DLA A-A-59857-2010 ANCHOR SNOW.pdf

《DLA A-A-59857-2010 ANCHOR SNOW.pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59857-2010 ANCHOR SNOW.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 A-A-59857 11 January, 2010 COMMERCIAL ITEM DESCRIPTION ANCHOR, SNOW This commercial item description is approved for use by the Defense Supply Center, Philadelphia and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE. This commercial item description cover

2、s the requirements for snow anchors which are used for protecting climbers on steep snow routes by pounding the anchor into the snow or using as a deadman. 2. CLASSIFICATION. The snow anchors will be furnished in the following types and will meet the size and physical requirements of Table I. 2.1 Ty

3、pes: Type I Picket Type II Fluke 2.1.1 Type I. The picket will be constructed and comply with the sizes and requirements in Table I. TABLE I. Physical characteristics Type I (inches) 2.1.2 Type II. The fluke shall be sized in accordance with International Mountaineering and Climbing Federation (Unio

4、n Internationale des Associations dAlpinisme) - UIAA -154 Standard. 2.2 Sizing. The sizes will be defined by Type in 2.1.1 and 2.1.2 while meeting the standards in this description Comments, suggestions, or questions on this document should be addressed to: Defense Supply Center Philadelphia, Clothi

5、ng and Textiles Directorate, Attn: DSCP Standardization Team, 700 Robbins Avenue, Philadelphia, PA 19111-5096. Since contact information can change, you may want to verify the currency of this address information using Acquisition Streamlining and Standardization Information System (ASSIST) online d

6、atabase at http:/assist.daps.dla.mil/ . AMSC N/A FSC 8465 Picket Size Length, .25 inches Strength, kN Weight, Grams, 10% I 24 6 389 II 36 6 525 METRIC Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59857 2 3. SALIENT CHARACTERISTICS. The snow an

7、chor design shall provide ease of use with typical combat gloves and be as lightweight as possible, while meeting the standards in this description. 3.1.1 Type I. The picket shall be a T-shaped bar with a flange for reinforcement (modified T shape). The center portion of the shaft shall include atta

8、chment points sized to fit all types of carabiners in A-A-59836. The holes shall be evenly spaced along the length of the picket every 3 (+ .5) inches and reamed with no sharp edges. Both ends of the picket should be cut back in a slight V shape for ease of placement in snow. 3.1.2 Type II. The fluk

9、e shall be of a rectangular design with one end cut back in a V-shape. There shall be a wire sling for attaching carabiners to approximately center of mass on the body of the fluke. The wire sling should allow for a self-equalizing angle of inclination in the snow. The angle should not be fixed. The

10、 wire sling shall include a swaged loop for attaching all types of carabiners in A-A-59836. The fluke shall have holes in the body to provide “bite” on the snow. The wire sling shall extend between 60 centimeters and 120 centimeters. The fluke shall bend back away from intended direction of pull, al

11、ong its vertical axis, to provide stability in the snow. The top of the fluke shall have a stainless steel strike plate for protection when being placed. All swages should be protected with a plastic coating or sleeve. The main body shall have recessed notches for wrapping the wire sling around for

12、storage. 3.2 Color. The snow anchor shall be provided in a low reflectance, matte finish and provide low contrast with typical use terrain unless otherwise specified in the solicitation or contract order (see 7.2). 3.3 Materials. 3.3.1 Basic material The snow anchor shall be constructed of 6061-T6 a

13、luminum. 3.3.2 Sling material. Type II only. The wire sling shall be 4 millimeter (7X19) galvanized wire. 3.4 Tests. 3.4.1 Type I. The picket shall support a load of 6kN or greater when tested as follows: 3.4.1.1 Support the picket on the load bearing, snow contacting surfaces (the underside of the

14、top of the tee) with the gap between the supports equal to 15”. 3.4.1.2 Position the picket so that one anchor hole is centered in the 15” opening. 3.4.1.3 Apply a load to the center hole perpendicular to the length of the picket using a ” diameter pin through the hole. 3.4.2 Type II. The snow ancho

15、r shall meet International Mountaineering and Climbing Federation (Union Internationale des Associations dAlpinisme - UIAA) Standard 154 design and strength requirements. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59857 3 3.5 Workmanship. Th

