DLA A-A-59507-2001 CABLE ASSEMBLY POWER ELECTRICAL ADAPTER [Superseded DLA MIL-C-52286 22 REINST NOTICE 3 DLA MIL-C-52286 22 VALID NOTICE 1 DLA MIL-C-52286 22 DLA MIL-DTL-52286 22 .pdf

《DLA A-A-59507-2001 CABLE ASSEMBLY POWER ELECTRICAL ADAPTER [Superseded DLA MIL-C-52286 22 REINST NOTICE 3 DLA MIL-C-52286 22 VALID NOTICE 1 DLA MIL-C-52286 22 DLA MIL-DTL-52286 22 .pdf》由会员分享，可在线阅读，更多相关《DLA A-A-59507-2001 CABLE ASSEMBLY POWER ELECTRICAL ADAPTER [Superseded DLA MIL-C-52286 22 REINST NOTICE 3 DLA MIL-C-52286 22 VALID NOTICE 1 DLA MIL-C-52286 22 DLA MIL-DTL-52286 22 .pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: Defense Supply Center Richmond (DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-5610. AMSC N/A FSC 6150 DISTRIBUTION STATEMENT A. Ap

2、proved for public release; distribution is unlimited. INCH-POUND A-A-59507 30 May 2001 SUPERSEDING MIL-C-52286/22 4 May 1970 COMMERCIAL ITEM DESCRIPTION CABLE ASSEMBLY, POWER ELECTRICAL, ADAPTER The General Service Administration has authorized the use of this commercial item description by all fede

3、ral agencies. 1. SCOPE. This commercial item description (CID) covers a cable assembly adapter used for interior and exterior power and lighting (see figure 1). The adapter has molded male and female plugs, and pins (see figures 2 through 4). 2. SALIENT CHARACTERISTICS 2.1 Jacketing material. The ja

4、cketing material shall be medium-low temperature, heat resistant with the flexibility and durability of styrene-butadiene rubber (SBR) in accordance with the American Society for Testing and Materials (ASTM) D 518, “Standard Test Method for Rubber Deterioration - Surface Cracking“ (DoD adopted). 2.1

5、.1 Temperature range. The ambient temperature range shall be -55 C for the jacket material to +75 C for the conductors in accordance with ASTM D 1053, “Standard Test Methods for Rubber Property - Stiffening at Low Temperatures: Flexible Polymers and Coated Fabrics“ (DoD adopted). 2.1.2 Overheating.

6、Applying 600 volts (V) at 15 amperes (A) shall cause no overheating, arcing, or damage in accordance with ASTM D 1149, “Standard Test Method for Rubber Deterioration - Surface Ozone Cracking in a Chamber“ (DoD adopted). 2.1.3 Hardness. The Shore Durometer “A“ hardness shall be 60 +/- 10. 2.1.4 Insul

7、ation. The jacket material shall conform to the requirements of ASTM D 1765, “Standard Classification System for Carbon Blacks Used in Rubber Products“ (DoD adopted). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59507 2 2.2 Pin size. The end o

8、f pin hemispherical radius shall be one-half the pin diameter. The male pin shall be 0.594 to 0.656 high, and 0.154 to 0.156 inches wide as shown in figure 4. 2.3 Socket rounding. Female sockets shall be rounded for centering with metal bands on sockets. The socket depth for connector “A“ shall be 0

9、.594 inches to 0.656 inches. The socket width for connector “A“ shall be 0.154 to 0.156 inches. The socket depth for connector “B“ shall be 0.641 to 0.703 inches. The socket width for connector “B“ shall be 0.156 to 0.158 inches 2.4 Connector strength. The minimum bond between connector and cable sh

10、all be 150 pounds (lbs.) (see figure 1). 2.5 Connect/disconnect force. The connect/disconnect force shall be from 10-35 lbs. 2.6 Dielectric strength. The molded components shall withstand five times the rated voltage (600 V at 15 A) for one minute without damage, arcing, or breakdown. 2.7 Voltage dr

11、op. The voltage drop shall not be more than 10 mV at 15 A. 2.8 Adapter storage requirements. The adapter shall not be damaged when stored at -65 to 125 F at maximum humidity in accordance with ASTM D 518, ASTM D 1053, and ASTM D 1149. 3. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged

12、to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE PROVISIONS 4.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description,

13、and conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The Government reserves the right to require proof of such conformance. 4.2 Market acceptability. The following market accept

14、ability criteria are necessary to document the quality of the product to be provided under this CID. 4.2.1 The manufacturer/distributor of the item must have been producing a product meeting the requirements of this CID for at least 3 years. 4.2.2 The company must provide a warranty for replacing de

15、fective items. 5. PACKAGING. Preservation, packing, and marking, shall be specified in the contract or order (see 6.3(b). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59507 3 6. NOTES 6.1 Part or identification number (PIN). The PIN procedure

16、is AA59507-1. It is for government purposes and does not constitute a requirement for the contractor. 6.2 Source of documents. 6.2.1 FAR. The FAR may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402-0001. 6.2.2 ASTM standards. Copies of ASTM sta

17、ndards may be obtained from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. 6.3 Ordering data. Acquisition documents must specify the following: a. CID document number, revision, and CID PIN. b. Packaging requirements (see 5). 6.4 National sto

18、ck number (NSN). This CID is associated with NSN 6150-00-549-5401. Other NSNs may also correspond with this document. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59507 4 FIGURE 1. Cable assembly, adapter. Notes: 1. Connector A - see figure 2

19、2. Connector B - see figure 3 3. Minimum bond between connector and cable = 150 lbs. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59507 5 FIGURE 2. Molded plug, male. Notes: 1. The groove shall be of any shape with sufficient 0.010 inch = 0.02

20、54 cm depth, width, or cross section to support a 1/8 inch 0.015 inch = 0.0381 cm twine or cord. 2. Pin dimensions (see figure 4) A = 0.594 - 0.656 B = 0.154 - 0.156 3. Connector rating: 600 V at 15 A 4. Voltage drop: Not more than 10 mV at 15 A 5. Connect/disconnect force = 10 - 35 lbs Provided by

21、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59507 6 FIGURE 3. Molded plug, female. Notes: 1. This groove shall be of any shape with sufficient depth, width, or cross section to support 1/8 inch twine or cord. 2. Female contact dimensions (see figure 4):

22、C = 0.641 - 0.703 D = 0.156 - 0.158 3. Contacts shall be recessed by 0.125 inch (+/- 0.0156 inch) below face. 4. Connector rating: 600 V at 15 A 5. Voltage drop: not more than 10 mV at 15 A 6. Connect/disconnect force = 10 - 35 lbs Provided by IHSNot for ResaleNo reproduction or networking permitted

23、 without license from IHS-,-,-A-A-59507 7 FIGURE 4. Pin configuration. Note: 1. F - Point for voltage drop on contact. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59507 8 MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodian: Army - CR4 GSA - 7FXE Reviewer: Army - AT Preparing activity: DLA - GS2 (Project 6150-0282) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-