DLA AN105201 THRU AN105300 REV 3-1986 BOLT - CRES HEX HEAD 5625-18.pdf

《DLA AN105201 THRU AN105300 REV 3-1986 BOLT - CRES HEX HEAD 5625-18.pdf》由会员分享，可在线阅读，更多相关《DLA AN105201 THRU AN105300 REV 3-1986 BOLT - CRES HEX HEAD 5625-18.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、- J - I AN105201 THRU AN105300 REV 3 53 U 7777915 0000262 3 FED. SUP CLASS I 5306 MTERIAL IDENTIFICATION PER MS28OO. RAISED OR DEPRESSED .o10 MAX .312 - L - 1.062 1.125 1. 188 1.250 1.312 L. 375 1.438 1.500 i. 562 i. 625 1.688 - - X +. O00 - .O60 .125 -188 .250 .312 .375 .438 .500 .562 .625 .688 -75

2、0 - IMPERFECT THD SECTION THRU THREAD PROFILE - -5625-18 UNF-3A SPEC MIL-S-7742 THIS BURFACE MUST BE SQUARE WITH SHANK WITKIN ,003 FULL INDIGAT3 RBADING .o90 CWEX 30 TO .%75 DIA (OPPOSITE SIDE OPTIONAL) AN105206 AN105207 105208 2.00.0 1.062 2.125 1.188 2.250 1.312 AN105209 2.375 1.438 AN105210 2.500

3、 1.562 AN105211 2.625 1.688 AN105212 2.750 1.812 AN10521 2.875 1.938 AN105212 3.000 2.062 AN105215 / 3.125 1 2.188 105216 3.250 2.312 PART NO. AMO5219 105220 AN105221 AN105222 AN105225 AN105226 AN10522g AN105229 AH105230 10522 3. 50 2.812 -a75 1 2.938 .o00 3.062 4.125 3.188 4.250 3.312 4.375 3.438 4

4、.500 3.562 4.625 3.688 4.750 3.812 4.875 3.938 5.000 4.062 PART NO. AN109 31 AN109 32 AN105233 AN105234 AN105235 AN105236 10523 AN10523g AN105239 AN105240 AN105241 AN105242 AN105243 AN105244 L 5.125 5.250 5.375 5.500 5.625 5 * 750 5.875 6.000 4.188 AN105245 4.312 AN105246 4,438 I AN105247 4.562 AN10

5、5248 4.6N AN105249 4.812 I AN105250 4.938 AN105251 5.062 AN105252 NOTE: (i) SHANK SHALL BE STRAIGHT WITHIN .O02 FIR. PER INCH OF BOLT LENGTH. (2) (3) THE CONCENTRICITY OF THREAD PD IN RELATION TO THE SHANK SHALL BE UITHIN .O06 FIR. THE CONCENTRICITY OF THE SHANK IN RELATION TO THE WASHER FACE DIAMET

6、ER AND HEXAGON SHALL BE WITHIN .O26 FIR. INACTIVE FOR DESIGN AFTER 27 DEC i966 NO SUPERSEDING STANDARD. HATERIAL: CORROSION RESISTANT STEEL - SEE HANUFACTURING SPECIFICATION SURFACE ROUGHNESS: AS107 HANUFACTURING SPECIFICATION: AH9 7679 . - . . - 1 INSPECTION: ALL PAKTS SHALL UNDERGO FLUORESCENT PEN

7、ETRANT INSPECTION IN ACCORDANCE WITH AMS2645. BREAK SHARP EDGES .003-.015 UNLESS OTHERWISE SPECIFIED. DIHENSIONS IN INCHES. UNLESS OTHERWLSE SPECIFIED: TOLERANCES; LINEAR DIHENSIONS i.010, ANGULAR DIHENSIONS f2. DO NOT USE UNASSIGNED PART NUMBERS. THIS STANDARD WAS DEVELOPED COOPERATIVELY WITH THE E

8、NGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SAE. P.A. Other Cust AIR FORCE-NAVY AERONAUTICAL STANDARD BOLT - CRES HEX HEAD .5625-18 AN I 0520 I AN I SF300 USAF - Il Army Navy - AV AS 0“IU“rnT simac OIXL ,.,.,$/,!, Project NO. 5306-1036 THIS DOCUMENT CONTAINS - - PAGES. ) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-