16、e finished anchor snow shall conform to the quality of product established by this document. The occurrence of defects shall not exceed the contractors own quality assurance standards and the quality assurance standards defined in the technical data in the solicitation and/or contract. 3.6 Service l

17、ife. The snow anchor shall have no unexpected material or component failures during a continuous one-year cycle. The snow anchor shall have no unexpected material or component failures during periodic use over a five year period. 3.7 Labels/barcoding/instruction slip. If applicable, all labeling, ba

18、rcoding and instruction slip requirements shall be as specified in the solicitation or contract (see 7.2). 3.7.1 Labels. Each anchor, snow shall have identification label Class 5 conforming to Type VI of MIL-DTL-32075. The color of the label shall be white. The following information shall be include

19、d in the printing for the identification label for the anchor snow. ANCHOR, SNOW NSN: XXXX-XX-XXX-XXXX The following instruction information shall be supplied: a. the name or trademark of the manufacturer, importer or supplier b. the meaning of any markings on the product c. the use of the product d

20、. how to choose other components for use in the system e. how to maintain and service the product f. the lifespan of the product or how to assess it g. the effects of chemical reagents and temperature on the product h. the effects of storage and aging i. identification of the model, if more than one

21、 model is available 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.1 Recycled, recovered, or environmentally preferable materials. Recycl

22、ed, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operational and maintenance requirements and promotes economically advantageous life cycle costs. 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product confo

23、rmance. The products provided shall meet the salient characteristics of this Commercial Item Description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The Government reserves

24、 the right to require proof of such conformance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59857 4 5.2 Visual examination. Each snow anchor shall be examined for the following defects as listed in Table II: TABLE II. End item examination Ex

25、amine Defect Description Finish Not smooth and adherent Not low reflectance, matte finish Does not provide low contrast with typical use terrain Construction Not free of burrs, rough spots, slivers, flat areas or projections Any component loose, missing or not specified type Any component fractured,

26、 slit, punctured, dented, bowed, malformed or damaged Marking etched or indented, contains rough or sharp edges Swage Not swaged properly Wire sling Not sized properly Labels/barcoding/instruction slip (if applicable) Incorrect, illegible, omitted or misplaced. 5.3 Acceptance Criteria. Acceptance cr

27、iteria shall be as specified in the contract or purchase order (see 7.2). 6. PACKAGING. 6.1 Preservation, packing and marking. The preservation, packing and marking shall be as specified in the contract or order (see 7.2). 7. NOTES. 7.1 Sources of documents. 7.1.1 Government documents. Copies of Gov

28、ernment documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. DRAWINGS U.S. ARMY NATICK SOLDIER CENTER 3-3-0109 Anchor, Snow, Type I 3-3-0144 Anchor, Snow, Type II Provi

29、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59857 5 (Copies of drawings are available from the U.S. Army Natick Research Development and Engineering Center, Natick Soldier Center, ATTN: NSRDEC-RDNS-WPW-C, Natick, MA 01760) 7.1.2 Federal Acquisitio

30、n Regulations are available online at http:/acquisition.gov/far/index.html or by contacting the Superintendent of Documents at 202-512-1800. 7.1.3 Non-Government documents. Non-Government standards and other publications are normally available from the organizations that prepare or distribute the do

31、cuments. These documents may be available in or through libraries or other informational services. INTERNATIONAL MOUNTAINEERING AND CLIMBING FEDERATION UNION INTERNATIONALE DES ASSOCIATIONS DALPINISME (UIAA) UIAA Safety Standard 154 Mountaineering and Climbing Equipment, Snow Anchors (Copies are ava

32、ilable online at http:/www.theuiaa.org or from the Union Internationale Des Associations DAlpinisme (UIAA) Monbijoustrasse 61 Postfach CH-3000 Bern 23 Switzerland) 7.2 Ordering data. The contract or order should specify the following: a. Title, number, and date of this Commercial Item Description. b

33、. Type, size and color required (see 2, 2.1, 2.2 and 3.2). c. When required, labeling, barcoding, and instruction slip (see 3.7) d. Acceptance criteria (see 5.3). e. Packaging requirements (see 6.1). 7.3 Key words. Deadman Fluke Picket MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA FSS

34、Custodian: PREPARING ACTIVITY: Army - GL DLA-CT Marine Corps MC Project 8465-2009-015 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-