DLA DSCC-DWG-08008 REV B-2009 STRAINER ELEMENT.pdf

《DLA DSCC-DWG-08008 REV B-2009 STRAINER ELEMENT.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-08008 REV B-2009 STRAINER ELEMENT.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、REVISIONS LTR DESCRIPTION DATE APPROVED A Figures 3 and 4 changed tolerances on 1.30 dimension from .010 to .10. Changed e-mail address for comments. 6 June 2008 Abdo Abdouni B Page 5 added see note 8 to figure 5. Page 6 clarified perforations to detail A, note 5 removed MIL-STD-278 and replaced wit

2、h MIL-STD-22, added note 8, table I correct welding method and welding wire call-out. Editorial changes throughout. 29 May 2009 Abdo Abdouni Prepared in accordance with ASME Y14.100 Detail Drawing REV PAGE REV B B B B B B B B REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 PREPARED BY PMIC N/A William Carp

3、enter DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 CHECKED BY TITLE Ernest Brown APPROVED BY Abdonasser M. Abdouni STRAINER ELEMENT SIZE CAGE CODE 16236 DWG. NO.08008 Original date of drawing 19 March 2008 A REV B PAGE 1 OF 8 AMSC N/A 4730-F004-001 Provided by IHSNot for ResaleNo reprod

4、uction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 16236 08008 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE2 FIGURE 1. Strainer element. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwis

5、e specified tolerance is .015 inch (0.38 mm). 4. Break all sharp edges. FIGURE 2. Handle. .380 2 PLACES1.200 1.500 .250Inches mm .250 .380 1.20 1.500 6.35 9.65 30.5 38.10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 16236 08

6、008 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE3 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerance is .015 inch (0.38 mm). 4. Break all sharp edges. FIGURE 3. Flange, top. Inches mm .10 .030 .120

7、.440 1.30 2.00 2.5 0.76 3.05 11.18 33.0 50.8 .120 R .030 REF .440 1.30 .10 2.00 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 16236 08008 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE4 NOTES: 1. Dimensio

8、ns are in inches. 2. Metric equivalents are given for information only. 3 Unless otherwise specified tolerance is .015 inch (0.38 mm). 4. Break all sharp edges. FIGURE 4. Flange, bottom. 1.30 .10 .120 .380 Inches mm .10 .120 .380 1.30 2.5 3.05 9.65 33.0 Provided by IHSNot for ResaleNo reproduction o

9、r networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 16236 08008 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE5 FLANGE TOP PERFORATED CYLINDER (SEE DETAIL A AND NOTE 8) (EXCEPT AT OVERLAP).19 (4)RSW .19 (3)3.63 .12TYP. GTAW (2 PLACES)(SEE NOTES 5 AND 6)1.1

10、2 (SEE NOTES 4 AND 5)HANDLE 90 (4) .19 1.36.500 OVERLAP FLANGE BOTTOM RSW (SEE NOTE 4) RSW (SEE NOTE 4) .81 90 TOP VIEW FIGURE 5. Strainer element. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 16236 08008 DEFENSE SUPPLY CENT

11、ER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE6 DETAIL A - A NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified tolerance is .015 inch (0.38 mm). 4. Resistance spot weld (RSW) in accordance with American Welding Society AWS D17.2

12、. 5. Gas tungsten arc welding (GTAW) in accordance with MIL-STD-22. 6. Perforated cylinder form over mandrel and center spot welds on seam. 7. Remove all weld spatters and break all sharp edges. 8. Perforations in accordance with Industrial Perforations Association (IPA) pattern 113. FIGURE 5. Strai

13、ner element - Continued. REQUIREMENTS: Dimensions and configurations: See figures 1, 2, 3, 4, and 5. Dissimilar metals. Dissimilar metals (as specified in MIL-STD-889) shall not be used in the fabrication of this strainer. Material: Nickel copper alloy in accordance with QQ-N-281, class A, form 4, a

14、s rolled sheet, .030 inch (0.76 mm) thick. Welding wire shall be as specified in table I. TABLE I. Welding wire. Welding process Form Type Specification TIG or GTAW Wiring in straight lengths or spools MIL-RN60 MIL-E-21562 Inches mm .12 .19 .500 .81 1.12 1.36 3.63 3.1 4.8 12.70 20.6 28.5 34.5 92.2 P

15、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 16236 08008 DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 A REVB PAGE7 Preparation for welding: All traces of the elements which cause cracking (sulphur, phosphorus, lead

16、 etc) shall be removed. This includes crayons, paints, temperature indication markers, cutting fluids, oil and grease. Fittings of other alloys, such as gunmetal - copper-tin-zinc alloy - are also a source of detrimental elements and shall not be welded to copper-nickel alloys. The joint area shall

17、be thoroughly cleaned before welding starts. The weld preparation, and an adjacent area on either side of the preparation shall be degreased and any markings removed. Uncontaminated organic solvents should be applied with clean cloths and the area dried. The appearance of the cloths used for drying

18、is a useful indicator of cleanliness: they should be free of any residue. Stainless steel brushes shall be used and tools such as grinding discs shall not be used on Cu-Ni alloys if they have been used on other materials. Workmanship. Strainer elements shall be free from cracks, laps, burrs, or any

19、other defects that may detrimentally affect their intended use. Recycled, recovered, or environmentally preferable materials: Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and ma

20、intenance requirements, and promotes economically advantageous life cycle costs. Part or Identifying Number (PIN): The complete PIN shall be constructed using the following format: 08008 -1 DSCC Dash Requirement number drawing Packaging. For acquisition purposes, the packaging requirements shall be

21、as specified in the contract or order (see acquisition requirements). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained b

22、y the Inventory Control Points packaging activities within the Military Service or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contac

23、ting the responsible packaging activity. DSCC drawing use. Strainer elements in accordance with this drawing are intended for use when military specifications do not exist and qualified military strainer elements that will perform the required function are not available for OEM application. This dra

24、wing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawings, and stock catalog listings. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE CAGE CODE DWG NO. 16236 08008 DEFENSE SUPPLY CENTER, COLUMBU

25、S COLUMBUS, OH 43218-3990 A REVB PAGE8 Acquisition requirements. Acquisition documents should specify the following: a. Complete PIN. b. Requirements for delivery of one copy of the quality conformance inspection data pertinent to the strainer element inspection lot to be supplied with each shipment

26、 by the manufacturer, if applicable. c. Requirements for notification of change of product or process to contracting activity, if applicable. d. Packaging requirements. Comments. Comments on this drawing should be directed to Defense Supply Center, Columbus, ATTN: DSCC-VAI, P.O. Box 3990 Columbus, O

27、hio 43218-3990 or telephone (614) 692-0565, facsimile (614) 692-6940 or emailed to FluidFlowdla.mil. Supersession data. DSCC drawing 08008-1 replaces Defense Construction Supply Center (16236) drawing CS4730-SV-0735. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-