DLA DSCC-DWG-02008 REV B-2010 RESISTOR CHIP FIXED FILM LOW AND HIGH VALUES STYLE 1206 [Use ARMY MIL-PRF-55342 7 E (2) ARMY MIL-PRF-55342 7E (1) ARMY MIL-PRF-55342 7E ARMY MIL-PRF-5.pdf

《DLA DSCC-DWG-02008 REV B-2010 RESISTOR CHIP FIXED FILM LOW AND HIGH VALUES STYLE 1206 [Use ARMY MIL-PRF-55342 7 E (2) ARMY MIL-PRF-55342 7E (1) ARMY MIL-PRF-55342 7E ARMY MIL-PRF-5.pdf》由会员分享，可在线阅读，更多相关《DLA DSCC-DWG-02008 REV B-2010 RESISTOR CHIP FIXED FILM LOW AND HIGH VALUES STYLE 1206 [Use ARMY MIL-PRF-55342 7 E (2) ARMY MIL-PRF-55342 7E (1) ARMY MIL-PRF-55342 7E ARMY MIL-PRF-5.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add new vendor, and correct table I. Editorial changes throughout. 9 JUL 04 K. Cottongim B Partial inactivation for new design. Editorial changes throughout. 4 MAY 10 M. Radecki Notice of Partial Inactivation for New Design DSCC Drawing 02008 is inactive fo

2、r new design for characteristics H, K, and M and is no longer used, except for replacement purposes. Use MIL-PRF-55342/7 for new designs. Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS REV B B B B B B OF PAGES PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Dennis L. Cross DEFENSE

3、 SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 31 October 2002 CHECKED BY Andrew R. Ernst TITLE RESISTOR, CHIP, FIXED, FILM, LOW AND HIGH VALUES, STYLE 1206 APPROVED BY Kendall A. Cottongim SIZE A CODE IDENT. NO. 037Z3 DWG NO. 02008 REV B PAGE 1 OF 6 AMSC N/A 5905-E700 Provided by IH

4、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02008 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a chip resistor, style 1206 with low and high resi

5、stance values, a wide range of characteristics and tolerances. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 02008- L 1R00 F B | | | | | | | | | | Drawing number Characteristic (see 3.3.1) Resistance (see 3.3.2) Tolerance (see 3.3.3) Termination (see 3.

6、3.4) 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications and standards. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contra

7、ct. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-55342 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Reliability, Space Level, General Specification for. MIL-PRF-55342/7 - Resistors, Chip, Fixed, Film, Nonestablished Reliability, Established Reliability, Space Level, Style

8、1206. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-690 - Failure Rate Sampling Plans and Procedures. MIL-STD-790 - Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications. * (Copies of these documents are availabl

9、e online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) * 2.2 Order of precedence. Unless otherwise noted herein or in the event of a conflict between the text of this document and the referen

10、ces cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3.1 Item requirements. The individual item requirements shall be in acc

11、ordance with MIL-PRF-55342, and as specified herein. 3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified in MIL-PRF-55342/7 and herein (see figure 1). 3.3 Electrical characteristics. Provided by IHSNot for ResaleNo reproduction or network

12、ing permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02008 REV B PAGE 3 3.3.1 Characteristic. Resistors are available in characteristics L, and N (characteristics H, K, M are inactive for new design, use MIL-PRF-55342/7) in acc

13、ordance with the resistance tolerances and resistance values as specified in table I and paragraph 6.7 herein. 3.3.2 Resistance. The nominal resistance is expressed in ohms and is identified by four digits; the first three digits represent significant figures and the last digit specifies the number

14、of zeros to follow. When the values of resistance are less than 100 ohms, or when fractional values of an ohm are required, the letter “R“ is substituted for one of the significant digits to represent the decimal point. When the letter “R“ is used, succeeding digits of the group represent significan

15、t figures. 3.3.2.1 Resistance range. The resistance range shall be 1 ohm to 10 Megohms in accordance with the characteristics and resistance tolerances as specified in table I and paragraph 6.7 herein. 3.3.3 Resistance tolerance. Resistors are available in resistance tolerances F(1 percent), G(2 per

16、cent), J(5 percent), and K(10 percent) in accordance with the characteristics and resistance values as specified in table I and paragraph 6.7 herein. TABLE I. Resistance temperature characteristic, resistance, and resistance tolerance. Characteristic PPM Tolerance Resistance range 1 percent (F) 2 an

17、d 5 percent (G, J) 10 percent (K) H 1/ 50 1 ohm thru 5.49 ohms 5.76 Megohms thru 10 Megohms 1 ohm thru 5.1 ohms 6.2 Megohms thru 10 Megohms 1 ohm thru 4.7 ohms 6.8 Megohms thru 10 Megohms K 1/ 100 M 1/ 300 L 200 1 ohm thru 10 Megohms N 400 1/ Inactive for new design. 3.3.4 Termination material. Term

18、ination material shall be in accordance with MIL-PRF-55342, code letter B. * 3.3.4.1 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed

19、with a minimum of 3 percent lead, by mass (see 6.3). 3.3.5 Power rating. The power rating for all characteristics shall be 250 milliwatts at 70C derated to zero power at +150C. 3.3.6 Voltage rating. The maximum continuous working voltage shall not exceed 100 volts. 3.4 Marking. Marking is not requir

20、ed on the resistor; however, each unit package shall be marked with the PIN assigned herein (see 1.2), vendor CAGE code, and date and lot codes. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximu

