DLA DESC-DWG-85136 REV E-2010 HEAT SINKS ELECTRICAL-ELECTRONIC COMPONENT FIN STOCK ALUMINUM ALLOY.pdf

《DLA DESC-DWG-85136 REV E-2010 HEAT SINKS ELECTRICAL-ELECTRONIC COMPONENT FIN STOCK ALUMINUM ALLOY.pdf》由会员分享，可在线阅读，更多相关《DLA DESC-DWG-85136 REV E-2010 HEAT SINKS ELECTRICAL-ELECTRONIC COMPONENT FIN STOCK ALUMINUM ALLOY.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Configuration E deleted. Configuration C redrawn. Width dimensions on table I clarified. Dash numbers 57 through 61 deleted from vendor table in 6.3. Vendor CAGE 16630 added. Several editorial corrections made. 12 May 87 Ivan Jones B Added dash number 057.

2、Changed dimension line on configuration B. Changed C, D, and E dimension values for several dash numbers in table I. Updated vendor part number in p6.4. Editorial corrections throughout. 30 Sep 88 Randy Larson C Added paragraph 3.10. Changed dimension B for dash number -003 on table I. Editorial cor

3、rections throughout. 13 Aug 90 Randy Larson D Added vendor 0K2D6. Editorial changes throughout. 14 Jul 93 D. Moore E Incorporated boilerplate updates and updated approved sources of supply list. 23 Feb 10 Michael A. Radecki Prepared in accordance with ASME Y14.100 Source control drawing REV STATUS O

4、F PAGES REV E E E E E E E E E E E E E PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Frank A. Crivello DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OH 45444-5000 Original date of drawing 10 September 1986 CHECKED BY Randy Larson TITLE HEAT SINKS, ELECTRICAL-ELECTRONIC COMPONEN

5、T, FIN STOCK, ALUMINUM ALLOY APPROVED BY Ivan Jones SIZE A CODE IDENT. NO. 14933 DWG NO. 85136 REV E PAGE 1 OF 13 AMSC N/A 5999-E244 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction

6、or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85136 REV D SHEET 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of aluminum alloy fin stock heat sinks for use with electronic componen

7、ts. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 85136 -01 Drawing number Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include document

8、s cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents in sections 3 and 4 of this spe

9、cification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are thos

10、e cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-19491 - Semiconductor Device, Packaging of. MIL-H-87111 - Heat Sinks, Semiconductor Devices, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Electronic and Electrical Component Parts. (Copi

11、es of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent speci

12、fied herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI B46.1 - Surface Texture (Surface Roughness, Waviness, and Lay). ANSI/NCSL-Z540 - Calibration Laboratories and Measuring and Test E

13、quipment- General Requirements (Copies of these documents are available online at http:/www.ansi.org or should be addressed to the American National Standards Institute, 11 West 42nd Street, New York, NY 10036-8002.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM B209 - Aluminum and Aluminum

14、-Alloy Sheet and Plate (Copies of these documents are available online at http:/www.astm.org or should be addressed to ASTM International PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

15、HS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85136 REV E SHEET 3 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein (except for related sp

16、ecification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Material. The material shall be annealed 3003 aluminum alloy sheet in accordance with ASTM

17、 B209. 3.2 Design and configurations. See figure 1. 3.3 PINs and dimensions. See table I. 3.4 Length. Length shall be specified on the purchase order (see figure 1). 3.5 Width. Width shall be as specified on the purchase order. Dash numbers 40 through 56 are normally available in one width only, but

18、 may be available in other widths from certain vendors. All other dash numbers are available in various widths not to exceed the maximum value specified in table I. 3.6 Surface roughness. Material surface roughness shall not exceed 40 microinches rms. 3.7 Statement in lieu of testing. The acquiring

19、activity, at its discretion, may accept from the manufacturer a statement of compliance with the group A requirements in lieu of the manufacturer performing the group A tests (see 4.4.1 and 6.2c). 3.8 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmental

20、ly preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.9 Certificate of compliance. A certificate of compliance shall be required from

21、manufacturers requesting to be an approved source of supply. 3.10 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent

22、lead, by mass (see 6.3). 3.11 Marking. The heat sinks need not be marked. Package marking shall be in accordance with MIL-DTL-19491. 3.12 Workmanship. The fin section shall not be bent, dented, crushed or otherwise damaged. First and last convolutions may vary from normal fin pitch and appearance an

23、d will not always be uniform. Some fins will not be straight or always vertical. Cut edges shall not be ragged or contain burrs or hanging slivers; such projections shall not be greater than twice the material thickness in height and shall be random in occurrence. Provided by IHSNot for ResaleNo rep

