSN 850-0571. TABLE IV Approved source(s) of supply. DLA Land and Maritime drawing PIN Vendor similar designation or type number 1/, 2/ Vendor CAGE Vendor name and address 10023-01 10023-02 10023-03 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. 2/ At the time this drawing was developed, no approved sources were available. Provided by IHSNot for Resale-,-,-