21、m extent possible provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageous life cycle costs. * 3.6 Manufacturer eligibility. To be eligible for listing as a approved source of supply, a manufacturer shall be listed on the MIL-PRF

22、-55342 Qualified Products List for at least one part, or perform the group A and group B inspections specified herein on a sample agreed upon by the manufacturer and DSCC-VA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLU

23、MBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02008 REV B PAGE 4 * 3.6.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be listed as an approved source of supply. 3.7 Workmanship. Resistors shall be uniform in quality and free from

24、 any defects that will affect life, serviceability, or appearance. Configuration A Configuration B Configuration Dimension A mm Dimension B mm Dimension C mm Dimension D mm Dimension E Mm A 3.20 0.13 1.60 0.13 0.30/0.76 0.51 +0.13 -0.25 N/A B 3.20 0.20 1.60 0.13 0.38/0.84 0.51 +0.13 -0.25 0.51 +0.13

25、 -0.25 NOTES: 1. Dimensions are in millimeters. 2. Inch equivalents are given for general information only. 3. The pictorial view of the styles above is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope, and do not

26、alter the functional aspects of the device are acceptable. 4. Configuration A is not applicable to this document. FIGURE 1. Chip resistor. mm Inches 0.13 0.005 0.20 0.008 0.25 0.010 0.30 0.012 0.38 0.015 0.51 0.020 0.76 0.030 0.84 0.033 1.60 0.063 3.20 0.126 Provided by IHSNot for ResaleNo reproduct

27、ion or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 02008 REV B PAGE 5 4. VERIFICATIONS 4.1 Product assurance program. The product assurance program specified in MIL-PRF-55342 and maintained in accordance with MI

28、L-STD-790 is not applicable to this document. 4.2 Product level qualification. The product level qualification specified in MIL-PRF-55342 and MIL-STD-690 is not applicable to this document. 4.3 Conformance provisions. 4.3.1 Inspection of product for delivery. Inspection of product for delivery shall

29、 consist of group A inspection and group B inspection of MIL-PRF-55342. 4.3.2 Certification. The procuring activity may accept a certificate of compliance in lieu of group B inspection (see 6.2d). 4.5 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design

30、, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-55342. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is

31、to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency,

32、or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general o

33、r explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Chip resistors are intended for use in thick or thin film circuits where microcircuitry is intended. Chip resistors can also be used in surface mount applications. 6.2 Ordering data. The contract or purchase order wil

34、l specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery, one copy of the conformance inspection data that parts have passed conformance inspection, with each shipment of parts by the manufacturer. c. Packaging requirements. (e.g., Electrostatic discharge (ESD) sensitivity) (

35、see 5.1). d. Whether the manufacturer performs the group B inspection or provides a certificate of compliance (see 4.3.2). * 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur

36、anytime from a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhib

37、it the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO

38、 SIZE A CODE IDENT NO. 037Z3 DWG NO. 02008 REV B PAGE 6 6.4 Electrostatic charge. Under several combinations of conditions, these resistors can be electrically damaged, by electrostatic charges, and drift from specified value. Users should consider this phenomena when ordering or shipping resistors.

39、 Direct shipment to the Government is controlled by MIL-DTL-39032 which specifies a preventive packaging procedure. * 6.5 Pulse applications. Designers are CAUTIONED on using the above resistors in high power pulse applications. Since they have not been qualified nor tested for such applications, da

40、mage and premature failure are possible. These resistors only see a one time pulse (Short-time overload) as part of the group B inspection of MIL-PRF-55342. * 6.6 User of record. Coordination of this document for future revisions is coordinated only with the approved source of supply and the users o

41、f record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. * 6.7 Approved source of supply. Approved source of s

42、upply is listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. DSCC drawing PIN 02008

43、-* Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address Char. L and N, res. value 1 ohm thru 10 Megohms, res. tol. 1, 2, 5, and 10 pct. WA87 PS-*-NS62P WA87 PS-*-NS62 50316 Mini-Systems, Inc. 20 David Rd. North Attleboro, MA 02760-2102 Char. L and N, res. value 1 ohm thru

44、 10 Megohms, res. tol. 1, 2, 5, and 10 pct. H1206CPX* (DEC008) 56235 State of the Art, Inc. 2470 Fox Hill Rd. State College, PA 16803-1797 Char. L, res. values 1 ohm thru 1 Megohm, res. tol. 1, 2, and 5 pct. W1206RV-0*-* 57027 TT Electronics/IRC 4222 S. Staples St. Corpus Christi, TX 78411-2702 Char

45、. L and N, res. value 1 ohm thru 10 Megohms, res. tol. 1, 2, 5, and 10 pct. RCWP-1206-14 SH903 Vishay Dale Electronics, Inc. PO Box 609 Columbus, NE 68602-0609 Plant: Vishay Israel, LTD. Emek-Sara “B” Industrial Park Beer Sheva, Israel 84874 Char. L, res. values 10 ohm thru 10 Megohms, res. tol. 1,

46、2, 5, & 10 pct. Char. N, res. values 1 ohm thru 10 Megohms, res. tol. 1, 2, 5, & 10 pct. M1206LXXXXZ L1206NXXXXZ M1206NXXXXZ SH903 Vishay Thin Film 2160 Liberty Drive Niagara Falls, NY 14304 Plant: Vishay Israel, LTD. Emek-Sara “B” Industrial Park Beer Sheva, Israel 84874 1/ Parts must be purchased to the DSCC PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-