24、roduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85136 REV E SHEET 4 CONFIGURATION B - FINSTOCK, STRAIGHT FIN WITH ROUNDED CREST FIGURE 1. Design and configurations. FLAT CREST WILL MAINTAIN SHAPE A LOW

25、FIN/INCH DENSITIES UP TO APPROXIMATELY 10 FINS/INCH. ABOVE THIS DENSITY, THE TIPS MAY TAKE ON A “ROUNDED” APPEARANCE. CONFIGURATION A FINSTOCK, STRAIGHT FIN WITH FLAT CREST Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY CE

26、NTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85136 REV E SHEET 5 CONFIGURATION C - FINSTOCK, LANCED OFFSET WITH FLAT CREST CONFIGURATION D - FINSTOCK, LANCED OFFSET WITH CURVED FIN (SAME AS CONFIGURATION C EXCEPT AS SHOWN). NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given

27、 for general information only. 3. Unless otherwise specified, tolerance is .010 (0.25 mm) for three place decimals and .02 (0.5 mm) for two place decimals. FIGURE 1. Design and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

28、-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85136 REV E SHEET 6 TABLE I. PINs and dimensions. PIN 85136- Config- uration (see fig. 1) Dimensions (in.) Fins/In. ref Weight lb/ft Width inches A .001 B .003 C D E F G max 001 A .006 .300 .143 - - - - 14 - 11.5 m

29、ax 002 A .006 .250 .167 - - - - 12 - 11.5 max 003 B .006 .625 .133 - - - - 15 - 35.5 max 004 C .006 .375 .111 | 056 .028 .125 - 18 - 15.0 max 005 A .006 .375 .143 - - - - 14 - 11.5 max 006 C .006 .375 .133 .067 .033 .250 - 15 - 12.0 max 007 C .006 .315 .143 .071 .036 .625 - 14 - 12.0 max 008 C .006

30、.250 .133 .067 .033 .125 - 15 - 17.5 max 009 C .006 .100 .167 .083 .041 .125 - 12 - 9.0 max 010 A .006 .100 .250 - - - - 8 - 12.0 max 011 B .006 .500 .143 - - - - 14 - 12.0 max 012 C .006 .500 .111 .056 .028 .125 - 18 - 17.5 max 013 C .006 .250 .167 .083 .041 - - 12 - 9.0 max 014 C .006 .375 .167 .0

31、83 .041 .125 - 12 - 10.0 max 015 B .006 .250 .111 - - - - 18 - 10.0 max 016 B .008 .375 .111 - - - - 18 - 10.0 max 017 A .004 .100 .143 - - - - 14 - 12.0 max 018 A .004 .250 .111 - - - - 18 - 12.0 max 019 D .004 .940 .250 .125 .062 .875 .100 8 - 12.0 max 020 D .004 .625 .200 .100 .050 .375 .080 10 -

32、 18.0 max 021 A .010 .625 .400 - - - - 5 - 12.0 max 022 C .006 .250 .154 .077 .039 .625 - 13 - 12.0 max 023 C .006 .500 .167 .084 .042 .250 - 12 - 12.0 max 024 C .006 .120 .133 .067 .033 .250 - 15 - 17.0 max Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

33、S-,-,-DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85136 REV E SHEET 7 TABLE I. PINs and dimensions - Continued. PIN 85136- Config- uration (see fig. 1) Dimensions (in.) Fins/In. ref Weight lb/ft Width inches A .001 B .003 C D E F G max 025 B .006 .500 .100 - -

34、- - 20 - 12.0 max 026 A .006 .500 .167 - - - - 12 - 12.0 max 027 A .006 .375 .111 - - - - 18 - 18.0 max 028 A .006 .312 .133 - - - - 15 - 7.0 max 029 C .006 .300 .143 .071 .036 .300 - 14 - 16.0 max 030 B .006 .250 .167 - - - - 12 - 18.0 max 031 B .006 .112 .133 - - - - 15 - 17.5 max 032 C .006 .300

35、.154 .077 .051 .250 - 13 - 16.5 max 033 A .006 .100 .200 - - - - 10 - 17.5 max 034 C .006 .125 .100 .050 .028 .125 - 20 - 12.0 max 035 A .006 .100 .167 - - - - 12 - 17.5 max 036 A .006 .230 .250 - - - - 8 - 17.5 max 037 A .006 .250 .100 - - - - 20 - 12.0 max 038 C .006 .100 .067 .034 .017 .125 - 30

36、- 17.5 max 039 A .010 .375 .167 - - - - 12 - 18.0 max 040 C .006 .100 .167 .083 .042 .250 - 12 .047 18.00 .01 041 C .005 .100 .167 .083 .042 .250 - 12 .038 18.00 .01 042 C .010 .375 .133 .067 .033 .125 - 15 .71 9.03 .03 043 C .006 .100 .167 .083 .042 .250 - 12 .033 12.25 .01 044 C .006 .315 .143 .07

37、1 .036 .625 - 14 .24 6.00 .06 045 C .006 .250 .154 .077 .039 .625 - 13 .12 2.80 .02 046 C .006 .375 .100 .050 .025 .125 - 20 .56 4.00 .01 047 C .006 .250 .100 .050 .025 .125 - 20 .13 1.62 .02 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE EL

38、ECTRONICS SUPPLY CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85136 REV E SHEET 8 TABLE I. PINs and dimensions - Continued. PIN 85136- Config- uration (see fig. 1) Dimensions (in.) Fins/In. ref Weight lb/ft Width inches A .001 B .003 C D E F G max 048 C .006 .250 .100 .050 .025 .125 - 20

39、.091 3.00 .02 049 C .006 .375 .100 .050 .025 .125 - 20 .12 3.00 .02 050 C .006 .500 .167 .083 .042 .250 - 12 .28 5.5 .01 051 C .006 .250 .100 .050 .025 .625 - 20 .52 12.0 .01 052 C .006 .250 .133 .067 .033 .125 - 15 .09 2.68 .02 053 C .006 .250 .133 .067 .033 .125 - 15 .07 1.70 .02 054 C .006 .250 .

40、167 .083 .042 .625 - 12 .12 3.00 .02 055 C .006 .250 .133 .067 .033 .125 - 15 .15 3.00 .02 056 C .006 .375 .133 .067 .033 .125 - 15 .38 12.00 .01 057 A .006 .150 .167 - - - - 12 .38 17.0 max Inches mm Inches mm Inches mm Inches mm .004 .005 .006 .008 .010 .028 .030 .032 .033 .036 .039 .041 .042 .045

41、 0.10 0.13 0.15 0.20 0.25 0.71 0.76 0.81 0.84 0.91 0.99 1.04 1.07 1.14 .050 .051 .056 .061 .062 .066 .071 .077 .080 .083 .088 .100 .111 .112 1.27 1.30 1.42 1.55 1.57 1.68 1.80 1.96 2.03 2.11 2.24 2.54 2.82 2.84 .120 .125 .132 .133 .142 .143 .150 .154 .166 .167 .168 .187 .200 3.05 3.18 3.35 3.38 3.60

42、 3.63 3.75 3.91 4.22 4.24 4.27 4.75 5.08 .230 .250 .25 .300 .312 .315 .375 .400 .500 .620 .625 .875 .940 5.84 6.35 6.4 7.62 7.92 8.00 9.53 10.16 12.70 15.75 15.88 22.23 23.88 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE ELECTRONICS SUPPLY

43、CENTER DAYTON, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 85136 REV E SHEET 9 4. VERIFICATION 4.1 Classification of inspections. The inspections specified herein are classified as follows: a. Materials and finishes inspection (see 4.3). b. Conformance inspection (see 4.4). 4.2 Materials and finishes i

44、nspection. Materials and finishes inspection shall be in accordance with MIL-H-87111. 4.3 Inspection conditions. Unless otherwise specified herein, all inspections shall be performed in accordance with the test conditions specified in the “General Requirements“ section of MIL-STD-202. 4.4 Conformanc

45、e inspection. 4.4.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A inspection per MIL-H-87111. 4.4.2 Inspection of packaging. The sampling and inspection of the preservation, packing, and container marking shall be in accordance with the requirements

46、for semiconductor accessories in MIL-DTL-19491. 4.5 Test equipment and inspection facilities. Test and measuring equipment and inspection facilities of sufficient accuracy, quality, and quantity to permit performance of the required inspection shall be established and maintained by the contractor. T

47、he establishment and maintenance of a calibration system to control the accuracy of the measuring and test equipment shall be in accordance with ANSI/NCSL-Z540. 4.6 Methods of inspection. 4.6.1 Visual and dimensional inspection. Heat sinks shall be examined to verify that the design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements (see 3.2, 3.3, 3.4, 3.5, 3.7, and 3.9). 4.6.2 Surface roughness (see 3.6). Material surface roughness shall be measured in accordance with ANSI B46.1. 5. PACKAG